Having problems with your Canon PowerShot SD800 IS / IXUS 850 IS Digital Camera ?

The lens will not fully retract - Canon PowerShot SD800 IS / IXUS 850 IS Digital Camera


Answers :

Fixing a Lens Error on a Digital Camera
\015\012
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Canon PowerShot SD800 IS / IXUS 850 IS Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The lens will not fully retract - Canon PowerShot SD800 IS / IXUS 850 IS Digital Camera


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Canon PowerShot SD800 IS / IXUS 850 IS Digital Camera

Hello I have a Canon digital elph sd600 and the lens won't retract all the way and it gives me a lens error message to restart the camera but the lens is stuck halfway - it won't extend fully and it won't completely retract. Any suggestions as to what I need to do to fix this? Thanks so much I appreciate it.


See http://www.fixya.com/support/r13011856-lens_error ... Canon PowerShot SD600 Digital Camera

Canon powershot SD700 IS len retract problem - Canon PowerShot SD700 IS Digital ELPH / IXUS 800 Digital Camera


... Canon PowerShot SD700 IS Digital ELPH / IXUS 800 Digital Camera

I have a Digital IXUS 700 Canon camera and the lens will not retract. It makes the sound to retract but won't retract.


Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Digital Cameras

Lens wont retract - Canon PowerShot SD630 Digital ELPH / IXUS 65 Digital Camera


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Canon PowerShot SD630 Digital ELPH / IXUS 65 Digital Camera

Lens does not retract. Camera frozen - Canon PowerShot SD400 / IXUS 50 Digital Camera


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot SD400 / IXUS 50 Digital Camera

I am having problems with my Canon PowerShot SD1300 IS IXUS 105 Digital Camera. when i am in the playback mode, looking through pictures, the screen will cut off at the last picture (when instead, it should just go straight to the first picture). the lens does not retract and if i press the on/off button, the camera turns back on, but then cuts off again whenever i'm trying to look through pics. I can't figure out if I need to send it back and exchange it or what. Please help me, thank you!


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that ... Canon PowerShot SD1300 IS IXUS 105 Digital Camera

Lens wont retract so camera turns itself off - Canon PowerShot SD750 / IXUS 75 Digital Camera


If the lens will not retract, and you cannot get to the menus, you need to have it repaired or sell it for parts on a site such as Ebay.Since it is not working anyway, you may want to try the following, be warned that it can cause more damage, ... Canon PowerShot SD750 / IXUS 75 Digital Camera

My Pentax Optio S10 digital camera is giving me problems. Initially the lens would not extend fully and would then immediately retract and the camera would then turn itself off. After cleaning the extended lens barrel each time it extended, I found it would open further each time. It nows extends fully, but still retracts immediately thereafter. At the time the screen shows the green Optio screen for a split second and then shows an out of focus shot of whatever the camera is pointing at, bef


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Pentax Optio S10 Digital Camera

Lens will not retract - Canon PowerShot SD890 IS / IXUS 970 IS Digital Camera


... Canon PowerShot SD890 IS / IXUS 970 IS Digital Camera

E18 error message lens will not retract - Canon PowerShot SD500 / IXUS 700 Digital Camera


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Canon PowerShot SD500 / IXUS 700 Digital Camera

My Canon IXUS Z70 APS camera has just gone "dead";I have put in several new batteries and it will go in to starter mode once but then goes dead again with fully retracted lens. Is there anything I can try? Sue at [email protected]


... Canon Digital Cameras

Hi there, I have a Canon IXUS 90 IS - the lens is extended out and won't retract when pressing the 'on' button. The camera only makes a 'turning sound ' from the motor ( I asume the motor), but the actual display in the back reads' Lens error, restart camera' The nearest camera specialist for Canon are a good 600 and 1400 km's away respectively ( I live in Durban, South Africa)so would like to rather try fix this myself before paying, most likely a similar amount to buy a new camera. Any suggest


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Canon PowerShot SD790 IS/ IXUS 90 IS Digital Camera

Lens error my canon IXUS 860 IS is having a lens error problem. firstly, the lens cant retract back and when i try to switch it on, the screen will say 'lens error, restart camera' so how do i restart the camera?? i'm currently overseas and although my camera is within warranty, i cant possibly send my camera back to the original country for repair. is there any DIY method?? i'm an amateur at cameras so i do not wish to try any method that may further make the problem worse. thank you for your h


This is probably THE single most common failure among digital cameras. There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Canon IXUS V2 Digital Camera

My canon camera Ixus 8515 has an error when turning on (after some 'stuck' noises) that reads 'lens error, restart camera'. The lens is not retracting. The camera has not been dropped. Was working fine one minute, then camera appeared out of focus the next. When I turned camera off then on again, error appeared. Lens won't go back in. Have not tried forcing it as yet.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you wi ... Canon Digital SD900 / IXUS 900 Ti Digital Camera

I am having power supply and lens problem with a canon sd1000 digital camera. its not working with the battery inside and the lens got stuck and was not closing and now it is open but the camera is off and the lens is also extended the battery is fully charged and functional but still is not powering the camera back on. i currtently took the outer casing off and attempting to navigate through the boards looking for a solution to the power supply and then the lens error of bein stuck problems.


