Having problems with your Aqua Pentax Optio S12 Digital Camera ?

Wont stay on and lens stuck in the out most position battery full any suggestions steve


Answers :

Fixing a Lens Error on a Digital Camera
\015\012
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Aqua Pentax Optio S12 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wont stay on and lens stuck in the out most position battery full any suggestions steve


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Aqua Pentax Optio S12 Digital Camera

We have a CoolPix L3 that is not very old nor has it been used (and or misused); perhaps 14 months old. Serial No. 30649827. The telescoping lens has tended to get stuck in a closed position. After installing FRESH new batteries, I gently tapped the camera body against my other hand and the lens opened but continued to move in and out. Sometimes it would stay open but not at its maximum position. Furthermore a message was displayed; LENS ERROR.What do you suggest we do. Is it repairable?


The lens has to be unlocked, thereby meanig that we need physically open the camera and check the three rollers which control the lens movement inside the camera. ... Digital Cameras

My camera lens is stuck. I turned it on, it ran out of battery, it turned off, the lens stayed open, put new batteries in (positively the right way), turned on, blank screen, lens won't shut.


Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Samsung Digimax S500 Digital Camera

Dead battery? I have been searching everywhere for help on this problem and so far, no luck! My camera will turn on but as soon as it does, it shuts itself off again. The lens is stuck in zoom mode and won't retract. I tried charging the battery but every time I try, it will only charge for about 5 minutes and then says the charge is full. Is this a problem with the battery? Charger? Or is the battery fine and it's a problem with the camera? Any suggestions?


Ugh. I have the EXACT same problem!!!!! It's extreamly annoying. When I turn my camera on it turns on, you see the polaroid screen, and theres this buzzing sound? and then it turns off. I'm so frustrated and don't know what to do. Should I take it in ... Polaroid T737 Digital Camera

Is there a way to "restart" my Casio Exilim EX-Z700? While I was taking a picture it seemed to freeze while it was trying to display the picture I just took - then, with the lens still popped out the screen stayed blank and it turned off, and now it won't turn on. The lens is still stuck in the "out" position. No buttons work. I tried to put it in the cradle to charge, and tried a different battery as well. Nothing works. Camera is dead!


Normally changing the battery solves this.Make sure you replace it with a good quality new battery and make sure it goes in the right way around as when you get in a flap it often ends up in the wrong way! ... Casio Exilim Zoom EX-Z700 Digital Camera

The lens on my Olympus m760 camera is stuck in its out position. Even When i turn my camera off or take the battery out, the lens stays fully zoomed out and makes a funny noise like its tyring to retract. Please help.


This is probably caused due to a fall or so.. try to technically have a 360 look at the sides of the lens were at one instant u will notice a slight droop.. now u have to carefully push the lens in carefully with **** like motion for which a click no ... Olympus Digital Cameras

Lens stuck My Sony Cybershot lens is stuck in the out position. It occured when I went to take a photo, the camera turned on and then the battery went dead; not enough juice to turn it off. It was frozen like that for about a day and a half, I did not have access to an outlet. Once I charged the battery, it not struggles to move but is stuck. The LCD display says, "turn power of and then back on" Is there a trick to un freezing it? I don't want to send it in for repairs, my warrenty is exp


Hello, I have read other forums that suggest that quite literally rapping or swatting the unit on its bottom half can actually solve the problem and get things going again. I am going to try it with mine. I too have a stuck lens. Here is a link that ... Sony Cybershot S650 Digital Camera

My nikon p60 will not turn on and cannot reset. the lens is in 'on' position, but when i hit off button, lens stays in place. i then take out good batteries and replace the batteries and same problem occurs. in other words, cannot turn cam to on position


... Nikon COOLPIX P60 Digital Camera

Nikon coolpix 5000 zoom lens is stuck in extended position when battery died. replacing battery I now get error message: Remove lens cap. but the cap is off- I cant get the lens to retract.


... Digital Cameras

I have a Kodak EasyShare Z1485 IS, the lens barrel is stuck in the furthest extended position. It was left alone and not operated for several months, though I have replaced the battery. The camera turns on for about 3 seconds at a time, I tried to turn it on several times with the lens barrel inching forward each time. It stopped going forward and has become stuck in what appears to be the furthest-extended position.There does not appear to be any particulates obstructing the lens barrel as far


Your camera almost certainly has a lens error ... Kodak EASYSHARE Z1485 IS Digital Camera

Lens is stuck in full zoom position Olympus 7010 camera


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Olympus Stylus 7010 Digital Camera

Lens stuck The camera lens is stuck in the out position and the camera won't turn on at all. The camera was working just fine a the day before this happened. I have replaced the batteries and attempted to turn the camera on an off several times.


Lens unit faulty and camera has gone into error mode. Repair lens ( several possibilities here ) and reset camera and it will work fine. ... Fuji FinePix S3100 Digital Camera

I dropped my camera. In the off position, the lens stays open and projected. Then turning to the on position the lens goes in, then out again. Then I receive the message "Please turn camera off and then on again." Before receiving this message, the screen looks normal, as if it will work, but then the message comes up. I took the battery out to try to reset, but no change. Any suggestioins?


