Having problems with your Canon PowerShot SD1100 IS Digital Camera ?

When I turn my camera on, I get a message that says, "Lens error, restart camera," but everytime I restart it, I get the same message.


Answers :

Fixing a Lens Error on a Digital Camera
\012


\012

This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
\012

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
\012

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Tap it on something with the lens facing down do so gently sometimes it will free it up it just gets jammed up sometimes
Repair Help & Product Troubleshooting for Canon PowerShot SD1100 IS Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I turn my camera on, I get a message that says, "Lens error, restart camera," but everytime I restart it, I get the same message.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Canon PowerShot SD1100 IS Digital Camera

I have a Canon Power Shot SX120 IS camera. I turned it on and the lens open a portion of the way and I got an error message that say, "Lens Error Restart Camera". I put fresh batteries in it this morning and have only taken about 10 pic's. I turned the camera off and removed the batteries then replaced with new ones but I still get same message. Please advise if you can.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot SX100 IS Digital Camera

When I turn on my camera (Canon power shot SD600) it won't come on... I get a series of three beeps then a message on the screen that says "lens error, restart camera." The problem is, I don't know how to restart my camera.


Take it to a proffesional... ull need a new lens and more likely a whole new camera but dont start buying until u ask someone that know ALOT about cameras anyway id have to see it up close to know wat excatly is worng. !!!! try cleaning ur lens !!!! ... Digital Cameras

I turned on my camera to show some friends some pictures i took and i'm getting a message that says lens error, restart camera. when i restart nothing happens and the lense it extended out. how can i fix this? i am in a remote location in costa rica and won't be able to bring it to a shop. thanks. leela


The motor that dirves the lens must be stuck , just take it to the service center to get it fixed ... Canon PowerShot SD1000 Digital Camera

My Canon PowerShot SD850 IS has a lens that is stuck in the extended position. I get a screen that says lens error, restart camera, but when I try to connect to the software, I get a screen on the computer telling me the computer cannot detect the camera. Battery is freshly charged, and I get the little yellow bird picture on the camera when I turn it on. It beeps about 4 times, and then turns off. Is there a safe way to get the lens to retract?


Don't play around with that lens, you can do more damage to the camera and focus with some of the stuff people tell you to try. Your camera just needs to be serviced and you'll be working great again. The shop that specializes in service for the powe ... Canon PowerShot SD850 IS Digital Camera

Lens error, restart cameraI turn on my camera, and I get an error message stating Lens error, restart camera, the lens is open and will not retract, I have removed the battery and tried to restart. It will not go beyond the lens error message


This is probably THE most common problem with digital cameras. Try these procedures. ... Canon PowerShot SD850 IS Digital Camera

Lens error, restart cameraI turn on my camera, and I get an error message stating Lens error, restart camera, the lens is open and will not retract, I have removed the battery and tried to restart. It will not go beyond the lens error message


Try these procedures. ... Canon PowerShot SD850 IS Digital Camera

Lens Error. Everytime I turn my camera on I get a message on my screen saying that I have Lens Error. The product doesn't contain any physical damage nor accidents.


I've had this camera for 2 years and have had some problems as well.The lens error message has happened to me twice, and 1 out of the 4 small buttons wont work so I cant see the pictures I have taken. I have also had to exchange it two times because ... Nikon Coolpix S600 Digital Camera

I have a canon power shot A590 they dont make them anymore everytime i try to turn it on it says lens error restart camera ad when i do it says that again i dont know what to do. What do i do that doesnt involve sending it back or getting a new one?


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot A590 IS Digital Camera

When you try to turn on camera you get a message saying lens error, restart camera


It shows that the System Control Section got faulty needs to be fixed technically, i advised to take it to the nearest cannon service center for assistance. Good Luck ... Canon PowerShot SD850 IS Digital Camera

I have a canon ixus 900Ti. I turned it on yesterday and the lens came out as normal. when i went to take a pic the camera shut off but the lense never retracted. when i turned the camera back on the splash screen came on, followed by a series of beeps and then and error message saying "lens error, restart camera". restarting has not solved the problem. its like the lens is stuck out. hope you can help Regards Liam


Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Digital Cameras

When I turn on my camera, It tells me Lens error and that I should restart my camera. Don't know how to restart it except turn it off and I get the same message. The lens doesn't go back in when I turn it off. Pleasr help. I have a wedding this weekend thank you sue


Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. O ... Canon Powershot A2000 IS Digital Camera

When I turn on my camera It tells me Lens error and that I should restart my camera. Don't know how to restart it except turn it off and I get the same message. The lens doesn't go back in when I turn it off. Pleasr help. I have a wedding this weekend thank you sue


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is t ... Canon Powershot A2000 IS Digital Camera

Lens error, restart camera telephoto lens is stuck in zoom position and won't retract, so when i turn on camera, screens says "lens error, restart camera", but it won't restart...just keep coming up with same error message


