Having problems with your Canon PowerShot A560 Digital Camera ?

My lens (zoom portion that extends) is stuck in the outward position. How can I get it to retract and lens cover close?

Answers :

Fixing a Lens Error on a Digital Camera
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Canon PowerShot A560 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My lens (zoom portion that extends) is stuck in the outward position. How can I get it to retract and lens cover close?

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot A560 Digital Camera

Hi my son dropped my digital camera while the lens was extended and now it wont retract and it says zoom error also the shutter wont open fully or close, the lens is at a slight angle and wont budge do i have to take it to get repaired or can i pull it apart myself thanks

HiIt helps to know the make and model of the camera, some cameras the lens is too fragile and we have never been able to repair them. Other models we have had a great deal of success repairing them. (Google: darntoothysam)One ... Digital Cameras

Lens doesn't retract when cover hits it. Only way to get lens to retract is to take out battery, put it back in, and then the lens slooooowly retracts, but will bounce back out if cover is closed quickly...Going to Europe in 2 days..should I buy a new camera???

The original problem was a camera with jammed lens mechanism or faulty lens motor. I think the camera had been replaced.The following post is directed to new users following up on this thread, as the original problem had already been sort ... Olympus Stylus 400 Digital Camera

Camera was on, working fine. When powering off, telescoping lens did not retract so lens remained extended just a bit with lens cover open. Waited a few minutes, turned it back on and I get the "access" display message then the beeps and (turn power off and back on) message. While off, I have removed the battery, replacing it with a fully charged spare and it still does this. The lens tries to telescope a little bit and retracts a touch, but I can't get the camera out of this mode. Can it be res

Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Sony Cyber-shot DSC-W55 Digital Camera

I have a dscw180 and we took it to the beach. I think there is a little sand in the lens cover and the cover will not close. The lens extends and retracts but has no protection when retracted. Any ideas?

Try blowing the sand off with a can of compressed air. ... Sony Digital Cameras

Nikon coolpix 5000 zoom lens is stuck in extended position when battery died. replacing battery I now get error message: Remove lens cap. but the cap is off- I cant get the lens to retract.

... Digital Cameras

Zoom error My lens is zoomed out and closed... I am unable to open it. When I turn on the camera, a zoom error appears on the screen. What can I do to get the lens to retract and be able to take pictures again?

I had the same problem with mine and I tried several suggestions, BUT the only one that has worked is to gently grab the lens, pull it out as far as it will go until fully extended. While keeping it extended turn the lens to the right until you hear ... Fuji FinePix E550 Digital Camera

Zoom error Lens stuck in the halfway-out zoom position (lens cover is closed)and I am getting the "zoom error" message.i try to 1.turn off/on again but not ok 2.take battery off for 1 hour but not ok 3.Changing new batteries but not ok please give me how this problem was solved by my self. thank you... (i had bought camera about 3 years .my camera ever sent to dealer because same ploblem about 3 time)

I had sent my camera in for the same issue and they did nothing to help with it. Seems to happen when battery gets low or dies, lack of on-screen battery meter doesn't help. Typically have to manually twist the lens to close it or open it after fresh ... Fuji FinePix E550 Digital Camera

My Kodak M853 does not turn on and off as it did when new. the lens extends and retracts slow and the lens cover opens and closes slow, sometimes not closing at all. This happens under all battery conditions.

1. Clean the battery contacts. a. Remove the battery/batteries and the memory card from your camera, then wipe the battery contacts with a soft, clean cloth. b. Reinstall the battery/batteries into your camera. Please make sure that you are installin ... Kodak EasyShare One Digital Camera

When I turn the camera on, the lens cover opens and then closes. When I turn the camera off, the lens cover closes and then opens. So, how can I get the timing of the lens cover correct? Or can you tell me how I can keep the lens cover open all the time? (not the best solution but now I can't take a photo at all!)

Good\012 day,This is a common problem and sometimes can be fixed.Please\012 see details on my tip on how to fix this error here: ... Pentax Optio E10 Digital Camera

I have a small Panasonic Lumix DMC-TZ5 camera. After fully charging the battery I am all of then sudden getting this error message :"please turn camera off and then on again." When the camer is OFF the lens is extended and open. When I move the camera to ON the lens moves in to the closed position closes, then reopens, extends, tries to focus, is unable to and the error message appears "Please turn camera off and then on again" This cycle just repeats. The lens is able to extend it is not st

Hi,Checkout this tip about digital camera error messagesLens Errorfix for Digital Cameraheatman101 ... Panasonic Lumix DMC-FZ7 Digital Camera

My Canon PowerShot SD850 IS has a lens that is stuck in the extended position. I get a screen that says lens error, restart camera, but when I try to connect to the software, I get a screen on the computer telling me the computer cannot detect the camera. Battery is freshly charged, and I get the little yellow bird picture on the camera when I turn it on. It beeps about 4 times, and then turns off. Is there a safe way to get the lens to retract?

