Having problems with your Digital Cameras ?

Lens error, restart camera - is the message I get when turning on my Canon Power Shot - any sugestions?


Answers :

Hello Typrice,
Thanks for the information, I had a Canon SD600 and I got the error message as " Lens error, restart camera", it was bothered me for long time and I couldn't figuer it out until today, I just followed the instruction above and fixed the problem in Fix #3, the camera now its working find. thanks.
Fixing a Lens Error on a Digital Camera
\015\012
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Digital Cameras

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Lens error, restart camera - is the message I get when turning on my Canon Power Shot - any sugestions?


Hello Typrice,Thanks for the information, I had a Canon SD600 and I got the error message as " Lens error, restart camera", it was bothered me for long time and I couldn't figuer it out until today, I just followed the instruction above and fix ... Digital Cameras

I have a Canon Power Shot SX120 IS camera. I turned it on and the lens open a portion of the way and I got an error message that say, "Lens Error Restart Camera". I put fresh batteries in it this morning and have only taken about 10 pic's. I turned the camera off and removed the batteries then replaced with new ones but I still get same message. Please advise if you can.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot SX100 IS Digital Camera

When I turn on my camera (Canon power shot SD600) it won't come on... I get a series of three beeps then a message on the screen that says "lens error, restart camera." The problem is, I don't know how to restart my camera.


Take it to a proffesional... ull need a new lens and more likely a whole new camera but dont start buying until u ask someone that know ALOT about cameras anyway id have to see it up close to know wat excatly is worng. !!!! try cleaning ur lens !!!! ... Digital Cameras

When I turn my canon A630 Power shot on, it makes the sound as though it is coming on and the lens does not extend... All I get is a written signal in lower left hand corner of screen after about 5 beeps "lens error, restart camera. And the cycle begins again. Is there anything I can do to fix this?


Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Canon PowerShot A630 Digital Camera

I have a canon power shot A590 they dont make them anymore everytime i try to turn it on it says lens error restart camera ad when i do it says that again i dont know what to do. What do i do that doesnt involve sending it back or getting a new one?


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot A590 IS Digital Camera

Lens Error Pertaining to my Canon Power Shot A590 IS: when the power is turned on, I am receiving an "Lens error, Restart Camera" malfunction. I turned the camera off and back on; still same issue. I also removed the batteries; still the same issues. What is your recommendation?


This message appears when a malfunction in the lens occurs. It could be a grain of sand jamming a gear or a barrel out of alignment. In any case, the lens is not serviceable, you would need to take your camera to your nearest repair centre to have it ... Canon PowerShot A560 Digital Camera

Canon A400 Hi, I have the above camera (canon power shot A400) and have just solved the E18 error by tapping the plastic A/V out cover - THANK YOU ! However, now, although the camera turns on, lense extends and I get full working order - after a few minutes I get the message 'Change batteriers'. and the camera dies. I have now put in several new batteries (including the little(cr1220) but the same message keeps coming up and the screen and the whole thing dies after a few seconds. Is this a furt


Having using standard LR6 batteries in a Canon before you will only get 3 or 4 pics max before it drains the batteries. You really need high power AA's like 2300mAH+ rechargeables for any good performance or Lithium AA's ... Canon PowerShot A400 Digital Camera

Own a Power Shot SX100 IS Canon camera. Camera won't work...am getting mesage, ¨lens error. restart camera''. When I go to the User Guide it tells me I need to contact a Canon Customer Suport Help desk as there may be a problem with the lens. I can't find contact information so am googling Canon and got this service. Can you help me?


Try the procedures in this tip. ... Canon PowerShot SX100 IS Digital Camera

Lens Error! I dropped my camera on the floor, and now the lens wont open fully or close. The LCD says "lens error,restart camera." But even when I turn the camera off, it still happens. Its a Canon Power Shot A550. I need to find out how to fix my camera without breaking it some more.


Same problem. The lens is stuck in the zoom position. When the camera is turned on, the lens moves a just afraction like it want to fully open or close, then the camera beeps and prompts with the "Lens Error" Restart Camera. Solutions? ... Canon PowerShot A550 Digital Camera

My Camera When I turn on my camera (canon power shot A420) the LCD screen is blank and reads 'Lens Error, Restart camera'. Can you please help me resolve this problem! Thank you


Try gently turning an knocking the cameras lens..i had the same problem an all it was,was the rubber protction guard had got stuck which is why the lens would not retract back into its position.so try twisting the lens gently or tapping it.well thats ... Canon PowerShot A420 Digital Camera

When trying to download pictures from my Canon Power Shot A590, I get an error message saying the camera cannot be found. The software is ok (I can download from another identical camera). The camera is turned on (with fresh batteries) and the mode switch is set to "playback". What am I doing wrong.


Try NOT connecting your camera to your computer.The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or c ... Canon PowerShot A590 IS Digital Camera

I dropped my Canon Power Shot a650 and now the lens will not open, I get a Message "lens error, restart camera". The camera then shuts down.