Hello mnickoliThis is a fairly common error especially with the A560.This either means that something is jamming the lens , or that the\015\012lens sensor is faulty. This is a very , if not the most common problem\015\012with modern digit ... Canon PowerShot A560 Digital Camera

Lens Stuck My Lens is stuck on my Coolpix S200 and I'm getting the Lens Error message. I tried to push it back in like I read on here and it went partly in and now its completely jammed. I've only had my camera for about 4 months. Please help!! I'm hoping to fix it myself. i dropped my camera and now the lens wont come out. Everytime i turn on the camera it tells me to turn it off then on again. I've done it multiple times and it doesnt work. I tryed to push the lens in and out but it doesnt ma


YOU CANNOT REPAIR THIS SOPHISTICATED CAMERA YOURSELF!!\015\012I guess pushing the lens inside may have made the problem worse.\015\012I follow a rule- if you drop an electronic equipment and a problem occurs- it usually takes a profession ... Sony Cyber-shot DSC-S700 Digital Camera

Lens Error Hi, When I turn on the camera, it says "Lens Error. Restart Camera." When you restart the camera, it gives you the same message. The Canon zoom lens will not go back into the camera. Help!


If you are sure that your battery is fully charged but still does not do any good, then do this little trick:1. Hold the camera on your right hand with the lens facing the ground.2. As you press the power on button, tap or hit ... Canon PowerShot A550 Digital Camera

Lens error My zoom will not work. I can take pictures if I don't zoom, but as soon as I try to zoom in, the screen goes black, the camera beeps a few times and a message that says "lens error, restart camera". However, upon restarting the camera, nothing changes - it still won't zoom!. Also, when turning on the camera, when the lens first comes out...it sounds funny, like it is puttering. Help?


Powershot S3 IS: lens error message, lens juddering on startup but not \015\012coming out. Tried all tricks on internet without success, so decided to \015\012dismantle camera. Localised fault to optical position encoder on first \015\012transfer gea ... Canon PowerShot S3 IS Digital Camera

It keeps saying i have a lens obstruction and to restart camera. and i do but i get that message everytime. and i didnt drop it, how can i fix it?


... GE A1455 Digital Camera

Lens error, restart camera is the error message I get when trying to turn on the camera. The lens will not fully extend and just starts to wiggle back and forth then I get the error message when the screeen gos black. help!


Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. O ... Canon PowerShot S3 IS Digital Camera

Hi! Im Michelle from Dubai UAE, i bought my canon elph series camera last july 09 only and just yesterday after turning on the device the lens was stock up and not turning to its place anymore,.i tried to turn it off and on again but the camera is only blinking and there's a message on the screen says "Lens error, restart camera" ...I would realy appreciate any positive feedback,..Thank you very much for your kind attention Sincerely, Michelle Email:[email protected]


Hello.....\015\012sir it might be a lense problem i guess............the spring with which lense moves may be not proper............. slidin of lense is not aceessble by ur cam...........so better if show it to ur provider.......they replace it ... Canon Elph Jr. APS Point and Shoot Camera

The lens on my sd600 won't open when I turn the camera to picture taking position. Screen goes black and message says ''lens error, restart camera''. I have to go back to view mode and then turn camera off and on again in order for partially opened lens to retract fully and close.


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Canon PowerShot SD600 Digital Camera

When i try to turn my camera on it says "lens error, restart camera" but when i try to restart the camera it just repeats the error message. Ive plugged the camera into the computer, I've tried taking out the battery and memory card nothing changes. the lens will not extend or open"


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you wi ... Canon PowerShot SD1100 IS Digital Camera

I took my camera to the beach, took a picture and put it back in my bag. I then took the camera back out to take another picture the lens extended but then it went back in again it went to go back out but stopped and a loud beeping noise started and a message saying lens error restart camera. I don't know how to restart the camera and if that means turning it of then on it still doesn't work. What can I do now?


If your camera went into "standby" mode, the lens retracted and you may have thought it was off. You put it into the bag and slight pressure on a button reactivated it and the lens tried to come out but may have been prevented by something in the bag ... Canon PowerShot A480 Digital Camera

Lens error when i turn off my camera, the lens fails to retract and i get a screen that says, lens error, restart camera. Can anyone explain this. When i try to turn cmera off/on the lens remains extended. It does take pictures.


On Fathers Day, 2006, I received a Canon PowerShot SD700 IS, and it has served me well. Just before Father's Day, 2012, my young son dropped my precious PowerShot on its lens onto a wood floor, causing the smallest ring at the end of the lens assemb ... Canon PowerShot SD700 IS Digital ELPH / IXUS 800 Digital Camera

Hey, my canon SD890 has a problem, it says "lens error, restart camera" when I turn on, and the lens stick out and won't get back to normal. Is there any restart bottom that can restart my camera?


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Canon PowerShot SD890 IS Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5212 seconds