Don't play around with that lens, you can do more damage to the camera and focus with some of the stuff people tell you to try. Your camera just needs to be serviced and you'll be working great again. The shop that specializes in service for the powe ... Canon PowerShot SD850 IS Digital Camera

Lens cover Even when I slide the lens cover open as far as it will go, the camera lens does not extend and the camera still says "lens cover" closed.

Well, I just looked at one, it is not easy to get to the front cover. Everything is removed from the back of the camera. The display, both circuit boards and the battery compartment have to be removed first. You may do better locating another cam ... Fuji FinePix 2650 Digital Camera

Camera model SL620. Lens cover does not automatically fully retract. A small portion blocks the top and bottom of the lens but will retract if touched. Tried blowing dry air on the cover and wiping with a soft cloth.

Apparently the lens has had some kind of impact to cause the lens cover to be bent a little. What happens is that the lens cover holder , or ring, on the end becomes bent or misshaped to a degree. This then causes a binding effect on the diaphragm as ... Digital Cameras

Sony camcorder HDR SR11 auto lens cover will not close I keep getting message (Lens cover open please power down). I can hear the motor trying to close. Thanks

... Sony Digital Cameras

Zoom error The lens extends to maximum and motor keeps running when camera switched on, then lens retracts to about an inch then the screen says Zoom Error, also the zoom control doesn't work then. and there is no picture. Pictures already stored in camera can still be seen. But it seems there is something wrong with the zoom setting.

HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will ... Fuji FinePix S8000fd Digital Camera

When I turn it on, there is clicking and then a lens error. The lens cover stays open. I removed the battery and put it back in, and I still get the lens error, bu the cover closes when it shuts off. When I turn back on, clicking and lens stays open as before.

HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is t ... Nikon Coolpix S210 Digital Camera

I have a cannon camera, my boyfriend dropped it with the lens extended and now whenever I try to turn it on I get a message saying that there is a lens error and the camera will shut down. I have tried a couple of answers on this website, but most have to do with a lens that is stuck out, mine will still retract back and forth if you smack it on your hand. My problem is when you power it off and back on the error shows up and the lens will not extend then. Any suggestions are greatly appreciate

... Canon PowerShot SD1300 IS IXUS 105 Digital Camera

Lens Errors The Lens on my EasyShare C330 will not retract. Going through the various options yields both lens errors 14 and 22. Tried tapping the bottom. While that triggered descriptions of each option (sports, video clip, etc), it did not trigger the lens cover closing or retracting. Any suggestions?

To all new users posting on this thread:When the lens will not retract and camera is not functional (no picture on\015\012display, and does not shoot) , and you already tried replacing\015\012batteries with a new fresh set (ensure please) ... Kodak EasyShare C330 Digital Camera

Lens error The lens on my Sanyo VPC-E760 will not close. I was not dropped, I was using it to take a picture and turned it off, but the lens never retracted. Now when I turn it back on, it is stuck in zoom mode and give an lens error message when I try to zoom back out, then it shuts itself off. Battery is fully charged. Any suggestions?

Hey jennbrady24,\015\012 What is most likely causing the lens error is that something is obstructing the movement of the lens (i.e. sand). I would first try removing the batteries and the memory card and waiting at le ... Digital Cameras

Sony DSC-S500 My camera is 10 months old. It's been working perfectly up until today. When I turn it on the lens closes. When I turn it off the lens opens. When I can get the lens to open half way as soon as I push the zoom button it closes. It's kind of like the lens is stuck. I've tried replacing batteries, I wasn't sure what else to do.

You are right it has defective mechanism,  a stucked mechanism is present. camcorder are smart it can detects error and shuts down itself for safety. earlier models dominoes the defect if the user is not quick enough to react when something goes ... Sony Cyber-Shot DSC-S40 Digital Camera

When I turn the camera on, the lens extends, makes a few noises like it is trying to retract the lens. The viewer shows nothing - like the lens cover is on. When I push the power button to shut it off, it makes the noises again and shuts off but does not retract the lens. The battery is fully charged.

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Olympus FE-220 Digital Camera

Kodak DX7440 Lens Cover does not open or close properly

Thank you apr 22 guest! i got a fiberless cloth to place over the lense while i fiddled, first with my tweezers then with my plastic toothpick (from the swiss army knife! yay mcguyver!) and after fiddling a bunch with the top fan (which was partially ... Kodak EasyShare DX7440 Digital Camera


I know this is not the answer you want, but when you dropped the camera you damaged the lens tube (housing) and your camera will require professional repair. ... Digital Cameras


Afraid as a physical fault it would only need to be services to get it working again. A local camera store should be able to help. ... Digital Cameras
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3054 seconds