Having problems with your Canon PowerShot A520 Digital Camera ?

When I press the ON button my camera screen lights up but the lense does not extend. The display system does not work either. It then does not turn OFF when I try but gives 3 little peeps and eventually turns itself off.


Answers :

Fixing a Lens Error on a Digital Camera
\012


\012

This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
\012

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
\012

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Repair Help & Product Troubleshooting for Canon PowerShot A520 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Ive had my Camara a while and I really wanted too take pictures today. But when i turned it on it said access, went in and out 3 times, and then said 'turn power off' Ive tried loads of things, such as; Giving it a little tap and pushing the lense, pulling the lense. and i i've even tried initalizing it so many time and that doesnt even work. Soo what am i suppost too do?


Change the batteries....make sure the card is sitting in it right...try these ... Digital Cameras

When I press the ON button my camera screen lights up but the lense does not extend. The display system does not work either. It then does not turn OFF when I try but gives 3 little peeps and eventually turns itself off.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Canon PowerShot A520 Digital Camera

My pentax optio E70L has just started giving me trouble by not staying on when I try to turn it on. I checked the batteries and they seem to be at full capacity I just get pass the first screen and then a little bit of the camera view and then it turns off but the lens stays open. Pleaswe help


Fixing a Lens Error on a Digital Camera This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart ... Pentax Optio E60 Digital Camera

My Canon EOS Digital Rebel XTI will not automatically focus. The little AF points don't show red to signify it is focusing. The camera just takes a blurry picture. It was working perfectly one minute and the next it wasn't. I tried taking the battery out and the points would turn red a few times then they would quit working again. Please give me an idea what might be wrong. Thanks,


Does the lens have an AF / MF switch on it, if so ensure it is on AF ... Canon Rebel XT / EOS 350D Digital Camera

Broken? I got My DXG-305V a few weeks ago, and it acting wierd. I plugged it into my computer to get a few pictures off, then I safely removed it, and tried to turn it on, but it wouldn't. The little power light will turn green for a second and then turn red. I have changed the batteries, tried removing the memory card, and tried plugging it back into the computer, but nothing will work. Does anyone know what is wrong?


Have a look in the battery compartment to see if the connections for the battery is not connecting with one of the batteries, i had a camera that stop that stop working on batteries but ok with the mains. ... DXG Technology DXG-305V Digital Camera

I cannot turn the camera on. I guess it was dameged during my holidaying. I recall that, the camera was excidently turned on inside its holder and as the mechanism tried to push the lense out from the body it was blocked by the bag holding the camera. Now, when I try turning the camera on, the lense could not move forward at all. It gives cracking noises and turns itself off. Could this problem be fixed or better to buy a new camera? Arthur


If your camera isn't under warranty, I think that it has no worth to repair it by the after-sales.\015\012But you can try to fix it by your self, anyway there will be no loss for a bad camera.\015\012May be this post will be any helpful: ... Pentax Optio 60 Digital Camera

The zoom won't come out when I try to turn my camera on, it just turns a little bit, then turns back to the original place, and the screen says zoom error. I've tried different batteries, and taking out the memory card and putting it back in. The model is FujiFilm; FinePix A400. What should I do?


Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. O ... Digital Cameras

I have a samsung L200 digital camera. It was working fine until my 2 year old little girl decided she needed to play with it. Not sure if she done something or not but now the camera will not work. When I try to turn it on the power button lights up but that is all that happens. The screen does not come on or anything else. Also the lens seems to be stuck and will not go back in. And I also just noticed that the power button will only turn the camera on but will not turn it off. I was trying to


Sounds like she may have dropped it and caused a lens problem. I don't know how much damage you've done so far in attempting to disassemble it but, if you can, put everything back and try the following:\012\012 ... Samsung L200 Digital Camera

Error Message Hello! Every time I turn My Sony camera on it starts beeping and and giving me the error message "Turn the power off and on again." I've tried turning it off and back on, along with taking the battery out and putting it back in and even pressing the reset button and I'm still continuing to get the same error message. Any ideas on what I can try next?


I have the same problem ... Sony Cyber-Shot DSC-L1 Digital Camera

I have a Nikon S6 digital camera, everything about the camera seems to work fine, except for this "lens error" message I keep getting. Sometimes I'll turn it on, and I can use it just fine. But then there are other times where I have to turn it off and on in order to get it to work. And then there are those times where turning it off and on don't help. I usually give up and try again later. Sometimes it'll still give that error message, and other times, it will just work like normal. What can


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Nikon COOLPIX S6 Digital Camera

Zoom broken my camera was on then bed & the zoom was out to normal level. i tripped and fell on it & now the inner bit of the zoom is wedged at an andgle and wont move. i tried turning the camera on to see if it could move it at all itself and the mechanism tries 5 times then gives up and the camera turns off without turning the screen on. Does this sound fixable as i only got it xmas '07 and my dad never took out the insurance. If yes any ideas where I could take it/send it to get it fixed? I l


The impact damaged has jammed you lens assembly. I see these all the time in my shop. If it can be repaired without parts a shop should be able to do it for you for around $75. If it needs a new lens however it will not be worth the cost (the part ... Olympus FE-210 Digital Camera

Cybershot will not power up it has been charged and i tried removing the sd card and battery then reinstalling them and still no power. It tried to turn on but shut down. Its giving the error messag too Turn off and turn back on!!! and when it does nothing.