This is a mechanical fault and would only be repaired through servicing. You should be able to get it repaired under warranty or a camera centre. If the costs are too high it may just be worth replacing the camera. ... Digital Cameras

I am having power supply and lens problem with a canon sd1000 digital camera. its not working with the battery inside and the lens got stuck and was not closing and now it is open but the camera is off and the lens is also extended the battery is fully charged and functional but still is not powering the camera back on. i currtently took the outer casing off and attempting to navigate through the boards looking for a solution to the power supply and then the lens error of bein stuck problems.


I am afraid you have the notorious lens stuck problem. If you google "canon lens stuck" or "canon lens not retracing" the results will be in millions. Canon's quote for repairing this issue is well over the cost of the camera itself. However all is n ... Canon PowerShot SD1000 Digital Camera

I am having power supply and lens problem with a canon sd1000 digital camera. its not working with the battery inside and the lens got stuck and was not closing and now it is open but the camera is off and the lens is also extended the battery is fully charged and functional but still is not powering the camera back on. i currtently took the outer casing off and attempting to navigate through the boards looking for a solution to the power supply and then the lens error of bein stuck problems.


This is a mechanical fault and would only be repaired through servicing. You should be able to get it repaired under warranty or a camera centre. If the costs are too high it may just be worth replacing the camera. ... Canon PowerShot SD1000 Digital Camera

Lens error restart camera on Ixus 870IS - Canon PowerShot SD880 IS / Digital IXUS 870 IS Digital Camera


Fixing a Lens Error on a Digital Camera This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart ... Canon PowerShot SD880 IS / Digital IXUS 870 IS Digital Camera

When I power on my Olympus Fe-340 digital camera, the lens extends and retracts fully 4 times. The red light located next to the power button flashes while the process occurs. After the 4th retraction of the lens, the camera powers off.


This could be the battery issue. I have an FE-370 and got almost the same problem. The Red light flashes and the camera shuts off. I went to Olympus store and they try a known working battery (LI-60B) and the camera is now working correct ... Olympus FE-340 Digital Camera

Digital Camera Have a canon powershot SD700 IS digital elph ... "lens error ... restart camera" shows in the display and lens will not retract ... any suggestions?


The following blog outlines some repair options for a lens error:\015\012http://camerarepair.blogspot.com/2007/12/fixing ... Digital Cameras

I have a canon ixus 900Ti. I turned it on yesterday and the lens came out as normal. when i went to take a pic the camera shut off but the lense never retracted. when i turned the camera back on the splash screen came on, followed by a series of beeps and then and error message saying "lens error, restart camera". restarting has not solved the problem. its like the lens is stuck out. hope you can help Regards Liam


Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Digital Cameras

Lens problem Hi. I have an Olympus FE-190 digital camera. not sure what happened, but now there is a problem with the lens. when i turn on the camera, the lens extends, retracts, several times (trying to find "home" I think). Image on the display screen is blurry. it WILL take a very blurry picture. there is a faint 'ratcheting" sound when the lens is fully extended. is there a way to 're-set" or calibrate the lens extension setting or focus? thanks very much for your assistance.


Take it to Best Buy for repair. ... Olympus FE-190 Digital Camera

Hello, I have a digital camera CANON PowerShot SD790 IS IXUS 9015. The lens started to come out as I turned the camera on and nothing was blocking the camera when doing so. But, suddenly it stopped and the lens is stuck and I can't get the camera to work. Please help. Thank you!!! Kristina.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot SD700 IS Digital ELPH / IXUS 800 Digital Camera

Canon Digital Ixus i7 zoom, Camera lens is half open, when camera is swithced on theres a buzzing sound and then the camera says "Lens Error, Restart Camera". What can i do to fix it?


At the presemt moment i also have this problem...now trying to take my camera apart, put the lense back proberly and then put it all beack togeter/... ... Canon Digital Cameras
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5802 seconds