Having problems with your Digital Cameras ?
Lumix dmcfs8 lummox when turned on says system error zoom and lens won't retract
This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Lumix dmcfs8 lummox when turned on says system error zoom and lens won't retract
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Digital Cameras
My canon ixus 75 is not turning on properly the zoom lense is stuck out and wont retract. When i turn it on it says "lens error reset camera"
OK, assuming the batteries are ok, the problem is within the mechanism for the lens being too 'binding' while it operates.\015\012\015\012Sometimes, people put their finger on the barrel of the lens when it retracts or extends.\015\ ... Canon PowerShot SD500 / IXUS 700 Digital Camera
When turning off the camera, the lens does not retract. I also get an error message "SYSTEM ERROR (ZOOM)" and another one "PLEASE TURN THE CAMERA OFF AND THEN ON". Once the camera is turned on, I can hear the lens mechanism working, but obviously failing.
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Panasonic DMC-FX37 Digital Camera
Zoom error MY olympus sp-550 has stuck lens. I turn it on, the lens extends then retracts immediately, saying zoom error. Why is that?
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed ... Olympus SP-550 UZ Digital Camera
Lens error, restart camera telephoto lens is stuck in zoom position and won't retract, so when i turn on camera, screens says "lens error, restart camera", but it won't restart...just keep coming up with same error message
Hello mnickoliThis is a fairly common error especially with the A560.This either means that something is jamming the lens , or that the\015\012lens sensor is faulty. This is a very , if not the most common problem\015\012with modern digit ... Canon PowerShot A560 Digital Camera
Hi my son dropped my digital camera while the lens was extended and now it wont retract and it says zoom error also the shutter wont open fully or close, the lens is at a slight angle and wont budge do i have to take it to get repaired or can i pull it apart myself thanks
HiIt helps to know the make and model of the camera, some cameras the lens is too fragile and we have never been able to repair them. Other models we have had a great deal of success repairing them. (Google: darntoothysam)One ... Digital Cameras
Basically the actual zoom lens is stuck out and wont go back into the camera, i have tried turning it off and on, but however still says "zoom error" and flashes red. i recently dropped in on the carpet and i think thats why the zoom lens is stuck out. please help
The lens maybe displace. Better go to a service center or an expert. ... Digital Cameras
Hi I have a Panansonic Lumix - DMC-FS25. My camera has now developed a fault with the lens which won't go back in. When I turn it on the lens zooms all the way out and then back in again and a message appears saying - System Error (Zoom). Any help would be greatly appreciated, Many thanks Graham
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Panasonic Lumix DMC-FZ20 Digital Camera
My kodak easyshare MD853 digital 8.2 camera has some problems.. When I turn it on it says: lens error message 122,1,0,0 and the zoom will not retract back into the turn off position.. I called Kodak & it's still under warranty however they say if it's something that not under warranty they will charge me anyway... I bought insurance through Target as well & they referred me to kodak. Does anyone have any suggestions on how to fix my camera?
My camera i dropped it and it was off and i waiting a few minutes and then picked it up and tried to turn for a photoshoot and the dum camera wont work now it says a lens error and it wont come up or anything, so i dont know what i should do ... Digital Cameras
'Zoom Error' Hi, I recently bought a Fuji FinePix s3000 Digital Camera. It took amazing pictures the first month or so, but recently I turned the camera on to find 'Zoom Error' across the LCD screen. I am unable to take pictures, and the lens wont Retract. I was hoping there would be a simple solution to this problem rather than a costly repair, seeing as how it was a very nice camera. Any Idea how to fix it?
Oh boy you are not going to like this but this is a problem that all fuji finepix s3000 will have I fixed it myself but only with a ton of patience and knowing what I was doingthe problem is that there is a gear in the lens motor as ... Fuji FinePix S3000 Digital Camera
Lens error When I turn the camera on it says "Lens error, restart camera," and turns itself off. When I turn it back on, the same problem occurs. The lens covers aren't completely closed, and the entire lens seems to be sticking out a little bit, like it didn't retract all the way. Please help! Thanks. Turn on the camera, camera shows a canon logo, then before turns off it said lens error, restart camera
\015\012\015\012I have a solution posted in doc "nikon s5 s6 lens cover error repair.doc" uploaded on site http://www.esnips.com/web/papputatiyasStuff&n ... Digital Cameras
When I turn the camera on in either record or review mode I get a system error: zoom message after a few seconds and the camera is inoperable. Then when I turn the camera off the lens does not retract.
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will have to get it fixed by ... Panasonic Lumix DMC-FZ28 Digital Camera
I dropped my camera and now the lense wont retract all the way. a red screen pops up and says "Lens error, try turning the camera off then on again' the lense wont come out, what do i do?
