Having problems with your Canon PowerShot SD600 Digital Camera ?

The lens on my sd600 won't open when I turn the camera to picture taking position. Screen goes black and message says ''lens error, restart camera''. I have to go back to view mode and then turn camera off and on again in order for partially opened lens to retract fully and close.


Answers :

Fixing a Lens Error on a Digital Camera
\015\012
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Canon PowerShot SD600 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The lens on my sd600 won't open when I turn the camera to picture taking position. Screen goes black and message says ''lens error, restart camera''. I have to go back to view mode and then turn camera off and on again in order for partially opened lens to retract fully and close.


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Canon PowerShot SD600 Digital Camera

A85 Dead During a normal session, switching from picture-taking mode to view mode, the lens would not retract and the picture in the view froze with the current image. I could not turn off the camera. After a while, the batteries got very hot, so I removed them. I took out the CF card. Later, I replaced the batteries and the put the card back in. The camera worked very briefly, but the LCD view would not work, displaying flashing lines on a black background. New batteries didn't help. The camera


I read something about the fuse going out...http://www.dcresource.com/forums/archive/index.php/t-18151.html ... Canon PowerShot A85 Digital Camera

When camera gets turned on, the lens goes in and out of focus a few times and then screen turns blue and displays "D : 5f08 5e02" and does not go back to shooting pictures again. But for just looking at the pictures on the memory card, it works if turned on in that mode. If turned on in photo-shooting modes, it cannot be switched back to view photos. (OLYMPUS M700)


It's a sensor issue. The error indicates there is a problem on the lens.It may be caused by sand, broken gears or any other foreign object in the lens mechanism.A simple fix is to turn ON camera while holding it with\015\012the len ... Digital Cameras

When turned on, lens goes out then right back in, eventually camera shuts off. view mode OK.


This might be an E18 lens error issue. Here's some things that you can do to try to correct it. Have already fixed several cameras with this problem by using these methods:\015\012http://www.e18error.com/repair.html ... Canon PowerShot A75 Digital Camera

Our Olympus 7010 has gotten the lens stuck out, and now when we turn it on in any mode other than viewing pictures, the orange on light comes on, the view screen displays Olympus and the orange light on the back side of the camera just above the upper right corner of the view screen blinks about 7 times and then the camera shuts off.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Olympus Stylus 7010 Digital Camera

Lumix tz3 Please turn camera off and then on again" as soon as camera is switched on. I Can view any menu, or read SD card, but cannot take any pictures. If I turn on in a picture taking mode it starts to focus and then the message appears, when I turn it off the lens does not close. If I turn on in playback mode, it works fine, if I turn it off from playback mode, then the lens closes. Basically, any picture taking mode triggers the error message. Solution?


Low battery maybe? Try holding camera firmly in one hand, with camera on and in record mode, and strike in on its edge firmly on the heal of your other hand. This technique is often sucessful with temporary camer 'quirks' like freezing, lens not full ... Panasonic Lumix DMC-TZ3 Digital Camera

Sony Cybershot DSC W90, when I turn the camera on I get a message that says to turn off and back on again. It will allow me to view photos already taken but will not turn on to take pictures. I hear the lens trying to go out into picture taking mode, but it does not open.


There are a number of solutions you can try,1.\015\012\015\012you will need to turn off the camera and hold the camera on the edges in a way that you wouild hold a pack of cards\015\012you ... Sony Digital Cameras

Kodak Z700 Camer appears to be in a locked out mode. The lens is stuck partway out and does not retract if the camera is turned off. When turned back on The Green light comes on for approximately 5 seconds and then goes off. The viewing screen comes on for 2 to 3 seconds and goes out as well.


