Having problems with your Canon PowerShot SD1400 IS IXUS 130 Digital Camera ?

It wont turn on because the lense is stuck - Canon PowerShot SD1400 IS IXUS 130 Digital Camera


Answers :

Fixing a Lens Error on a Digital Camera
\012


\012

This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
\012

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
\012

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Repair Help & Product Troubleshooting for Canon PowerShot SD1400 IS IXUS 130 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It wont turn on because the lense is stuck - Canon PowerShot SD1400 IS IXUS 130 Digital Camera


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Canon PowerShot SD1400 IS IXUS 130 Digital Camera

My cannon powershot sd1400 wont turn on - Canon PowerShot SD1400 IS IXUS 130 Digital Camera


Try the procedures in this tip. ... Canon PowerShot SD1400 IS IXUS 130 Digital Camera

I have only had my Canon PowerShot SD1400 IS Digital camera since December and all of a sudden whenever I try to turn it on, the lens does not open or move out and I receive an error message saying "Lens Error, Will shut down automatically, Restart camera." I have never dropped this camera and am concerned that it is not fixable. Please help!


It always comes because there is something loose inside the lens, such as a screw.\015\012These articles maybe helpful for you: ... Canon PowerShot SD1400 IS IXUS 130 Digital Camera

I have a canon powershot A470 and it fell in water. after i removed the card and batteries of which still worked and neither were wet, i let the camera dry for a couple of days. it has turned on since and the screen would come on and show me the pics on the card but it kept turning itself off and the zoom lense would go in and out on it's own. now, i can't get the camera to turn on and the zoom lense it stuck. any ideas??? or should i call it a wash. i really love this camera!!! Theresa


I submerged my powershot for a couple of seconds. it did get completely wet. it was acting very strangely: the lcd wasn't working, the little orange light on the front kept flashing, and it took a few tries for the lens to extend.then ... Canon PowerShot A470 Digital Camera

Canon powershot sd1400 is e32 error? - Canon PowerShot SD1400 IS IXUS 130 Digital Camera


The problem is related to the mechanics in the optical image stabilization. There are 2 plastic ball bearings inside the shutter/lens module that can pop out of their round holders that are held in by 2 springs. This can occur by simply dropping the ... Canon PowerShot SD1400 IS IXUS 130 Digital Camera

I have a Canon Powershot Digital camera just over 1 year and we turned it on the screen is all black now(started out 1/2 black-it flashes but no picture is taken- all settings are as they have been since we bought this camera from BestBuy. This is the 2nd Canon Powershot we bought in the past 3 1/2 years & it will be the last one. Can you tell me what I can try to get this fixed? Thank you. Karen from NC


Test ... Canon PowerShot A85 Digital Camera

My Canon digital Camera won't turn on - Canon PowerShot A570 IS Digital Camera


I assume you've already gone thru the obvious check and proposed fixes covered in the user manual (battery replacement, contact cleaning, etc). I did all that to no avail after dropping it about 1m onto a concrete floor last nite - after which it re ... Canon PowerShot A570 IS Digital Camera

I have a canon powershot s5o, and the other day i turned it on,was going to take a photo and appeared E18. it turned off but the lense of the camera did not go inside the hole and cannot close it.. i try to turn it on and appears the first image,and immediately whites stripes on the blackground. and try again and the same. the lense is stuck there i cannot close the thing that covers the lense


... Canon PowerShot S50 Digital Camera

I was Importing some pictures to my computer from my Canon sd 1300 is powershot digital camera , When the Battery died , I was not in the room at the time , So I came back in and attempted to turn the camera on and it said "Please change the battery pack" which means I need to charge the battery , and When the camera shut off , The lens did not close . SO I charged my battery , and the next day , I put the battery back in the camera like normal and I turned it on , and on the screen it said "Len


Since your camera is new the priviledge of your warranty claims must not be lost. So do not tamper to lose this benefit but call up the call centre of Canon for registeration/advice. What you can do is to remove the battery and keep if off . Since th ... Canon PowerShot SD1300 IS IXUS 105 Digital Camera

Troubleshooting problems I have a canon powershot s60. I tried to take a picture earlier and the screen is completely white. The camera turns on, the battery is fully charged and there is nothing wrong with the digital card. THe camera wasn't dropped nor did it get wet. I keep trying to turn it off and on, but all I get is a white screen. No images. But there are 900 images on the camera card and i just used it this morning. Please help. Thanks, Shannon


Take a picture with the camera and download it. If the pictures also shows up white then this probably is a defective CCD imager. If so, Canon should fix this for you for free, including free shipping both ways. This is regardless of your camera's w ... Canon PowerShot S60 Digital Camera

