Having problems with your Digital Cameras ?

Camera turns on, the lens goes in and out a few times and a message comes up saying turn on and off again, when I do that it says the same thing

Answers :

Fixing a Lens Error on a Digital Camera
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Digital Cameras

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Camera turns on, the lens goes in and out a few times and a message comes up saying turn on and off again, when I do that it says the same thing

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Digital Cameras

I have a Canon Powershot A460 and when i turn it on there is a message saying lens error, restart camera..The lens will not come out and i never dropped this camera either. I changed the batteries but same thing. Can you help?

Hello,\015\012If this camera is under warranty you should carry it to the Canon Care Center they will replace the Zoom lens unit of your camera, or you need to get it replaced on payable basis as the lens has some ... Canon Digital Cameras

Cyber-Shot Dsc-W70 hi the lens won't come out i have to pull it to get it to come out then its all blurry and when i try to zoom it turns to a black screen and says turn off camera and try again and when the lens doesn't come out it does the same thing

Hi \015\012\015\012You probably have a faulty lens unit. You can make sure of this by checking that the spaces between the two rings that extend forward at switch on has the same distance between each other. \015\012\015\012If ... Sony Cyber-Shot DSC-F717 Digital Camera

Help! My camera is doing the same thing other's do too. I turn it on and it says "Turn power off and on again" and the lens comes out and goes back in halfway. sometimes I hold down the play button for about 5 secodns and then press it again and it allows me to take (bad) pictures. When i say bad pictures I mean the screen starts shaking and gets static or something and then when i finally can take a picture they exposure comes out so bright that the picture is just a all white or it comes out t

Hi try turning on and taking hold of the end of the lense and gently pulling and twisting you may hear a click but dont force it. then turn off and on again. then you may want to try\015\012\015\012\015\012Press Menu button to ... Sony Cyber-shot DSC-W55 Digital Camera

Lens error My Casio ex-z60 camara lens wont fully extend.When power is turned on, a clicking noise is heard. The LCD displays what will be captured, but is is blury. Then the lens closes and a "lens error" message apears on the LCD. Sometimes a message that says "retry power on" appears. Every thing else works fine. I am able to view my pictures .but I can not take any pictures.. Thank you

This is the lens focus gears. They are either knocked out of alignment, or debris has jammed them. The good news is it can be fixed....Casio most likely won't help. Hint...google my user name. ... Casio EXILIM ZOOM EX-Z60 Digital Camera

When I turn on the camera the lens comes out and then retracks and it says to turn the power off and on again. when I turn the camera off it says the same thing

Hi,\015\012I have to say that's a problem I've seen fairly often with the Sony W320. My suggestion is to take out the battery and make sure it's fully charged then put it back in. If that doesn't work I'd contact Sony. ... Sony CyberShot DSCW320 Digital Camera

The entire zoom lens will not come out when I turn the camera on. It moves a little, makes a sound, and then my camera says turn off camera off and back on. I tried that several times and it is still not working. The battery is charged. I did go to the beach and wondering if sand got into the camera. I also cannot review my pictures as the message comes up about turning it off. What is the best solution?

HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Panasonic Lumix DMC-TZ3 Digital Camera

When i turn on my camera the lens trys to come out but then it gets stuck and goes back in; the screen says "turn the power off and on again" but when i do the same thing keeps happening over and over. The camera has one big rechargable battery so i can't just replace it. I've tried doing the reset, and I've tried tapping around the lens ad hitting the sides or bottom of the camera but nothing has worked.

Here is a very reasonably priced quote for repair; https://www.teleplancamerarepair.com/quote/cart.asp?iProbID=5&mo=358\0 ... Sony Cyber-Shot DSC-S40 Digital Camera

My camera's optical zoom isnt working. when i was on holiday little bits of sand got stuck in the zoom lens and now it wont come out and isnt allowing me to take pictures. the camera turns on, but comes up with a message saying "turn power off then on again."

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Sony Cyber-Shot DSC-S40 Digital Camera

Sony-cyber-shot dsc-w50 I blieve that the battery if fully charged however when I turn the camera on all i see is a blank screen saying "access" with the lense zooming in and out then a message comes up on the sceen saying "turn camera on and off" I do this and the same thing keeps happening, could you please help? Sara

Lens unit is faulty, may have had sand or damage at some time, focus assembly inside the lens is not focussing ... Sony Cyber-Shot DSC-S40 Digital Camera

When i turn my camera on the lens keeps going in and out and then stops when it like half way out and a message on the screen says to turn power off an on again. But that doesn't do anything, it will turn off and then do the same thing when turned on. What's wrong?

