Having problems with your Digital Cameras ?

When i hit the power button the lens comes out then it makes a beeping noise then it will go back in and repeat that a few times and then the lense will go all the way in and the screen will say lense error.

Answers :

Fixing a Lens Error on a Digital Camera
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Digital Cameras

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When i hit the power button the lens comes out then it makes a beeping noise then it will go back in and repeat that a few times and then the lense will go all the way in and the screen will say lense error.

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Digital Cameras

My Canon PowerShot SD850 IS has a lens that is stuck in the extended position. I get a screen that says lens error, restart camera, but when I try to connect to the software, I get a screen on the computer telling me the computer cannot detect the camera. Battery is freshly charged, and I get the little yellow bird picture on the camera when I turn it on. It beeps about 4 times, and then turns off. Is there a safe way to get the lens to retract?

Don't play around with that lens, you can do more damage to the camera and focus with some of the stuff people tell you to try. Your camera just needs to be serviced and you'll be working great again. The shop that specializes in service for the powe ... Canon PowerShot SD850 IS Digital Camera

I dropped my camera and now the lense wont retract all the way. a red screen pops up and says "Lens error, try turning the camera off then on again' the lense wont come out, what do i do?

There can be a mechanical break or a lens mounting break due to the fall and so the camera must be opened out to reset the lens hood.\012You will need some experience to remove carefully and checck the drive for the dislocation of the motor con ... HP PhotoSmart M437 Digital Camera

Camera problem My daughter just received a new HP635 camera for her birthday. At first the camera worked fine, but after a few minutes of use, the camera started flashing the welcome screen repeatedly and the zoom lense would move in and out over and over until we opened the battery storage compartment of the camera. Opening the battery compartment is the only way to turn the camera off. Everything on the camera becomes inoperable when this process starts which now is every time the camera is tu


I have samsung ST60 I used it and then put it away for about 2 weeks, next time I switched the power on the screen says system error 251, 402db978, 00000230. The lense comes out and then it freezes in that position and can do nothing with it. I put it on charge but that was no help. Serena

... Samsung ST600 Digital Camera

Hello, I have a sanyo VPC-E760 camera and when I have it in playback mode it says Lense Error 27 and then when I switch it to try and take a picture it says Lense Error 12.. Is there a way for me to fix this problem with out purchasing a new camera?

You need repair o change the lens unit ,I haved this part , ... Sanyo VPC-E760 Digital Camera

Lens error When I turn on my camera it will say coolpix but then the screen will go black and the lens will adjust a couple of times then the screen says lens error on it. What should I do?

You should have dropped your camera down. try tapping the device when the message pops up. if it works then you are lucky if no then take it to a service centre to get it done. it costs about 60$ ... Nikon Coolpix 3200 Digital Camera

Olympus 4050sw. when i switch on the camera it gives me an error message saying clean card (which i tried several times) or giving me the option to format. i've recovered my pictures from the card through my pc and the pc recognises the card and the pictures fine. now when i try to format it says "card error". I've even tried resetting back to default and it still says "card error". help! is there some way i can do a hard reset?

... Olympus Stylus / mju 1050 SW Digital Camera

Zoom ERROR When I turn my Camera on it comes up saying Zoom Error. I can't Zoom in or out - and all I can see is a black screen. Last time I used it - I took a picture and put it bck in my bag - when I pulled it out again the error msg came up. It has happened once before and I reset the camera through the menu and the msg went away and the camera went bck to normal so when it happened again I press reset but this time it hasn't made a difference. Any suggestions?

HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will have to get it fixed by a pro ... Fuji FinePix A820 Digital Camera

The battery of my samsung s860 was recently dead so i though that was why the lens wouldnt go out all the way. I have tried two new sets of batteries and the camera is reacting the same way. The lense wont go out all the way, a blurry image is projected on the screen then the screen goes black, the green light flickers, it beeps rather obnoxiously three times and the lens retracks again as it turns off. can my camera be resuscitated!?

The drive motor and actuator for the auto focus is defective, this is the most common problem i see after battery issues, yes the camera can be fixed, but here is the deal, they don't sell the parts to fix it to the public, only Samsung ... Samsung S860 Digital Camera

I dropped my canon rebel xsi from about 7feet, but it still took pictures after i checked it. nothing cracked, not the lense, or the screen. but than about an hour later, when i tried taking pictures it said error 99. i took of the lense and tried cleaning it inside, and when i put it back on it still said error 99. it says shooting is not possible. turn the power switch to off and on again, or reinstall the battery. i did those, but the error 99 keeps poping up. i dont know what to do?

It could be several problems. One is a bad contact between lens and camera body, clean the contacts , check for damage and try another lens if you have one. Try another memory card. Another problem could be with the shutter which would need the camer ... Digital Cameras

My nikon coolpix s220 is showing a lense error. i'll turn it on and the lense will pop up and go back down like, five or six times, and then the screen will display a lense error. it sounds kind of like it's struggling to open, or at least working harder to open it that it usually does.