Hi,Tentative solution:I had the identical problem. I went as far as disassembling the camera ... not recommended.Instead of fussing with the lens cover, I pressed on the lens assembly (gently), the lens retracted and the ... Kodak EasyShare Z700 Digital Camera

Camera was on, working fine. When powering off, telescoping lens did not retract so lens remained extended just a bit with lens cover open. Waited a few minutes, turned it back on and I get the "access" display message then the beeps and (turn power off and back on) message. While off, I have removed the battery, replacing it with a fully charged spare and it still does this. The lens tries to telescope a little bit and retracts a touch, but I can't get the camera out of this mode. Can it be res


Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Sony Cyber-shot DSC-W55 Digital Camera

Optio M20 Camera: Press on/off button to power up camera, the camera opens the lens cover, turns on a red led inside the lens, cycles the lens out and back in,then makes about 5 little popping noises. The back screen shows Pentax Optio screen for a second, then then the screen displays the word Auto Picture in the center of the screen and Green Mode at the bottom and at the same time it cycles the lens out and in. And for a brief moment in the back ground of the screen you can see the picture st


I got it!!! on my cam i hold down the menu button at the same time power on, it will showup a " ver 1.00" and lens move a little maybe u have to do it 2 times but second time it should work ... Pentax Optio M20 Digital Camera

Ok so i am turning on my camera (an Fe-340) and the lens go in two or three times then when the screen finally does come on it is blurry and way out of focus, also when i attempt to adjust the zoom the camera turns itself off, if i attempt to turn the camera off using the power button it goes off but the lens does not retract.All other functions on the camera are operating correctly to my knowledge i can even take a blurry out of focus picture, view it in display mode or even transfer it to my c


It may be something more serious, but the problem you describe is\015\012frequently due to corrosion on the battery contacts inside the camera. \015\012Remove the batteries and wipe the camera contacts firmly with a clean\015\012cloth (heavy corrosio ... Olympus FE-340 Digital Camera

I have a Canon Powershot S3 IS and I was looking at picture I had taken and the lens was retracted. I switched to the camera mode and the lens started to come out and hit my leg and stopped half way. The lens went dark. I turned it off to retract the lens and then turned it back on. The lens came all the way out but the screen is still black and I could feel the camera and just barely hear it making the noise it makes when the lens is coming out but it was already all the way out. I switche


Format ur memory card ....and replace the cells.....might work...contact the customer care for help ..they mightr be able to fix it ... ... Digital Cameras

Lens Error When I turn on the camera in any mode except play back, the lens will come out as if it's coming on but then the lens' go back in and the camera shuts down. The batteries are fully charged and the camera has not been damaged in any way.


I am sorry to say but you have a physical issue with the camera. Your either going to have to take the camera apart yourself or bring it in for service. Try working with their support \015\012\011\011\011\011\011\015\012\011\011\0 ... General Electric A835 Digital Camera

Hi welcomejee, I read all your solutions regarding the digital camera Sony DSC N2. I really have to thank you for your precious Some of the problems are very similar to mine: After the camera fell on the ground from about 2 meters in off mode the lens would come out and immediately back in 4 times in a row. After that the lens is back in, a beeping sound comes up and on the display it is written to "Turn the power off and on again". Of course that does not help at all. The lens is opening


George, this is most likely a lens issue, and more precisely, probably a stripped gear when it fell. You will have to disassemble the entire unit to get at the lens assembly, and will probably be a professional by the time you get through! ... Digital Cameras

I have an Olympus Camedia C-50 Zoom camera that has worked fine for a few years, but suddenly when I open the lens cover, the camera does not turn on. I charged the battery and it is fine, and I can use the quick view button in the back to see what I have already taken, but the lens will not come out and turn the camera on. What can I do?