... Sony Cyber-shot DSC-W170 Digital Camera

No matter what I do, my camera keeps giving me a "Battery Depleted" message whenever I try to turn it on. It's a Pentax Optio E40, and I've only had it a couple of weeks. It was working fine, but then one day when I tried to turn it on, I got this error. I replaced the batteries, but the error still came. I've checked the orientation of the batteries, tried re-inserting them, etc, but nothing seems to work. Please help! Thank you!


I had the same problem and checked the manual. If you haven't used the camera in a while and there were either no batteries or dead batteries in it, put in new batteries, keep it off, and WAIT a few minutes. Then try to turn it on. This helped with P ... Pentax Digital Cameras

My camera fell on my floor when I was trying to film a video. Now it is stuck with the lens out, and when I try to turn it on it makes a weird noise, stops, makes it again, makes a new 'bloop' powering off noise, and that's it. I can click the little play button in the square to view my pictures and it will make noise and turn on and I can go through my settings but it will not let me switch to actual camera/video mode! What do I do?


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Samsung SL605 Digital Camera

Hi i have a olympus fe-330 camera- try turning on . the lens come out screen blank ,trying turning off lens dont move giving sound when tryind to push on/off button


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Olympus FE-330 Digital Camera

My C1030 digital camera, which I bought at the end of december 2010, is having a major problem. The lens won't close anymore and when i try to turn it on, it makes a strange noise and it gives a black screen and turns off and still the lens won't get in, it stays out. I tried new batteries, but that's not the problem. Please advise.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... BenQ DC C1030 Eco Digital Camera

Lens trouble My lens will not come out entirely on my camera, for when I push the button to turn it on, the lens tries to completaly come out but then quickly retracts back halfway and remains stuck about halfway open. The screen is black and the light flashes red everytime I turn on the camera, along with a noise of something stuck. I have tried using that little button that someone told me was the reset button, along with plugging it in, and charging it. None of this has helped me with fixing


Appears to be a repair issue... lens track may be off ... Olympus FE-280 Digital Camera

3 beeps One day my camera was working fine. The next day, I tried to turn it on and the lens came out just a little and then it stopped and beeped three times. It now makes this noise everytime that I try to turn it on. It did this before when the lens was uneven. However, the lens appears to be in proper place so I don't understand why it is doing that.


After some attempts to turn on the camera following the instructions posted in this page, i just bang the camera when y press the start button, and the lens was released, and the camera start up with no problem :) ... Samsung Digimax D53 Digital Camera

Lens error I have a Canon Powershoot SD1000 and it was working fine until one day the lens stopped retracting. Now it doesn't retract and I get a Lens Error, Restart Camera message. I looked at other websites to get help and tried some of the ways they suggest to fix it. Not sure if its working, because it still gives the same message and makes a noise sounding like its trying to retract then gives me the Canon welcome picture. I've only had this for a little over a year and would like it to be


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Canon IXUS V2 Digital Camera

My K7 will turn on but the LCD screen and monitor won't turn on. The only thing that shows up on the LCD screen is the battery button. When I try to take a picture it makes a funny noise. I didn't drop my camera or anything and it worked perfectly yesterday. The only thing is that I did charge my battery overnight. It still turned on normally earlier in the day but then I didn't take any pictures (as my daughter wouldn't look) so I turned it off until a little bit ago when I turned it on and dis


... Pentax K7 Digital Camera

I dropped my Sony Cybershot DSC-H50 and now the lens won't come out. It turns on and all but it just tells me to turn it off and on again, and it won't let me look at the menu. the circles in the lens are closed and it's pitch black looking at the screen and I tried pressing the shutter button once I turn it on and it just says to turn it off and on again. Also 2 times this occurred, when I could see with it but everything was still blurry and the lens opened up a little but just those 2 times.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is t ... Sony Cyber-shot DSC-H50 Digital Camera

Kodak easyshare z712IS. sounds like a typical problem but...I try to turn it on, lens only comes out a little bit, then it turns off. I replace the batteries and the set time and date comes on...I set time and date camera turns off. I CAN in fact view pictures in the gallery but as far as taking pictures....nothing.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Kodak EasyShare Z712 Digital Camera

Installing camera hi..i have a question. i dont know if yall are who im supposed to ask, but im going to give it a shot. okay, so i have a i634 polaroid digital camera. well, it has worked fine for the last month..now all of a sudden, when i try to bring it up on the computer to get my pictures, its saying that it isnt hooked up right or its not turned on...it is turned on and is hooked up right. usually as soon as i turn my camea on, it will automatically say *new hardware found*, but its not d


My batteries are fully charged,but my camera is makeing a beeping noise like thier not charged and it always used to tell me to replace the batteries and now it dosent ,it just wont turn on.what do i do? ... Digital Cameras

The entire zoom lens will not come out when I turn the camera on. It moves a little, makes a sound, and then my camera says turn off camera off and back on. I tried that several times and it is still not working. The battery is charged. I did go to the beach and wondering if sand got into the camera. I also cannot review my pictures as the message comes up about turning it off. What is the best solution?


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Panasonic Lumix DMC-TZ3 Digital Camera

We have a Sony Cybershot DSC-W1. When we turn the camera on it fails to start properly. The lens moves a little, it beeps 18 times and then displays "Turn the power off and on again". We have tried changing the batteries, but it has made no difference. When we turn it off it moves the lens, but does not bring it fully back. Any tips appreciated.


Goto http://www.digitalcamrepair.com/self_diagnosis_page.htmfor self diagnosis.please let me help you before leaving a bad feed back. ... Digital Cameras
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2570 seconds