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Digital Cameras

Lense Error I have nikon coolpix s6.I have a problem with it.every time i am going to open it a white screen appears showing lense cover error.But lense civer is fully open.After sometime when the screen light goes off again on clicking it is working perfect.I go to nearby Nikon Service center.They told me that disc driving mechanism is not working.So i have to repair it and it is costly.Please suggest me asap what i should do.Thank in advance

\015\012\015\012I have a solution for Nikon coolpix S5/S6. You can try my document "nikon s5 s6 lens cover error repair.doc"  uploaded on site http://www.esnips.com/web/papputatiyasStuff ... Nikon COOLPIX S6 Digital Camera

Screen error! unless i hold the lense when i first turn it on and press with my finger to the left or press the view button and hold the lense the press it again to take pictures the screen is black sometimes it is purple and sometimes it white. unless i keep a hold on the lense but then i can only take so many pictures that way! is there a short in it or dust? please help me!

Sorry to tell you but I think you have a bad cable on your CCD. You have to take it to be repaired at a shop. ... Fuji FinePix F470 Digital Camera

I purcahsed a new canon SLR 7D and have an error message on the LCD screen E30. instructions says to remove battery pack or turn off the camera but it seems its not working at all. i have tried so many times but the error message keeps appearing on the LCD screen. What can I do?

According to Canon's Knowledge Base here, this error means that there is ... Canon Digital Cameras

My Friend dropped my DSC-W30 camerashot on brick floor (it was nocked off a not very high table) and now when I try to turn it on.. the lense just comes out then half way in then out.. (it looks liek a confused robot) like no joke. and all the screen says while it is doing this is " Access " and after a min or two.. it makes this beeping sound and the screen says " Turn the power off, and on again " ? i tryed it.. it continues the same rutine. Please help? my father gave this to me as a gift for

Unfortunately the camera is non repairable short of dropping it again in hopes it jars the auto focus alignment back into position. this is a one in a million shot , but what have you got to lose. ... Sony Cyber-Shot DSC-S90 Digital Camera

File Error My camera seems to be taking the pictures just fine but when i go to view them some pictures take a long time to load onto the screen and then they go to a blue screen where it says "file error" i dont know what it is.

File error means it cant read the file or the file is corrupt, i would try a new memory card or format the one you have. ... Sony Cyber-shot DSC-H9 Digital Camera

When I turn on the camera is says there is a "lens error, restart camera" and when it is attempting to start it beeps a few times and a blue screen pops up and it says Canon just before the error pops up.

HelloThank you for using FixYa for your problemAlways check the batteries first but if is it still giving the same fault, your camera is faulty. It should be taken to an authorized repair centre for a repair ... Canon PowerShot A560 Digital Camera

When turned on screen reads "lens error" and the camera struggles to open the lens. It won't open the screen says error and only way to turn off camera is to pull the battery out.

Does the lens seem stuck, does it not extend or retract properly? Try to unstick the lens by gently pushing it in or pulling it out a little bit. IF that fails, the gears are too misaligned to repair it without opening it. ... Nikon Coolpix S210 Digital Camera

Lense error and i cant fix it and the screen just comes up and says lense error

Hi there, Well lens errors is a very common error on Digital Camera. Usually it's sand or grit interfering with the lens extension mechanism. Follow the below steps to do a try to correct it -1. Remove the batteries from the camera, ... Digital Cameras

My Friend dropped my DSC-W30 camerashot on brick floor (it was nocked off a not very high table) and now when I try to turn it on.. the lense just comes out then half way in then out.. (it looks liek a confused robot) like no joke. and all the screen says while it is doing this is '' Access '' and after a min or two.. it makes this beeping sound and the screen says '' Turn the power off, and on again '' ? i tryed it.. it continues the same rutine. Please help? my father gave this to me as a gift

Try Power Resetting the Camera.First, please turn OFF the Camera.Then, remove the battery pack from the Camera.Then, press and hold the POWER button on the Camera for 30 seconds.Then, reinsert the battery pack and check whethe ... Digital Cameras

Lense won't extend. Has error screen that says "lense error, restart camera"

Sounds drastic but turn on cam and grab hold of lens to try to fully extend it manually. if you hear a crunching noise that means the gears are stripped. not worth repairing ... Canon PowerShot SD600 Digital Camera

Minolta G500 My camera lense wont close says system error S0042. Didnt drop it just open the lense to take a picture and green,red light started to flash on and off and then on the screen it said system error S0042

Your lens mechanism is stuck up! try pulling the lens with slight force, if you are lucky the culprit that is blocking the mechanism will get loose. If you are not lucky theres no way you can remove or fix the problem than sending it to the authorize ... Konica Minolta DiMAGE G500 Digital Camera

Camera frozen I have recharged the battery and have changed charged batteries several times, howeverer when I turn the camjer on nothing happens(the lens is and remains extended ) but a red light blinks for a short while then goes off. The first few times that I tried to turn the camera on there was an error messafe on the screen saying error and a number but I don't remember what it was. Please can yoy help?

Try removing the memory card first then turn it on ...see what happensthe problem maybe with your card and not with the camera ... Kodak EasyShare C360 Digital Camera

Just purchased an powershot SX1 IS. I took one photo, zoomed in on it to see how clear the zoom was once taken a photo. THen it switched itself of with the lens still out. Now when turning it on it has a black screen and say lens error...restart camera. I have tried holding func. when turning on the camera and the time comes up on the screen. But as soon as I let go of func I get the error msg.

Hello if you just purchased this unit Then i advise you to take it back, this sounds like a system control issue or main board problem. Holding the function key while turning is factory reset, if this is not working right them the camera has a bad sy ... Canon PowerShot SX1 IS Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3556 seconds