Hi!The focus is stuck - could be sand or something. I work in a Sony service center and repair these every day. It will be quite expensive at Sony service center so I would recommend you contact a local repair shop.Tom ... Sony Cyber-shot DSC-W70 Digital Camera

Lens error When camera is turned on the lens will come out and then right away goes back in-an error message says lens error restart camera

Did you try replacing batteries.will it turn on long enough to restore it?if this is a new camera send it back it could be a software issue or mechanical breakage.Also get a can of air and blow the lens off to ensure no debris is ho ... Canon Powershot SX110 IS Digital Camera 9.0MP

Lens error, restart camera telephoto lens is stuck in zoom position and won't retract, so when i turn on camera, screens says "lens error, restart camera", but it won't restart...just keep coming up with same error message

Hello mnickoliThis is a fairly common error especially with the A560.This either means that something is jamming the lens , or that the\015\012lens sensor is faulty. This is a very , if not the most common problem\015\012with modern digit ... Canon PowerShot A560 Digital Camera

I dropped my panasonic camera onto the zoom lens. the zoom will not close, the shutter stays open. When I turn on the camera it says "please turn off camera and turn on again." When I do this the same message comes on again. Is it worth geting fixed?

... Digital Cameras

Lens problem The lens on my cannon powershot A1000 will not open. When I try to turn on the camera it makes a buzzing sound like it's trying to open and then a message comes on the screen saying lens error restart camera. This camera is pretty new so I'm not sure why the sudden problem.

You should have dropped your cam down to the floor or you should have forcibly tried to put your lens inside when the servomotor lens tried to bring the lens out..take your camera to the nearest service centre..you should not try to open the cam sinc ... Canon Powershot A1000IS 10MP Digital Camera with 4x Optical Image Stabilized Zoom

Lens error My zoom will not work. I can take pictures if I don't zoom, but as soon as I try to zoom in, the screen goes black, the camera beeps a few times and a message that says "lens error, restart camera". However, upon restarting the camera, nothing changes - it still won't zoom!. Also, when turning on the camera, when the lens first comes out...it sounds funny, like it is puttering. Help?

Powershot S3 IS: lens error message, lens juddering on startup but not \015\012coming out. Tried all tricks on internet without success, so decided to \015\012dismantle camera. Localised fault to optical position encoder on first \015\012transfer gea ... Canon PowerShot S3 IS Digital Camera

When I turn my camera on it says "Access" then a message comes up that tells me to "turn the camera off and then on" I have tried this many times and all the camera does is continue to push the lens in and out and then tells me to "turn camera off then on" Problem will not go away. Fully charged battery, took battery and memory card out for a while and re-inserted both and have same problem. [DSC-W55

This is a firmware problem that is common with many many digital cameras. It will have to be upgraded. The company will do this for $50Otherwise you may be able to find a kit online and do it which would be hard to located ... Sony Cyber-shot DSC-W55 Digital Camera

It keeps doing this when trying to turn on lens comes out then go's rite back in. message on the back of the screen says turn camera of and back on again.

Remove battery while lens is out. try reseting the cam usually near batt need paperclip to push reset. if the lens makes grinding noise lens assembly gears are done. flat rate from sony is usually close to 80% of what you paid for cam. ... Sony Digital Cameras

When i turn on the camera after a few seconds a message comes up on the screen saying Lens Error : 0x04110000 and then it turns itself off!! Is my camera broken or can this problem be resolved??

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Pentax Optio E60 Digital Camera

When you turn the camera a message comes on and says "please turn the camera off and then back on again" which i have done several times...i also took the battery out and let it sit and reinserted and same thing...any help would be great...email me [email protected]

HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that ... Panasonic Lumix® DMC-FS3 Digital Camera

I have a new Sony DSC-WX1 which I have used a few times it has developed a fault where it trys to turn on but the lens goes in and out a few times and then a message comes on screen saying turn the power off and on again! I recharged the battery but this has not solved the problem. Is this a known fault? Thanks for any help.

The motor that drives the lens must be faulty, since its new u can get it exchanged at the sony showroom or service center without any problem ... Sony Cyber-shot DSC-WX1 Digital Camera

When I turn the camera on the zoom lens goes in and out three times and then the message says to turn the camera off and then on again. I do this and it does the same thing. I was taking pictures and it was working just fine. It started to do this for no apparent reason.

It is a lens issue, will need to go in for servicing. Possible reasons are knock or grit/sand in lens unit. If you have had it to the beach on a windy day try holding it over a piece of white paper with lens down about a foot away from the paper, giv ... Panasonic Lumix DMC-FX33A Digital Camera

Camera Everytime I turn my camera on it comes on, but the lens goes in and out a few times before the screen goes completaly black and says to turn the camera off then back on again, I do, and the same thing happens all over again, not allowing me to take any pictures. However, I can still view the pictures that have been taken...and that are on my memory card.

It a lens misalignment try tapping the lens gently in an opposite direction the camera dropped on and that should pop the gear back into place ... Sony Cyber-shot DSC-W70 Digital Camera

When I turn on the camera, the lens opens and comes out, then closes and goes partway back in, then out and in again, then I get a message saying "Turn the power off and on again". I've tried but it doesn't fix the problem.

Your problem may be due to weak/worn out batteries or corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: r ... Sony Cyber-shot DSC-W170 Digital Camera

Hi When I turn the camera on and the lens comes out- the message on the screen says Lens Error 100.1.0,0 ( I think these are the numbers? Can you help? Thanks Leonie

Try these procedures. ... Kodak EasyShare M853 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.9067 seconds