Canon PowerShot S3 IS Digital Camera turn on


Get your camera serviced imediatly.. ... Canon PowerShot S3 IS Digital Camera

My canon powershot A480 wont turn on - Canon PowerShot A480 Digital Camera


... Canon PowerShot A480 Digital Camera

Canon sd1400 change the battery pack - Canon PowerShot SD1400 IS IXUS 130 Digital Camera


... Canon PowerShot SD1400 IS IXUS 130 Digital Camera

My Canon PowerShot G9 won't turn on. - Canon PowerShot G9 Digital Camera


You probably have a loose screw in the camera which caused a short and no power. It's a common thing on your camera until corrected. Try this website: www.camerasandparts.com They just specialize in the canon powershots and they're wonderful if you ... Canon PowerShot G9 Digital Camera

Turn off the canon powershot s50 - Canon PowerShot S50 Digital Camera


... Canon PowerShot S50 Digital Camera

Canon powershot sd960 is digital camera 12.1 mega pixels. When you turn on the camera, you see the initial canon greeting, then the screen in black and when you take the picture it is black. When you review pictures from SD card, you see the rev images but the new ones do not show up but black.


Hi,\015\012\015\012This may well be an internal comonent failure or a problem with the SD card. However, to troubleshoot this issue, first remove both the SD card and the batteries altogether from the camera. Replace both, power up and se ... Canon PowerShot SD960 IS Digital Camera

Lense error 21 on VPC-E760 digital camera - Canon PowerShot SD600 Digital Camera


This is probably THE most common failure among digital cameras. There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Canon PowerShot SD600 Digital Camera

My canon powershot sx130 won't turn on - Canon PowerShot SX130 IS Digital Camera


... Canon PowerShot SX130 IS Digital Camera

Canon SD400 Powershot wont turn on - Canon PowerShot SD400 / IXUS 50 Digital Camera


I read a part solution on your web site about my Canon sd400 failing to start. The message gave a few free words about a micro swith in the cover. I couldnt find it! I called Canon tech and they said there was jo such switch. I packed up the camera ... Canon PowerShot SD400 / IXUS 50 Digital Camera

I have a Canon PowerShot A400 digital camera. when I turn the camera on, it acts like it is going to turn on, then it starts beeping and the screen goes black. It has the message E18 in the lower left corner of the screen. I changed the batteries, but it is still doing it.


Please see this post:\015\012\015\012http://www.fixya.com/support/t102982-e_18_problem\015\012\015\012Good Luck!\015\012\015\012Brian ... Canon Digital Cameras

My canon SD850 IS digital camera is not even a year old and well taken care of. I thasnt been dropped and is already broken? What do i do...everytime i turn it on all of the sudden the lense is stuck poped out and it says lense error restart camera? Please help fast i just bought this becasue my last cannon broke and its thanksgiving tomorrow , i need pictures!


Take a look at the suggestions at the top of page 122 of the Advanced Camera User Guide. The suggestion is that the cause may have been that the camera was still on when the memory card/battery cover was opened. Try closing the cover and then turni ... Canon PowerShot SD850 IS Digital Camera

Canon powershot power will not turn on. - Canon PowerShot SD600 Digital Camera


... Canon PowerShot SD600 Digital Camera

Help Hi. I recently added my brother's new Canon PowerShot SD1000 Digital Camera to my laptop. It already had my downloaded ZoomBrowser EX on it. Now, it won't let me load my pictures from my camera for some reason. I click on "Acquire and Camera Settings" and click on "Connect to Camera" the button shuts out. Please feel free to ask me any questions. Thank you very much. my doesn't say i have a virus when i plug in my camera and then turn it on in playback mode, as i've always done, the pictur


It's very hard to troubleshoot software problems online, and it likely is a software issue. But why put up with the headaches of bad software in the first place? Please see the following blog article, as it describes the use of a card reader as a muc ... Canon PowerShot SD1000 Digital Camera

When i press the power button to turn on the camera, the lens does not come out as it should - I get a "Lens Error - will shut down automatically - restart camera" appear on the screen - My Camera is the PowerShot SD1400 IS Digital ELPH - I have only had this camera for a few months


See Lens Error ... Canon PowerShot SD1400 IS IXUS 130 Digital Camera

Hello, I have a digital camera CANON PowerShot SD790 IS IXUS 9015. The lens started to come out as I turned the camera on and nothing was blocking the camera when doing so. But, suddenly it stopped and the lens is stuck and I can't get the camera to work. Please help. Thank you!!! Kristina.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot SD700 IS Digital ELPH / IXUS 800 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.6414 seconds