Having problems with your Canon PowerShot A480 Digital Camera ?
I have a Canon power shot A480 that has a lens error restart camera?
What can I do to fix this problem?
This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have a Canon power shot A480 that has a lens error restart camera? What can I do to fix this problem?
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Canon PowerShot A480 Digital Camera
Lens Error! I dropped my camera on the floor, and now the lens wont open fully or close. The LCD says "lens error,restart camera." But even when I turn the camera off, it still happens. Its a Canon Power Shot A550. I need to find out how to fix my camera without breaking it some more.
Same problem. The lens is stuck in the zoom position. When the camera is turned on, the lens moves a just afraction like it want to fully open or close, then the camera beeps and prompts with the "Lens Error" Restart Camera. Solutions? ... Canon PowerShot A550 Digital Camera
I have a canon power shot A540 and can not get the lens to close. When I hit the power on-off button- it says Lens error-restart camera. What can I do to solve this problem. Thank you. Sue
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot A540 Digital Camera
I have A1100 Canon Power Shot ! it have a problem with lens , when I turn it on , it says :"lens error , restart camera ! " How can I restart it?
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Canon PowerShot A1100 IS Digital Camera
Own a Power Shot SX100 IS Canon camera. Camera won't work...am getting mesage, ¨lens error. restart camera''. When I go to the User Guide it tells me I need to contact a Canon Customer Suport Help desk as there may be a problem with the lens. I can't find contact information so am googling Canon and got this service. Can you help me?
Try the procedures in this tip. ... Canon PowerShot SX100 IS Digital Camera
When I turn on my camera (Canon power shot SD600) it won't come on... I get a series of three beeps then a message on the screen that says "lens error, restart camera." The problem is, I don't know how to restart my camera.
Take it to a proffesional... ull need a new lens and more likely a whole new camera but dont start buying until u ask someone that know ALOT about cameras anyway id have to see it up close to know wat excatly is worng. !!!! try cleaning ur lens !!!! ... Digital Cameras
When I turn my canon A630 Power shot on, it makes the sound as though it is coming on and the lens does not extend... All I get is a written signal in lower left hand corner of screen after about 5 beeps "lens error, restart camera. And the cycle begins again. Is there anything I can do to fix this?
Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Canon PowerShot A630 Digital Camera
Dropped my canon power shot a1000is...now lcd says lens error, restart camera (lens won't extend now)...Is this an easy fix or expensive?
HelloThank you for using FixYa for your problemZoom les is faulty. It should be taken to an authorized repair centre for a repair estimate. Very few digital cameras have any user-serviceable parts. ... Canon PowerShot SX100 IS Digital Camera
MY NEW CANON POWER SHOT SX1 IS DIGITAL CAMERA SAYS: LENS ERROR, RESTART CAMERA. THE LENSE WILL NOT COME OUT AND THE CAMERA WILL NOT STAY OWN. I DID CHANGE THE BATTERIES. CAN YOU FIND A SOLUTION FOR THIS PROBLEM? THANKS SO MUCH! NANCY IN TEXAS. email: [email protected]
The error "Lens error, restart camera" can be fixed by zooming in and out quickly a bunch of times. But the problem is that the lens itself won't come out. The book says that there may be sand or dirt in the camera lens and you need to send it to Can ... Canon PowerShot S3 IS Digital Camera
Camera model: Canon power shot SX110IS Problem: Shows lens error restart the camera
See http://www.fixya.com/support/r13011856-lens_error ... Cannon Digital Cameras
My Camera When I turn on my camera (canon power shot A420) the LCD screen is blank and reads 'Lens Error, Restart camera'. Can you please help me resolve this problem! Thank you
Try gently turning an knocking the cameras lens..i had the same problem an all it was,was the rubber protction guard had got stuck which is why the lens would not retract back into its position.so try twisting the lens gently or tapping it.well thats ... Canon PowerShot A420 Digital Camera
Canon Power Shot A430. Lens Error, restart camera. I've tried all the online fixes and am now at the taking apart stage. I can't get a definitive answer on what size/type of screwdriver I need. I have Phillips 00 & 0 and they are too big.
Bla ... Canon PowerShot SD500 / IXUS 700 Digital Camera
Lens error-restart camera on my canon power shot sd1000
Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Canon PowerShot SD1000 Digital Camera
Lens error I keep this Elph in a tiny, padded Halliburton case because the last TWO I bought ended up with broken screens. I never had a problem, though lightly used. Last night I recharged the battery and inserted it. Immediately upon power-up, the lens went out and I got a "Lens error, restart camera" error. I turned it on and off about twenty times, left the battery out overnight: same thing. I jiggled the lens with the same result. Canon tech support told me to take the battery out a
Lens mechanism has failed and a repair/replacement is the only solution- ... Canon PowerShot SD600 Digital Camera
Lens Error Pertaining to my Canon Power Shot A590 IS: when the power is turned on, I am receiving an "Lens error, Restart Camera" malfunction. I turned the camera off and back on; still same issue. I also removed the batteries; still the same issues. What is your recommendation?
