Having problems with your Canon PowerShot SD500 / IXUS 700 Digital Camera ?

The lens is stuck in the out position, so the camera will not turn off.


Answers :

Fixing a Lens Error on a Digital Camera
\012
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Canon PowerShot SD500 / IXUS 700 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Lens stuck The camera lens is stuck in the out position and the camera won't turn on at all. The camera was working just fine a the day before this happened. I have replaced the batteries and attempted to turn the camera on an off several times.


Lens unit faulty and camera has gone into error mode. Repair lens ( several possibilities here ) and reset camera and it will work fine. ... Fuji FinePix S3100 Digital Camera

Lens stuck My Sony Cybershot lens is stuck in the out position. It occured when I went to take a photo, the camera turned on and then the battery went dead; not enough juice to turn it off. It was frozen like that for about a day and a half, I did not have access to an outlet. Once I charged the battery, it not struggles to move but is stuck. The LCD display says, "turn power of and then back on" Is there a trick to un freezing it? I don't want to send it in for repairs, my warrenty is exp


Hello, I have read other forums that suggest that quite literally rapping or swatting the unit on its bottom half can actually solve the problem and get things going again. I am going to try it with mine. I too have a stuck lens. Here is a link that ... Sony Cybershot S650 Digital Camera

I have a samsung NV-10 digital camera. Recently the lens that pops out when you turn the camera on, is not stuck in the open, expanded position. Now when I turn the camera on, it beeps 4 times then turns off, with the lens expanded. Any idea how this can be fixed?


... Samsung Digital Cameras

My Canon PowerShot SD850 IS has a lens that is stuck in the extended position. I get a screen that says lens error, restart camera, but when I try to connect to the software, I get a screen on the computer telling me the computer cannot detect the camera. Battery is freshly charged, and I get the little yellow bird picture on the camera when I turn it on. It beeps about 4 times, and then turns off. Is there a safe way to get the lens to retract?


Don't play around with that lens, you can do more damage to the camera and focus with some of the stuff people tell you to try. Your camera just needs to be serviced and you'll be working great again. The shop that specializes in service for the powe ... Canon PowerShot SD850 IS Digital Camera

A friend of mine dropped my camera while the lens was extended. The camera now does not turn on but makes noise and attempts to turn on. The lens goes out and then back to the position it is stuck in. I don't know what to do to fix it or where to take it. I have an Casio Exilim EX-S10. It's an expensive camera, so I'm hopeful it can be fixed.


The lens mechanism could be jammed and cause a failure of the lens control system. You can remove battery and card replace battery and while switching on tap the lens hood on your hands so as to disengage any dirt or mechanism being struck. ... Casio Exilim Card EX-S100 Digital Camera

I have a Kodak EasyShare Z1485 IS, the lens barrel is stuck in the furthest extended position. It was left alone and not operated for several months, though I have replaced the battery. The camera turns on for about 3 seconds at a time, I tried to turn it on several times with the lens barrel inching forward each time. It stopped going forward and has become stuck in what appears to be the furthest-extended position.There does not appear to be any particulates obstructing the lens barrel as far


Your camera almost certainly has a lens error ... Kodak EASYSHARE Z1485 IS Digital Camera

I have a fujifilm finepix ax560. when i turn it on, i get a message to turn off the camera and turn it back on again. also the lens is stuck in the open position.


... Fuji Digital Cameras

My camera lense is stuck in the out position. When I turn on the camera it tries to change the lens position and then beeps and turns off. Any sugestions on how to fix it?


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Samsung SL202 Digital Camera

Jammed camera The lens on my Digimax S800 Samsung camera is stuck in the open position and when I put new batteries in it and tried to turn it on it beeped three times then shut off with the lens still in the open position. What's up with that? Will I need to send it in to the manufacturer? [email protected]


A temporary fix to power up is to press the menu and power button at\015\012the same time. When the lens is extended and it beeps, on my camera ,\015\012the lens is *stuck* Give it a gentle tug , then try the power button\015\012again ... Samsung Digimax S800 Digital Camera

My camera lens is stuck. I turned it on, it ran out of battery, it turned off, the lens stayed open, put new batteries in (positively the right way), turned on, blank screen, lens won't shut.


Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Samsung Digimax S500 Digital Camera

Camera fallen with extended lens position. Lens stuck open and while turning on the camera it is giving error Lens error restart camera


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that ... Canon PowerShot SD850 IS Digital Camera

Lens error, restart camera telephoto lens is stuck in zoom position and won't retract, so when i turn on camera, screens says "lens error, restart camera", but it won't restart...just keep coming up with same error message


Hello mnickoliThis is a fairly common error especially with the A560.This either means that something is jamming the lens , or that the\015\012lens sensor is faulty. This is a very , if not the most common problem\015\012with modern digit ... Canon PowerShot A560 Digital Camera

Fujifilm 10.2 mega pixels digital camera w/SR Auto Scene Recongnition 2.7 LCD. The batteries were dying, we put others in and it won't turn on. We plugged it into the DC outlet (still won't turn on). Connected it to the computer, it won't turn on. (you have to turn it on in order for the computer to recognize it, I think) Anyway why won't it turn on? The lens is stuck in the open position and we just wanted to get enought power to it to close the lens. Can you help?


