Having problems with your Canon PowerShot A410 Digital Camera ?
Camere lens will not come out. Message code E24
This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Camere lens will not come out. Message code E24
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Canon PowerShot A410 Digital Camera
Toshiba PDR-M700 When I power up the camera, the lens will not come out and sometimes will come out all the way to maximum zoom. When I power off with the lens out, it clicks as if something is stripped or loose. After shut down, I can push the lens back in. Once in a while the camera will work but eventually the "Lens Error" message comes up. This was a good expensive camera when I bought it but taking it in for service would probably cost more than the price of a new camera today. Can you sugg
It sounds as though the drive gear is slipping... If you give up on trying to repair your camera I may want to purchase it for parts (my sister-in-law broke my LCD display)[email protected] ... Toshiba PDR-M700 Digital Camera
Upon trying to turn camera Panasonic DMC-ZS3 on, error message appears: system error (zoom). The lens comes out a bit and then goes back in, shutter closes, then lens comes out a bit again, then goes back in again ... then error message. Can you help? Thanks!
I don't know that I can help you fix it, but I can try.\012Here are my thoughts...\012Check the battery first. If it's like a normal battery, like AA or AAA batteries, replace them and try turning it on.\012\012If it's a flat lithium battery t ... Panasonic Lumix DMC-ZS3 Digital Camera
Hi I have a Sony Cyber shot dsc-w7 that when it powers up to use the camera the lens comes out but then I get the message Turnn the power off and on again. The lens does not retract on power off but stays out and the same message comes up again. I have put brand new Duracell betteries in still no joy. Help please Regs jts4u
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\012\01 ... Sony Cyber-Shot DSC-W7 Digital Camera
Hi there, I have a Canon Powershot S3IS and just lately when you try to turn it on it comes up with a message that says E24. I have looked through the manual and cannot find anything resembling this message. It turns on for a few seconds and then the screen goes black and displays the E24 message. I was taking photos during a recent wedding I attended and then it cut out suddenly and displayed the E24 and since then will not turn on. Please help me as my brother and his family are arriving soon
... Digital Cameras
I suspect that I have sand in the lens of my Nikon Coolpix 3200 model as it is dieplaying the 'Lens Error' message after coming back from a beach. The camera opens the lens and after s few seconds the lens closes and displays the 'Lens Error' message. Do you know if this is repairable?
Take it to a Nikon-authorized service representative and ask him/her whether its repairable. ... Nikon Digital Cameras
Lens error i pressed the on button, it comes on but the lens dont come out and an error message appears "lens error" also the lens not totally in or flat in the camera.
OK you are probably going to think I am loony giving you this advise But No I am completely sane!Get a can of compressed air OR acces to a compressor at your local garage Get them to fit the triggered air blower tool to it.Blo ... Nikon COOLPIX S710 Digital Camera
Lens error When I turn on my Nikon Coolpix 2200, the lens does not open and a "lens error" message comes up on the screen. This problem has happened before and after replacing the batteries or just waiting a few days it would work properly. Now I cannot make it work at all. lens error comes on opening,,,dont know what to do...
From the manual: "Turn camera off and then on again. If error persists, contact retailer or Nikon-authorized service representative." ... Nikon COOLPIX L18 Digital Camera
I have a Nikon Coolpix L14 and all of a sudden, when I turn it on, the lens moves in and out while making a strange noise until a "Lens Error" message comes on the screen. I tried replacing the batteries, turning it off and on, taking out the memory card, and cleaning the lens. The first time I replaced the batteries, it worked...until the next time I used it and the screen was completely blurred. Then, I had the original problem with the "Lens Error" message. I really don't think it is a conde
Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Nikon Coolpix L14 Digital Camera
I dropped my camera. In the off position, the lens stays open and projected. Then turning to the on position the lens goes in, then out again. Then I receive the message "Please turn camera off and then on again." Before receiving this message, the screen looks normal, as if it will work, but then the message comes up. I took the battery out to try to reset, but no change. Any suggestioins?
HelloThank you for using FIXYA!!!This\012 is a suggestion. If you do not feel comfortable trying it, you will need to ... Panasonic Lumix DMC-FX8 Digital Camera
I am trying to use my Olympus D-460 after not using it for ~ 4 years. I downloaded the pictures from the 16 MB card using my laptop with a card reader. I then emptied the card. When I pull back the lens cover, the lens comes out but then i get an error message that the card is full. I followed the directions for formatting the card but still get a message that the card is full even though it also gives me a no picture message. i copied some of the original pictures back on to the card and can v
Glad to hear you're back in business! ... Olympus D-460 Zoom Digital Camera
I have a small Panasonic Lumix DMC-TZ5 camera. After fully charging the battery I am all of then sudden getting this error message :"please turn camera off and then on again." When the camer is OFF the lens is extended and open. When I move the camera to ON the lens moves in to the closed position closes, then reopens, extends, tries to focus, is unable to and the error message appears "Please turn camera off and then on again" This cycle just repeats. The lens is able to extend it is not st
Hi,Checkout this tip about digital camera error messagesLens Errorfix for Digital Cameraheatman101 ... Panasonic Lumix DMC-FZ7 Digital Camera
When turning on the camera a message comes up reading " Turn the power off and on again" and the lens seems to be struggling to open. When I turn off the camera & then back on the same message comes up everytime, please help !
