Having problems with your Canon PowerShot A490 Digital Camera ?
When I turn on my Canon Powershot A490 I get the "lens error - restart camera" msg. What do I do to restart?
This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My Canon PowerShot SD850 IS has a lens that is stuck in the extended position. I get a screen that says lens error, restart camera, but when I try to connect to the software, I get a screen on the computer telling me the computer cannot detect the camera. Battery is freshly charged, and I get the little yellow bird picture on the camera when I turn it on. It beeps about 4 times, and then turns off. Is there a safe way to get the lens to retract?
Don't play around with that lens, you can do more damage to the camera and focus with some of the stuff people tell you to try. Your camera just needs to be serviced and you'll be working great again. The shop that specializes in service for the powe ... Canon PowerShot SD850 IS Digital Camera
When I turn on my Canon Powershot A490 I get the "lens error - restart camera" msg. What do I do to restart?
Restart just means to turn it off and then on. That rarely actually works. Try these:\012\012Fixing a Lens Error on a Digit ... Canon PowerShot A490 Digital Camera
Lens problems I am deployed and I sent my camera to my wife and she has managed to brake it, I was hoping to get some help on this problem: When off, the camera lens is in the position as if it were being used. When turning the Canon Camera Powershot A530 on, the Canon logo screen comes on as it should. Following the blue logo screen is 2-3 rapid beeps made by the camera and a black screen is shown with the words, "Lens error, restart camera". Immediately after showing this screen for five
Try opening your camera, check the lens gear if its teeth are\015\012complete. If so, check if something stucks on it. Its much better to\015\012bring your camera to an authorized service center to re timing your\015\012lens track... ^_^ ... Canon PowerShot A530 Digital Camera
Lens Error I keep gettin lens error restart camera on my canon powershot sx100 and the lens wont retract. I have turned it on and off several times now. Is there anything i can do to get it working again?
Unfortunately this Canon SX100 (and the SX110 too) has a very fragile lens assembly. Once you have this lens error problem, there are only four solutions: 1) If it's under warranty, contact Canon to make it valid; 2) If not, then have a repair center ... Canon PowerShot SX100 IS Digital Camera
When I turn on my Canon PowerShot SX10 IS Camera, I get the message, "lens error, restart camera." How can I restart the camera?
That just means to turn it off and then on. Also, try these:\015\012Fixing a Lens Error on a Digital Camera\015\012 ... Canon PowerShot SX10 IS Digital Camera
I have a canon powershot SD 1000. The lense is stuck out. When I go to turn on the camera it says "lens error, restart camera". I don't know how to do this or how to get the lens back it. Help?
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Canon PowerShot SD1000 Digital Camera
Hi,Have got got a canon(powershot a710 is) whenever i turn on the camera i get a few beep noises and the screen remain black with the message'lens error,restart the camera'....and it then turns off.....I have not dropped it down.hoping someone would help me out with a solution. Cheers, Sanjana
The lens is jammed. Usually dust or grit gets in the mechanism and causes it to stick. Could try blowing down the side of the lens but it will probably need taking apart and cleaning. It is not an easy job to do but it might be worth trying as it wou ... Canon PowerShot A710 IS Digital Camera
I was taking photos when suddenly my Canon PowerShot SD 1300 IS IXUS 105 read "Lens error. Will shut down automatically. Restart camera." Then the screen went blank. The lens will not retract. I cannot do anything other than turn the camera back on and get the same message. I've never had this problem before.
There is something wrong with your lens barrel. It can be anything from some sand/dirt that got inside in which you try using some canned air to blow out the particles while continually turning it on and off. Usually what it is from is the camera bei ... Canon PowerShot SD1300 IS IXUS 105 Digital Camera
I keep gettin lens error restart camera on my canon powershot sx100 and the lens wont retract. I have turned it on and off several times now. Is there anything i can do to get it working again?
Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Canon PowerShot SX100 IS Digital Camera
I have a Canon Power Shot SX120 IS camera. I turned it on and the lens open a portion of the way and I got an error message that say, "Lens Error Restart Camera". I put fresh batteries in it this morning and have only taken about 10 pic's. I turned the camera off and removed the batteries then replaced with new ones but I still get same message. Please advise if you can.
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot SX100 IS Digital Camera
My wife dropped her Canon Powershot SD750 and we thought everything was OK. Then moments later when we tried to use it, the lens came out and then locked up and the screen showed 'lens error restart camera'. Since then, after numerous attempts to get camera to work, the camera still shows 'lens error' and the lens is always out and locked. Could you help?
HelloThank you for using FIXYA!!!This\012 is a suggestion. If you do not feel comfortable trying it, you will need to ... Canon PowerShot SD750 / IXUS 75 Digital Camera
Lens error When I turn the camera on it says "Lens error, restart camera," and turns itself off. When I turn it back on, the same problem occurs. The lens covers aren't completely closed, and the entire lens seems to be sticking out a little bit, like it didn't retract all the way. Please help! Thanks. Turn on the camera, camera shows a canon logo, then before turns off it said lens error, restart camera
\015\012\015\012I have a solution posted in doc "nikon s5 s6 lens cover error repair.doc" uploaded on site http://www.esnips.com/web/papputatiyasStuff&n ... Digital Cameras
Just purchased an powershot SX1 IS. I took one photo, zoomed in on it to see how clear the zoom was once taken a photo. THen it switched itself of with the lens still out. Now when turning it on it has a black screen and say lens error...restart camera. I have tried holding func. when turning on the camera and the time comes up on the screen. But as soon as I let go of func I get the error msg.
