Having problems with your Digital Cameras ?

When i switch "on", lens


Answers :

Fixing a Lens Error on a Digital Camera
\012


\012

This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
\012

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
\012

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Repair Help & Product Troubleshooting for Digital Cameras

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Canon Powershot S3 IS and I was looking at picture I had taken and the lens was retracted. I switched to the camera mode and the lens started to come out and hit my leg and stopped half way. The lens went dark. I turned it off to retract the lens and then turned it back on. The lens came all the way out but the screen is still black and I could feel the camera and just barely hear it making the noise it makes when the lens is coming out but it was already all the way out. I switche


Format ur memory card ....and replace the cells.....might work...contact the customer care for help ..they mightr be able to fix it ... ... Digital Cameras

My nikon d40 wont take a photo with the standard lens unless I switch it to manual but when I put the telephoto lens on it works in both auto and manual. How do I get my standard lens to work in auto (the "a" switch on the lens)? It has worked in auto in the past.


Hi,\012\012Sorry to hear about your lens. If you are able to take pictures with a telephoto and any other AF-S lens, then it means that your problem lies with the standard lens. With standard, I assume you mean the kit lens. If you can take pi ... Nikon D40x Digital Camera

Good Day. I dropped my Nikon Coolpix L16 camera onto a table. Since then when i switch the device on the lens goes out about a quarter and the goes back in and i get a lens error message. I noticed that when the lens goes out it bends to the right(looking from the top) and gets stuck by something. When i pull the lens a little to the left while switching it on everything works fine. A very small metal part came out of the camera. Any ideas? is it repairable?


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Digital Cameras

Lens error When the camera is switched on the lens does not open out and the lens cover does not open. The camera then displays a "lens error" message and suggests that the camera be restarted ten switches off. This happens repeatedly.


This is probably THE most common failure among digital cameras. There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Canon PowerShot SD750 / IXUS 75 Digital Camera

Lens error CoolPix L11. I switch on the camera The lens comes out. A picture is shown for about 1 second. Then the message Lens Error is displayed. The lens is retracted. After 15 seconds or so the camera switches itself off. The camera was bought in USA as a gift for a friend in Sri Lanka. Not so easy to get a local repair - if this is at all possible anyway. What is your advice? Thanks James


Try the procedures in this tip. ... Nikon Coolpix 5700 Digital Camera

When I turn on my Nikon D40 with the 18-55 mm lens set to autofocus I get an error message "Error. Turn Camera off and then on again." If I turn the lens switch to manual, I do not get the error. If I attache my 70-300 mm lens, I get the error regardless of the lens focus switch psition. I have just upgraded the firmware with no improvement.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Nikon D40 Digital Camera with G-II 18-55mm Lens

I have a new (3 weeks) D700 and while taking photos yesterday with camera and a 16-35mm lens, the exposure meter went ape. Pictures taken ok but ERR started to flash where shutter speed reading should be displayed in viewfinder. Tried everything, including resetting to factory settings, detaching and reattaching lens, checking switches, and then went home in despair. At home I switched to a 50mm lens and the problem disappeared. I put the 16-35mm lens back and problem seemed to have disappeared.


... Nikon Digital Cameras

I have a Canon XM3 camcorder. It has given me many years of good service. Recently it has developed a fault. When I switch it onto Camera mode, and then flip the switch to Standby, the small screen flickers blue for a short time, but it does not show the image from the lens. If I switch off, and sitch to Playback, the small screen works OK and all the Playback works fine. Sometimes when I switch to Camera, and Standby, the small screen flickers blue, and then an image from the lens appears, but


Its the problem of CCD assembly\015\012CCD (image sensor) failures, particularly in conditions of high heat and humidity, led to cameras capturing images with either no picture at all, or with extreme distortion and se ... Digital Cameras

Lens error when ever i want to switch on my camera it says on the screen "lens error" in the middle and sometimes if i am lucky it will evetually work but afterwards when i want to switch it off and put the camera on again it comes up with "lens error" PLEASE PLEASE help me solve this problem!!! :)


This is probably THE most common failure among digital cameras. There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Vivitar ViviCam 4345 Digital Camera

Camera jam Ricoh Caplio R5 - tried to switch it on to take a picture, and lens came out part way but the camera then switched off. Flat battery perhaps, so charged battery overnight and tried again with similar results. Lens still part way out, maybe some whirring noises, screen flashes but then camera switches off. Any ideas? Dead battery / broken charger? - or problem with camera? And how to check (I only have the one battery)


All the R series Ricohs have a pretty complicated lens system employing 2 swing-out lenses which can get stuck pretty easily, or worse, broken. If you are very good at taking things to bits you might have a go at fixing it (I've done several that wer ... Ricoh Caplio R5 Digital Camera

I have a Samsung PL100 digital camera. I dropped it while at beach, it was switched off. When I went to switch it on the lens came out but then it made a buzzing sound and switched itself off. The lens is still out but the shutter cover is still open. I love my camera and take it everywhere with me, can you help?