Maybe the problem is the kind of batterys, change another brand an try remember you need a nikkel batterys ... Digital Cameras

Camera wobn't turn on & lens stuck in out position


Apparently the problem with my camera shutting down and the lens staying out, was the rechargeable batteries I was using. They basically lkicked the bucket, and were no longer working., I bought a new set of lithium batteries and the camera is work ... Samsung Digimax A7 Digital Camera

My daughter was using the camera and she said the lens was stuck in the extended position so she pushed the lens back in ... Now when I try to turn it on an error comes up saying 'lens error restart camera


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is t ... Canon PowerShot SX100 IS Digital Camera

As i was turning on the camera, my fingers blocked the lens and it got stuck. i pushed the lens back to its original position when it is off. now when i turn the cam on, the screen is blank and the lens wouldn't open. what should i do?


Try to get sanyo service for this camera.\015\012\015\012http://us.sanyo.com/Customer-Support-Service-Center-Locator ... Sanyo VPC-S880 Digital Camera

My camera displays E18 on the lower left hand corner no other operation I turned the camera on the lens deployed and it intitiated OK but I can hear some activity such as motor etc. but after 10-20 sec it dipslays E18. I can view pictures, set up the camera but the moment I try to activate the caera function it goes into this routine. The lens now is stuck in the deployed position. I removed the batteries (Energizer Lithium), checked them they are good?


... Canon PowerShot S2 IS Digital Camera

Camera dropped. lens is stuck in open position, won't turn on


HelloThank you for using FixYa for your problemZoom lens is jammed, It should be taken to an authorized repair centre for a repair estimate. Very few digital cameras have any user-serviceable parts. Pl ... Digital Cameras

My camera lens is stuck in the out position and wont retract when i turn camera on makes lots of bleeps and turns off


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed ... Pentax Optio M40 Digital Camera

My sister recently gave me her old Kodak easyshare m1033 camera, which is nice because i have a lot of use for it. At a recent concert of a friend of mine's, I was taking pictures and the camera died with the lens stuck in the out-position. I didn't think much of it and decided I'd bring it home and charge it and then retract the lens. However, when I tried to charge it (I charged it for 12 hours straight, multiple times), it turns on for 1-2 seconds displaying that the date and time have been r


Try this: remove the card and battery...press every button...leave it alone for 20 minutes...insert the card and then the battery...turn it on. If that doesn't work, try these:\012\012 ... Kodak EasyShare M1033 - black Digital Camera

My camera is the fe-370 8 mega pixal. The permanent rechargable battery is fine. Camera wont turn on. Zoom lens is stuck on the on position. I think I might have gotten it wet. It just won't turn on now


... Digital Cameras

The lens on my Olympus m760 camera is stuck in its out position. Even When i turn my camera off or take the battery out, the lens stays fully zoomed out and makes a funny noise like its tyring to retract. Please help.


This is probably caused due to a fall or so.. try to technically have a 360 look at the sides of the lens were at one instant u will notice a slight droop.. now u have to carefully push the lens in carefully with **** like motion for which a click no ... Olympus Digital Cameras

Is there a way to "restart" my Casio Exilim EX-Z700? While I was taking a picture it seemed to freeze while it was trying to display the picture I just took - then, with the lens still popped out the screen stayed blank and it turned off, and now it won't turn on. The lens is still stuck in the "out" position. No buttons work. I tried to put it in the cradle to charge, and tried a different battery as well. Nothing works. Camera is dead!


Normally changing the battery solves this.Make sure you replace it with a good quality new battery and make sure it goes in the right way around as when you get in a flap it often ends up in the wrong way! ... Casio Exilim Zoom EX-Z700 Digital Camera

Lens Stuck Sony Cybershot DSC--P73 My wife dropped this camera and now the lens is stuck. When I turn on, the screen just stays black with the word Access and then instructs me to turn off camera, and turn back on. I am able to pull the lens out manualy, but it just stays stuck there also. Please help. this has been a great camera. Thanks


Same problem guys!!! LENS HAD GOT STUCK - ABOUT ONE THIRD OUT after a knock. After lots of playing, and tapping and batteries in and out tried the whole twisting and pulling thing whilst turning off and on.\015\012\015\012After a few minu ... Sony Cyber-shot DSC-W50 Digital Camera

Camera will not turn on changed batteries several times. Turns on then won't turn off /turns off and won't turn on - lens gets stuck in the extended position.


Best bet send it back!! ... Olympus Camedia C-700 Ultra Zoom Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3432 seconds