Hello if you just purchased this unit Then i advise you to take it back, this sounds like a system control issue or main board problem. Holding the function key while turning is factory reset, if this is not working right them the camera has a bad sy ... Canon PowerShot SX1 IS Digital Camera
I have only had my Canon PowerShot SD1400 IS Digital camera since December and all of a sudden whenever I try to turn it on, the lens does not open or move out and I receive an error message saying "Lens Error, Will shut down automatically, Restart camera." I have never dropped this camera and am concerned that it is not fixable. Please help!
It always comes because there is something loose inside the lens, such as a screw.\015\012These articles maybe helpful for you: ... Canon PowerShot SD1400 IS IXUS 130 Digital Camera
Canon powershot SD780 is camera. Camera shows the canon screen then turns black and beeps three times then says "lens error restart camera". I don't know how to restart...i need to use it I'm on a trip What do I do?
There's really no way to restart it if there's a physical problem with the lens. Try to power it on again but if that doesn't reset it, the camera needs to be serviced. A great site for help with these is: camerasandparts.com They just specialize in ... Canon PowerShot SD780 IS / IXUS 100 IS Digital Camera
Hey, my canon SD890 has a problem, it says "lens error, restart camera" when I turn on, and the lens stick out and won't get back to normal. Is there any restart bottom that can restart my camera?
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Canon PowerShot SD890 IS Digital Camera
I have a canon powershot sd750 and when i turn my camera on it says lens error, restart camera
Hi Shawn,Check the link below and you will be able to fix the issue by doing the troubleshooting.Click here - > ... Canon PowerShot SD700 IS Digital ELPH / IXUS 800 Digital Camera
Powershot A560 I have a Canon Powershot A560 but now when I turn it on it beeps 6 times and the screen shows "canon" in blue but then goes black and says at the bottom "lens error, restart camera". Also, then lens never fully goes in or out. Help.
The following blog outlines some repair options for a lens error. They won't work for all cases, but they're worth a try if the camera's no longer under warranty:\015\012\015\012 ... Canon PowerShot A560 Digital Camera
Hi, i have canon powershot a590 is ,and when i try to turn it on it says: " Lens error. Restart the camera", but i can't restart if i can't turn it on, maybe it happened because the camera run out of battery while it was on, please if you guys can help me out i would really appreciate it. Thank you very much.
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Canon PowerShot A590 IS Digital Camera
My daughters Canon PowerShot SD750 has the lens extended and stuck, turning on the camera gives a lens error message and atates to restart camera. have tried this numerous times and no help. Camera was never dropped, was just using one day, took some pictures, then the following picture I was taking lens stuck open.
Hi. This is an unfortunate mechanism failure. You can try to reset the micro board by removing the batteries for 3 mins. If that reset doesn't work, the actual lens sensor will continue ... Canon PowerShot SD750 / IXUS 75 Digital Camera
When i press the power button to turn on the camera, the lens does not come out as it should - I get a "Lens Error - will shut down automatically - restart camera" appear on the screen - My Camera is the PowerShot SD1400 IS Digital ELPH - I have only had this camera for a few months
See Lens Error ... Canon PowerShot SD1400 IS IXUS 130 Digital Camera
I put my camera in my backpack and the lens got stuck, it won't come out at all. When I turn the camera on it says "Lens error, restart camera". I've tried everything this site said to try but nothing has worked. My camera is a Canon Powershot A560. Does anyone know how I can fix it? Please Help!
Try these procedures. ... Canon PowerShot A560 Digital Camera
My canon powershot a590 camera lens is stuck. When I attempt to start my camera I get a message saying Lens Error Restart Camera then the camera immediately powers off.
Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Canon PowerShot S2 IS Digital Camera
Lens is open and won't retreat back inside. I turn the power on and makes a funny clicking noise like its trying to retract the lens back in. After three seconds of this it says "lens error, restart camera". Its a canon powershot SD790 IS digital elph with image stabilizer. Canon PC1261...don't know if that helps.
I've had similar problems with various versions of this camera. Here's the fix, if all else fails. These are step-by-step instructions to take apart and fix the camera's lens error. http://johnsmouth.wordpress.com/2010/12/01/lens-error/ ... Canon PowerShot SD790 IS/ IXUS 90 IS Digital Camera
My CANON Powershot A470 is giving me the following error message: lens error, restart camera. Ive tried multiple times. I turned it off for a few minutes, nothing happened. I removed the batteries and memory card for a few minutes, nothing happened. I shook it easily...nothing happened. I vacuumed the lens and tapped the lens...still nothing.
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Canon PowerShot A470 Digital Camera