This message appears when a malfunction in the lens occurs. It could be a grain of sand jamming a gear or a barrel out of alignment. In any case, the lens is not serviceable, you would need to take your camera to your nearest repair centre to have it ... Canon PowerShot A560 Digital Camera
I have a Canon EOS, 1000D which I purchased in Feb 09. I have an error message coming up on the screen everytime I take a shot (which doesn't record). The error is a Err 99, "Shooting is not possible. Turn the power swith to OFF and ON again or reinstall the battery." Which I have done and the problem seems (at this stage) to be fixed. Is it just a battery problem or is there someother problem with the camera it's self. SJ
I did some digging and found that this error is most often a lens communication error. Are you, by chance using a non-Canon lens?Try the following:1. Remove the lens and take a picture without any lens on. If you get an ERR ... Canon Rebel XS / Eos 1000D Digital Camera with EF-S 18-55mm f& EF 75-300mm f Lens
Lens problem I dropped my canon on a hard surface from about 2 feet. It will not close and I get the restart camera message... The lens are blocked and on the screen I have: Lens error...restart camera. What should I do ? I don't trust the services from my country and I wish to fix it my self but I need some help please ...
Sir this problem is most common one .but it needs to be done by\015\012sophisticated tools and well trained technicians.\015\012here whole lens system has been damaged.\015\012if lens(inner glass) is broken then it must be sent to a ... Canon PowerShot SD600 Digital Camera
I have a canon power shot sx110is camera. how do i restart it? an error message says "lens error restart camera."
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is t ... Canon PowerShot SX110 IS Digital Camera
I have a Canon PowerShot SD 870 IS and I dropped it 2 days ago. Now I'm trying to fix it. It's giving me an error that says "lens error, restart camera" How do i fix this problem?
Hold on to the lens while shutting down the camera. Repeat this till the lens is squared. Then restart the camera... try this a couple of times. Try not to force the lens too much. The key is to have the lens extended completely when on and lens squa ... Canon PowerShot SD880 IS / Digital IXUS 870 IS Digital Camera
I have a Canon Power Shot SX120 IS camera. I turned it on and the lens open a portion of the way and I got an error message that say, "Lens Error Restart Camera". I put fresh batteries in it this morning and have only taken about 10 pic's. I turned the camera off and removed the batteries then replaced with new ones but I still get same message. Please advise if you can.
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot SX100 IS Digital Camera
Lens error I tried to turn off my camera, (Digital Ixus 60) and the lens froze halfway closed. When I tried to restart the camera, an error comes up on the screen, saying LENS ERROR, RESTART CAMERA. I had this problem before on this camera, but while it was still under warranty. I sent it to be fixed, but now it seems the problem isn't fixed. Is there anything I can do now?
The only thing is, is that it is past it's warranty. THE WARRANTY ONLY COVERS DEFECTS, AND FACTORY ERRORS. \015\012\015\012IF THE LENS DOESNT GO BACK IN, THEY CANT FORCE IT AND YOU PAY THE FULL COST OF THE ENTIRE LENS BEING REPLACED AND T ... Canon PowerShot SD630 Digital ELPH / IXUS 65 Digital Camera
Lens error, restart camera for canon power shot SX120 IS
This is probably THE most common failure among digital cameras. There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Canon PowerShot SX100 IS Digital Camera
When i switch on my canon SD1100 camera it read like lens error, restart camera. the lens is out and can't get screw back. plse help cos i got to use this camera on my birthday. its a lens problem and please help me fix it back.
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Canon PowerShot SD110 / IXUS IIs Digital Camera
Canon Power Shot A590 IS lens error message won't
Sending it to an authorized cannon repair facility. the lens must be replaced. ... Canon PowerShot A590 IS Digital Camera
Lens error my canon IXUS 860 IS is having a lens error problem. firstly, the lens cant retract back and when i try to switch it on, the screen will say 'lens error, restart camera' so how do i restart the camera?? i'm currently overseas and although my camera is within warranty, i cant possibly send my camera back to the original country for repair. is there any DIY method?? i'm an amateur at cameras so i do not wish to try any method that may further make the problem worse. thank you for your h
This is probably THE single most common failure among digital cameras. There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Canon IXUS V2 Digital Camera