I had the same exact issue.... try putting it on the charger, even if you think it's fully charged... If the light is red, leave it on the charger until it turns green, and then remove the battery for a second and then put it back in the camera befor ... Digital Cameras

My camera lens was stuck out, and could not turn on the camera, but i have got the lens closed now, and it now switches on but when i switch on my camera the screen is blurry and when i try to use it, it beeps 3 times and switches itself off. any advice?


You probably still have a lens problem...try these:\012\012Fixing a Lens Error on a Digital Camera\012\0 ... Samsung L210 Digital Camera

My samsung camera lens wont come out it seems to be stuck. when i switch the camera on it just beeps and switches back off, you can see the lens trying to come out but then it beeps and switches back off. What is wrong with it?


Try these procedures. ... Samsung Digimax L60 Digital Camera

I have a canon EOS 450D Digital Camera & it won't auto focus using the smaller lens when switched to AF. The larger lens works fine when switched to AF, does it need cleaning or do i need to get new lens?


Hi dear boyd kellie, try clean the lens contacts if no solve contact a Canon service.Best regards ... Canon EOS 450D Digital Camera

Have a 20 month Optio E 40, today tried to switch on, lens woundnt come out, used the manual and switched on while holding arrow button, Playback piture showed in display, pressed half shutter to switch back and error message Lens error 113,0,0,0 appeared, Pentax want £80.00 minimum to look at it, can you help pleaseregards Terry


Try to take out the battery and put it back in. ... Digital Cameras

Jammed lens My zoom lens is jammed, and when I switch on the camera the red light switches on but no picture appears on the screen. The zoom lenses remain as they are when the camera is both on or off. (they are jutting out as if the camera is switched on.) Can I repair my FE-210 and if yes how?


Would be best to send to repair center ... Olympus FE-210 Digital Camera

Camera lens movement mechanism seems to be damaged, as when switched on, the camera lens does not extend out completely and the object appears blurred on the screen. Similarly when switched off, the lens does not retract back completely and it needs a manual push to put it in a little more. But even then it does not go in fully. Rest of the functions are working well. The damage is the result of an accidental body weight going on the camera, when it was in on condition.


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Digital Cameras

My Ricoh R4 camera has its lens stuck in the fully extended position. After switch on, it makes motor noises for a while and then stops and switches itself off. Switching the camera on and off does not move the lens. Also, operating the zoom buttons does nothing. Having this great little camera working again would be fantastic!


Hi there,Make sure the camera is fully charged. Then try this: Turn off the camera and hold it on your right hand with the lens facing the ground. Then hit the camera's base on your left palm as you turn it on. You might want to do th ... Digital Cameras

On/Off Switch Hi My problem with the 5050Z is as follows; When I switch the camera on the lens extends and then retracts but not always. This can carry on until I turn it off. On the odd occasion that this does not happen, should I lightly touch the on/off switch (but not move it) the lens begins to retract and extend again until I turn it off. Has anyone experienced this problem, if so, is there a solution? I've tried removing the batteries for 24 hours to force the camera to fully res


I too have experienced the same situation .... I have THREE C-5050's and "REGULAR" part seems to occure when the camera is overworked, or WARM. Does your camera become warmer is you are shooting many picturees one after the other? When it cools down ... Olympus Camedia C-5050 Zoom Digital Camera

I DROPPED MY COOLPIX L6. When I switch it on the lens extrudes normally and I can take a photo. When I switch it off there is a buzzing sound as if the lens is trying to retract. I then get the message Lens error and a Triangle appears with the ! sign. Question: Is it possible to repair the damage


Hi,\015\012\015\012As motor is running but lens won't retract sometimes lens would slip off with the gear or break off a tooth in the gear when it gets dropped. Try to gently move the lens barrel around with the finger and see if it is moving, ... Nikon Coolpix 5200 Digital Camera

Kodak V1003 A few weeks ago, shortly after I'd taken a pic, the lens refused to retract and the camera switched off. It has never been dropped or had anything spilled on it. Strangely, when I press the button furthest left the camera comes on, allows me to view pictures on the card, set the time etc - everything except take pictures. Again when I try to switch off, the lens does not retract. Does this not suggest a software glitch of some kind?


No, unfortunately that is a problem with the hardware, software would not prevent the lens from retracting.\015\012\015\012If it is within manufacturer's warranty (usually 1 year) take it to any Best Buy they will send it out to the mfg f ... Kodak EasyShare V1003 Digital Camera

L 730 camera After switching on the camera the lens came out then it stopped working and hanging on. The power button is lighting but the display is remaining dark and the only way to switch it off is to remove the battery. But the lens does not move at all.


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Samsung Digimax L730 Digital Camera

When switching the power on, the green light goes on, the lens comes out, then there is a buzzing/clicking noise. The lens then goes back in and it switches itself off. Help please!


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Casio EXILIM EX-FC100 Digital Camera

When I try to switch my camera on the lens partially comes out and then retracts again and switches off. The message on the screen reads 'lens error'.


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Casio Exilim EX-Z1200 Digital Camera

Camera my lens is out and when i switch camera on it comes up on the screen lens error and switches itself back off before i can do anything


Use your thumbs and gently yet firmly push the lens assembly back into the camera until you hear a confirmation "click" ... Kodak Easyshare M753 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1033 seconds