Have you tryed brand new battertys ... Sony Cyber-shot DSC-W170 Digital Camera
Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work.
*&%$@#%^&*&^% !!"It's working!!!!\015\012\015\012Turn your camera on and put it near your ear. Did you hear a softly motorized sound in the lenses area and the green LED is flashing? If you hear this sound do this.\015\012\015\012Do it under your own ... Panasonic Lumix DMC-LC33 Digital Camera
My camera is coming up with a system error (zoom) message and then locks up. The model ois Panasonic DMC-FS7. When it is switched on the lens zooms in and out a couple of times and them comes up with the message detailed above
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a p ... Panasonic Lumix DMC-FS7 Digital Camera
My camera wont open properly i dont know what it is it says lens error and has about 8 numbers like a code come up the lens wont come out what wrong with it
Try these procedures. ... Kodak Easyshare C813 Digital Camera
Code m437-001 My camera has displayed code m437-001, the lens cover does not open or close, also the lens does not come out fully or when switched off does not retract fully
Try the procedures in this tip. ... HP PhotoSmart M437 Digital Camera
Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work. hi expert i m suffring in this error on my panasonic DMC-LC33 when i switched on
Try \015\012\015\012Klomtrix trick this worked with my camera\015\012thanks klomtrix ... Panasonic Lumix DMC-LC33 Digital Camera
Lens Stuck My Lens is stuck on my Coolpix S200 and I'm getting the Lens Error message. I tried to push it back in like I read on here and it went partly in and now its completely jammed. I've only had my camera for about 4 months. Please help!! I'm hoping to fix it myself. i dropped my camera and now the lens wont come out. Everytime i turn on the camera it tells me to turn it off then on again. I've done it multiple times and it doesnt work. I tryed to push the lens in and out but it doesnt ma
YOU CANNOT REPAIR THIS SOPHISTICATED CAMERA YOURSELF!!\015\012I guess pushing the lens inside may have made the problem worse.\015\012I follow a rule- if you drop an electronic equipment and a problem occurs- it usually takes a profession ... Sony Cyber-shot DSC-S700 Digital Camera
I bought my camera 6-7 months ago. Now when I try to take pictures the lens comes out but I can't take a picture. and then a Lens Error message shows up on my screen and the lens closes. I can view pictures that I've already taken but that's it. I think the camera turned on while it was in my purse and somehow damaged the lens. What should I do?
Leaving the camera on and putting it where pressure is applied on the extended lens will damage the gears driving the lens mechanism in and out.There fore the problem was due to a broken gear mechanism.You need to bring it to a service/repair shop, b ... Casio Exilim EX-Z750 Digital Camera
Lens error When I turn on my Nikon Coolpix 2200, the lens does not open and a "lens error" message comes up on the screen. This problem has happened before and after replacing the batteries or just waiting a few days it would work properly. Now I cannot make it work at all. kinda dropeed it and now the lens is SLIGHTLY crooked...can i fix it myself?
No not likely ... Nikon Coolpix L11 Digital Camera
Lens Error I purchased a Nikon P90 a month ago; and it was working just fine. A couple of days ago during a photo shoot (after taking 190+ photos without any trouble), the camera went crazy.. It shows a lens error when turned on; asks to 'remove the lens cap' even if it is already removed. The lens starts to zoom out & in for a couple of times; then this error message comes up and just hangs. Tried removing the card, battery and even tried re-charging the cell. I purchased it from UK, and I'm n
This is probably THE most common failure among digital cameras. There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Nikon COOLPIX P90 Digital Camera
Lens error CoolPix L11. I switch on the camera The lens comes out. A picture is shown for about 1 second. Then the message Lens Error is displayed. The lens is retracted. After 15 seconds or so the camera switches itself off. The camera was bought in USA as a gift for a friend in Sri Lanka. Not so easy to get a local repair - if this is at all possible anyway. What is your advice? Thanks James
Try the procedures in this tip. ... Nikon Coolpix 5700 Digital Camera
Lens comes out and then goes back in when turned on then I get a lens error message
Try the procedures in this tip. ... Nikon Coolpix S3000 Digital Camera
Lens doesnt come out gives message lense error restart camera
Try the procedures in this tip. ... Canon PowerShot SD1000 Digital Camera