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Olympus Camedia C-50 Zoom Digital Camera

My ex Z1000 wont take pictures. i turn the camera on the lens goes in and out some times it looks like its going to let me take a picture and then the lens closes back into the camera and the screen goes black. It looks like the cameras off but I push the play button on top and it lets me view pictures. I don't think its the lens because the lens seems to open and close fine. Ive only used this camera 3 times and it has been stored safely so Im not sure what happened. It will only let me get int


Your camera problem has the problem chance. Fisrt you should try with full charge battery. sometime weak battery cause also. Second main pcb does not resetting every time after taking picture.\012I hope you luck! \012Would you give more detail pr ... Digital Cameras

Hi, I own a Sony Cybershot camera, and it has been giving a few problems as of this week. The lens keep re-adjusting in and out when I turn the camera on to take pictures. It however responds just fine when in picture-view mode. There is a screen prompt that says 'Access' when the camera is turned on, as well as the message 'turn off camera and start again'. I do not think that the camera had fallen at any time, and it is just under a year old. Thanks a lot for your response, Sarah.


... Digital Cameras

When I turn the camera on, the canon logo appears on the display and the red light in back above the menu button keeps blinking, but nothing happens. When I turn it on in the "taking pictures" mode or "view pictures" mode, it just hangs and acts like it has trouble reading the CF card. I've tried multiple cards and had the same problem, so I think it's the camera and not the cards. Any ideas?


Canon logo is starting of camara indications just as company manuals ... Canon PowerShot S1 IS Digital Camera

Lense problem When i turn the camera on in picture taking mode the lense does not come out all the way and if i push it again it still does not come out and then when i push the power button a third time it closes the little bit it opened... but not all the way. However if the camera is in play mode and i turn it on, the lense comes out all the way just fine... then goes back in on its own and i can view the pictures. Because of this it appears the mechanism is working fine but there is maybe


Dear jmgrev,\015\012\015\012Whenever you turn your camera on and your lens doesn't go in and out properly you are likely experiencing a lens error of some sort. Look for an error 18 or a "lens error restart camera" message. If either of t ... Canon PowerShot SD630 Digital ELPH / IXUS 65 Digital Camera

Samsung pl50 camera: It is fully charged and turns on and i can view pictures but i can not take photos the lens comes out and goes back in whilst it beeps. Sometimes the lens is stuck but after a wig


... Samsung L200 Digital Camera

When camera turns on, it makes a buzzing noise as lens moves out and then moves back in again, and then camera turns off turns off--no functions available during this period. cannot view or take pictures, new card and battery is fully charged. can this be fixed? others have had same problem but no answer for it on this page: http://www.fixya.com/support/t228714-turns_lens_comes_out_turns_off


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Pentax Optio T10 Digital Camera

My Sanyo VPC-E870 lens will not go back in. The camera will not turn on, except when I am in the playback mode. Periodically I will get an message that say lens error 21 and sometimes lens error 15. I have only had the camera since Christmas. Thank you for you consideration. Robert Castro


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Digital Cameras

My Cannon Power Shot A520 Camera will not power the lens up when I turn it on. I get the message "No Image" on the viewing screen, but nothing else happens. Back Switch is set on camera symbol, but camera acts like it is set on view. I have installed new batteries and battery terminals are clean.


The camera may need a software update which can be done through manufacture for $50 or you can downlaod an update from their website and follow the directionsOr the zoom may be dirty or debris is stuck in the zoom lens and needs to be blow out ... Digital Cameras

Lens Problem Hiya,hopefully someone out there can help....when turning the camera on (in camera mode) the lens extends, then retracts itself and the camera shuts down automatically. I can use and view all other features via "favourites", but just can't take another photo. Any tips would be much appreciatted.


Update the v550 firmware via Kodak's website. Follow the instruction... hope this helps RICK ... Kodak EasyShare V550 Digital Camera

Camera Everytime I turn my camera on it comes on, but the lens goes in and out a few times before the screen goes completaly black and says to turn the camera off then back on again, I do, and the same thing happens all over again, not allowing me to take any pictures. However, I can still view the pictures that have been taken...and that are on my memory card.


It a lens misalignment try tapping the lens gently in an opposite direction the camera dropped on and that should pop the gear back into place ... Sony Cyber-shot DSC-W70 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5533 seconds