OK you are probably going to think I am loony giving you this advise But No I am completely sane!Get a can of compressed air OR acces to a compressor at your local garage Get them to fit the triggered air blower tool to it.Blo ... Digital Cameras

I have a canon power shot A540 and can not get the lens to close. When I hit the power on-off button- it says Lens error-restart camera. What can I do to solve this problem. Thank you. Sue


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot A540 Digital Camera

I have A1100 Canon Power Shot ! it have a problem with lens , when I turn it on , it says :"lens error , restart camera ! " How can I restart it?


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Canon PowerShot A1100 IS Digital Camera

My Canon PowerShot SD850 IS has a lens that is stuck in the extended position. I get a screen that says lens error, restart camera, but when I try to connect to the software, I get a screen on the computer telling me the computer cannot detect the camera. Battery is freshly charged, and I get the little yellow bird picture on the camera when I turn it on. It beeps about 4 times, and then turns off. Is there a safe way to get the lens to retract?


Don't play around with that lens, you can do more damage to the camera and focus with some of the stuff people tell you to try. Your camera just needs to be serviced and you'll be working great again. The shop that specializes in service for the powe ... Canon PowerShot SD850 IS Digital Camera

I have a Canon Power Shot S300 Digital Elph and use the Canon Digital Camera Solution Disc (Ver. 4.0). Part of this software is ZoomBrowser EX 2.6 which I use to download the photos from my camera to my computer. Recently I started getting the error message "There is not enough free memory to perform the operation". I have removed all of the photos from all folders and have also uninstalled and reinstalled all of the Solution Disc software but still get the above error message. This will not all


Memory errors are either free space on the C drive, Virtual Memory on C drive and almost always not related to your RAM.To check for Virtual Memory size in your PC, Right click My computer, click on the Advanced Tab, then click on the Per ... Digital Cameras

Canon Power Shot A2000 IS lens is stuck in out position. I had to replace batteries. I replaced them and when I turn on, it says "Lens Error, Restart Camera" and it shuts offs automatically.


The lens has probably got something in the retraction mechanism that is stopping it retracting. This can be something as simple as sand or grit or as a result of a drop or knock. In most cases the camera will need to be stripped apart to remove the l ... Canon Powershot A2000 IS Digital Camera

Canon Power Shot A430. Lens Error, restart camera. I've tried all the online fixes and am now at the taking apart stage. I can't get a definitive answer on what size/type of screwdriver I need. I have Phillips 00 & 0 and they are too big.


Bla ... Canon PowerShot SD500 / IXUS 700 Digital Camera

My camera and computer won't link up. What did I do wrong? I installed the Canon Digital Camera Solution disk. I restarted my computer. I attached the camera to the laptop via supplied cable. I clicked on program, Canon Utilities and clicked on each of the three camera windows. I get the response camera not found each time. I unloaded and reloaded the software, rebooted the system and got the same thing. Any idea what I could be doing incorrectly? Thanks. I have the Canon SD890 IS Power Shot.


Try going to my computer and see if it shows up as an external drive.\015\012That will tell you if the software. ... Digital Cameras

I have a canon power shot sx110is camera. how do i restart it? an error message says "lens error restart camera."


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is t ... Canon PowerShot SX110 IS Digital Camera

Lens problems I am deployed and I sent my camera to my wife and she has managed to brake it, I was hoping to get some help on this problem: When off, the camera lens is in the position as if it were being used. When turning the Canon Camera Powershot A530 on, the Canon logo screen comes on as it should. Following the blue logo screen is 2-3 rapid beeps made by the camera and a black screen is shown with the words, "Lens error, restart camera". Immediately after showing this screen for five


Try opening your camera, check the lens gear if its teeth are\015\012complete. If so, check if something stucks on it. Its much better to\015\012bring your camera to an authorized service center to re timing your\015\012lens track... ^_^ ... Canon PowerShot A530 Digital Camera

When i start the canon A55o power shot camera , the camera instead of opening it says lense error , restart the camera,again restarting the camera same display , what should i do ?


... Canon PowerShot A550 Digital Camera

When I turn on my Canon PowerShot SX10 IS Camera, I get the message, "lens error, restart camera." How can I restart the camera?


That just means to turn it off and then on. Also, try these:\015\012Fixing a Lens Error on a Digital Camera\015\012 ... Canon PowerShot SX10 IS Digital Camera

Hey, my canon SD890 has a problem, it says "lens error, restart camera" when I turn on, and the lens stick out and won't get back to normal. Is there any restart bottom that can restart my camera?


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Canon PowerShot SD890 IS Digital Camera

Lens error I have a canom power shot SD 1100 is I try to turn it on and a get an error that read as follows Lens error, reset camers then the camera turns off the lens is oin the open possition and have used a can of dust buster to try and blow any sand and or dirt dust out but nothing can anyone help.


The same thing happened to my camera, searching on the net for an answer and i found this. Strange, but it worked. Set your camera on a flat surface with the lens facing up. Tap it a few times and try again. Sounds silly but it worked! ... Canon PowerShot SD1000 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.7117 seconds