HelloThank you for using FIXYA!!!This\012 is a suggestion. If you do not feel comfortable trying it, you will need to ... Panasonic Lumix DMC-FX8 Digital Camera

My FE-360 keeps shutting down with the lens stuck out. When you try and turn it on you can hear the lens trying to retract but it stays stuck out and the camera makes a bleeping sound. I have noticed that if i open and close the battery cover whilst it is making this bleeping noise, the screen comes to life. All of the menus can be accessed and options changed but the picture seen on screen is very poor quality and the camera will not take a picture. As soon as you press the capture image butt


Your camera has a lens error, this\015\012 is such a common fault that I hop ... Olympus FE-360 Digital Camera

My fella dropped my samsung p1000 camera and tried to push the lens in because it froze. its now stuck. the power button comes on and stays on until the battery is removed but when its on nothing happens, blank screen, lens still half stuck out. Is there anything I can do like a reset button or something before I bin it?


Sounds like you need a new camera. The lenses on digital cameras are super sensitive - if you force it in - it's probably done for. ... Digital Cameras

Zoom error Lens stuck in the halfway-out zoom position (lens cover is closed)and I am getting the "zoom error" message.i try to 1.turn off/on again but not ok 2.take battery off for 1 hour but not ok 3.Changing new batteries but not ok please give me how this problem was solved by my self. thank you... (i had bought camera about 3 years .my camera ever sent to dealer because same ploblem about 3 time)


I had sent my camera in for the same issue and they did nothing to help with it. Seems to happen when battery gets low or dies, lack of on-screen battery meter doesn't help. Typically have to manually twist the lens to close it or open it after fresh ... Fuji FinePix E550 Digital Camera

Jammed camera The lens on my Digimax S800 Samsung camera is stuck in the open position and when I put new batteries in it and tried to turn it on it beeped three times then shut off with the lens still in the open position. What's up with that? Will I need to send it in to the manufacturer? [email protected]


A temporary fix to power up is to press the menu and power button at\015\012the same time. When the lens is extended and it beeps, on my camera ,\015\012the lens is *stuck* Give it a gentle tug , then try the power button\015\012again ... Samsung Digimax S800 Digital Camera

Lens problem When I turn on my camara it stays on for only 30 seconds, the blue screen stays on and the lens part wont open ,its stuck,, then the camara just turns back off. Ive replaced my AA batteries and thats not the issue. Someone please help,, christmaS is coming and I needed my camara. Thanks


I had the same problem with my canon powershot sd 400.\015\012The shutters would not shut and the lense was halfway out.\015\012When I turn on the camera, the screen saver stays on, and after a few seconds, it turns itself off.\015\012\015\012I got a ... Canon PowerShot A520 Digital Camera

Lens error The lens on my Sanyo VPC-E760 will not close. I was not dropped, I was using it to take a picture and turned it off, but the lens never retracted. Now when I turn it back on, it is stuck in zoom mode and give an lens error message when I try to zoom back out, then it shuts itself off. Battery is fully charged. Any suggestions?


Hey jennbrady24,\015\012 What is most likely causing the lens error is that something is obstructing the movement of the lens (i.e. sand). I would first try removing the batteries and the memory card and waiting at le ... Digital Cameras

Battery/Power trouble My C-770 is 2 years old and I still have the original L1-10B batterys that came with it. The camera goes through periods of non-use so has not been used excessively. When I put in a newly charged battery the battery indicator says the battery is full, but then take one picture and the light blinks empty and usually dies with the lens out and the ISO numbers still on the screen. I switch the power button into the off position but it generally takes a min before it actuall


Using a little common sense I'd be checking the batteries first. You're going to need a new one sometime anyway so get a new one and try it out. Just make sure your battery charger is working first. It sure sound like battery problems to me. ... Olympus Camedia C-770 Digital Camera

I purchased a Fujifilm finepix Z20fd camera from target last december. About a month ago, after putting a full charged battery into the camera I pushed the slider to turn it on and it would not come on. The battery charger tells me it is fully charged. After sliding the front back and forth a few times I left it in the "on" position and took out the battery and put it back in. It came on, but would not flash. Also I was able to close the slider, but the camera stayed on until I took out the


Have you tried putting your battery in different ways and did you push it in all the way to hear it click ... Fuji FinePix Z10fd Digital Camera

My Nikon Coolpix P2 would only work for about 5 minutes so I bought new batteries for it. It no longer works at all and the lens is stuck in the out position. I checked the voltage on the batteries and I am getting 4 volts from a charged battery. The camera has very little use on it and I really like the camera. Any advise


Contact Teleplan Camera Repair for repair. It can be a series of things.\015\012http://www.teleplancamerarepair.com/Nikon_Coolpix_L18 ... Nikon COOLPIX L18 Digital Camera

My Canon PowerShot SD850 IS has a lens that is stuck in the extended position. I get a screen that says lens error, restart camera, but when I try to connect to the software, I get a screen on the computer telling me the computer cannot detect the camera. Battery is freshly charged, and I get the little yellow bird picture on the camera when I turn it on. It beeps about 4 times, and then turns off. Is there a safe way to get the lens to retract?


Don't play around with that lens, you can do more damage to the camera and focus with some of the stuff people tell you to try. Your camera just needs to be serviced and you'll be working great again. The shop that specializes in service for the powe ... Canon PowerShot SD850 IS Digital Camera

Canon ixus 900ti lens error restart camera message coming up. Lens stuck in full out position, have tried restarting a couple of times but same thing and lens will not retract.


Canon ixus 900ti lens error ... Digital Cameras

Lens stuck in in position. Lens shutter stays open. Lens tries to open but won't. Thanks


Try these procedures. ... Fuji FinePix A345 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2793 seconds