There can be a mechanical break or a lens mounting break due to the fall and so the camera must be opened out to reset the lens hood.\012You will need some experience to remove carefully and checck the drive for the dislocation of the motor con ... HP PhotoSmart M437 Digital Camera
My camera felt in the sand, so only tiny particles entered to the eye. The zoom does not work when it is on, there is not a clear image. when I turn on the camera. its lens protection does not opens and a message appears saying that there is a system error (zoom) . What can I do to fix it ands not buy another camera.
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Panasonic Lumix DMC-FS6 Digital Camera
My panasonic dmc zs5 dont work. When I turn the camera on I get this message, the camera will not work, and the lens does not retract when I turn the camera off. it then says system error focus. What is wrong ? The camera is from August so its not old.
... Panasonic Lumix DMC-FZ28 Digital Camera
We have a Panasonic DMC ZS3 camera that has been working fine until now. We are on the North West coast of Costa Rica. When you turn the camera on, the lens, which was out when shut off, goes in, then comes back out. The camera screen tries to focus, then goes to a blank screen and says "SYSTEM ERROR (FOCUS). When you shut it off, the lens does not retract.
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Panasonic Lumix DMC-ZS3 Digital Camera
I too have the same problem with my DMC-FS15:- When I turn the camera on in either record or review mode, I get a system error: zoom message after a few seconds, and the camera is inoperable. Then when I turn the camera off, the lens does not retract. Is there updated software that can be downloaded and installed via the supplied USB cable, or any other fix? Regards Martin J
Well perhaps it is just the battery I wonder if this problem isn't simple a bad battery try a replacement, as sometimes they just go bad, and this is indeed a symptom of a battery not working properly. If you have an original power supply, then try i ... Panasonic Lumix DMC-FZ28 Digital Camera
Lens error The lens on my Sanyo VPC-E760 will not close. I was not dropped, I was using it to take a picture and turned it off, but the lens never retracted. Now when I turn it back on, it is stuck in zoom mode and give an lens error message when I try to zoom back out, then it shuts itself off. Battery is fully charged. Any suggestions?
Hey jennbrady24,\015\012 What is most likely causing the lens error is that something is obstructing the movement of the lens (i.e. sand). I would first try removing the batteries and the memory card and waiting at le ... Digital Cameras
Lens error when i go to turn on my camera it says "lens error" on the screen and wont turn on Lens is 'stuck' open. I get a 'lens error' and a grinding sound...then the camera turns itself off
Wheni go to turn on my camera it says"lens error"on the screen and wont turn on lens is "stuck"open. ... Nikon COOLPIX L3 Digital Camera
Lens error My zoom will not work. I can take pictures if I don't zoom, but as soon as I try to zoom in, the screen goes black, the camera beeps a few times and a message that says "lens error, restart camera". However, upon restarting the camera, nothing changes - it still won't zoom!. Also, when turning on the camera, when the lens first comes out...it sounds funny, like it is puttering. Help?
Powershot S3 IS: lens error message, lens juddering on startup but not \015\012coming out. Tried all tricks on internet without success, so decided to \015\012dismantle camera. Localised fault to optical position encoder on first \015\012transfer gea ... Canon PowerShot S3 IS Digital Camera
Lens error When I turn the camera on it says "Lens error, restart camera," and turns itself off. When I turn it back on, the same problem occurs. The lens covers aren't completely closed, and the entire lens seems to be sticking out a little bit, like it didn't retract all the way. Please help! Thanks.
Try the procedures in this tip. ... Canon PowerShot SD750 / IXUS 75 Digital Camera
Just purchased an powershot SX1 IS. I took one photo, zoomed in on it to see how clear the zoom was once taken a photo. THen it switched itself of with the lens still out. Now when turning it on it has a black screen and say lens error...restart camera. I have tried holding func. when turning on the camera and the time comes up on the screen. But as soon as I let go of func I get the error msg.
Hello if you just purchased this unit Then i advise you to take it back, this sounds like a system control issue or main board problem. Holding the function key while turning is factory reset, if this is not working right them the camera has a bad sy ... Canon PowerShot SX1 IS Digital Camera
It dropped on the floor and it's lens are bent so it wont come in or out but i can still turn the camera on but it says system error
The problem is more complicated to resolve at home.Ask a friend skilled in electronics or go to service center (too expensive) ... Sanyo Xacti VPC-S60 Digital Camera
Lens wont retract when shutting off. System error (zoom) on screen.
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed ... Panasonic Lumix DMC-FS15 Digital Camera
I have a Sanyo X1200 that I've had for a couple months. It was accidentally dropped when a picture was being taken, which has happened once before but it fell right on the lens. Now it won't zoom in & out, it won't close, & when I turn my camera on it says System Error. Please help
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Sanyo Digital Cameras