Having problems with your Canon PowerShot SX100 IS Digital Camera ?

I have a Canon Power Shot SX120 IS camera. I turned it on and the lens open a portion of the way and I got an error message that say, "Lens Error Restart Camera". I put fresh batteries in it this morning and have only taken about 10 pic's. I turned the camera off and removed the batteries then replaced with new ones but I still get same message. Please advise if you can.


Answers :

Fixing a Lens Error on a Digital Camera
\012
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
My canon did the same thing and the person told me it would cost 139.00 to fix it I wasted 200.00 already on the camera and its almost 5 years old . I am temped to throw it away it will cost more then my Fujifilm camera. It's not a better camera then my Fujifilm. I regret buying the canon I hope my Fuji film never gives me that error I have it in a case but I have plastic where I look at it and the other side has a lens cap . I keep it on at all times when not in use. Protect it
Repair Help & Product Troubleshooting for Canon PowerShot SX100 IS Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Canon Power Shot SX120 IS camera. I turned it on and the lens open a portion of the way and I got an error message that say, "Lens Error Restart Camera". I put fresh batteries in it this morning and have only taken about 10 pic's. I turned the camera off and removed the batteries then replaced with new ones but I still get same message. Please advise if you can.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot SX100 IS Digital Camera

Error message my nikon D -80 is flahing an error message. When i try to take a photograph i hear it cycle, but nothing is taken. The automatic focus does not work. I think i might have turned the camera off by accident while it was writing a photo to my card *sighs* I have tried removing the battery, a new card, remove and replace the lens, remove lens and clean contact, and talking very sweetly to the camrea. Nothing worked and the same messages is displayed when i turn the camera on. Any advic


This may be due to the aperture ring in your lens. Try the following:\015\012\015\0121. Turn off your camera\015\0122. Move the aperture ring clockwise then lock\015\0123. Turn on your camera and try again.\015\012 ... Nikon D80 Digital Camera with 18-135mm Lens

I bought new batteries from local store (one from Walmart and one from Meijer) but both would not work in my Cybershot DSC-H55. On powering up, I get the message "For use with compatible battery only" then it shuts down. The battery that came with my camera still works fine. I thought I had bought bad batteries but I returned for exchange, and 2 replacement batteries from 2 different stores still shows the same error message. Either the stores are selling 3+ year old batteries that have gone b


... Sony DSC-H55 Digital Camera

Frame error Turn on and take photo and then a message comes up saying "frame error" and then Even shutting the camera off. When turning it back on it still says "frame error" . When you take several photos you only end up with a very few on the memory card. What is the problem and how can i fix it? I cant view any of the photos. I replace camera with a new battery. Could it be my SMART CARD. Need help! Fuji MX-2900


... Fuji MX-2900 Zoom Digital Camera

No matter what I do, my camera keeps giving me a "Battery Depleted" message whenever I try to turn it on. It's a Pentax Optio E40, and I've only had it a couple of weeks. It was working fine, but then one day when I tried to turn it on, I got this error. I replaced the batteries, but the error still came. I've checked the orientation of the batteries, tried re-inserting them, etc, but nothing seems to work. Please help! Thank you!


I had the same problem and checked the manual. If you haven't used the camera in a while and there were either no batteries or dead batteries in it, put in new batteries, keep it off, and WAIT a few minutes. Then try to turn it on. This helped with P ... Pentax Digital Cameras

With our panasonic DMC-LZ5, first we got a message saying replace batteries, which we did (with new ones). Now, the screen is all white with a message saying please turn camera off and then on again. We've tried several sets of batteries, and turned it off and on again. The picture of the battery is all in white, with a line through the middle. Any ideas on how to reset?


Http://www.fixya.com/support/t1100571-lumix_dmc_lz5_replace_battery ... Panasonic Digital Cameras

I have a new (Dec., 2009) D90. This morning I discovered that I had an "Err" message and a "CHA" message. Both were on the LCD panel on the top of the camera. I was not able to turn the camera off, and the only way to turn it off was to take out the battery. Upon reinserting the battery, everything appeared normal, but after taking one shot the problem reappeared. The interesting thing was that I took the camera body to a Nikon certified shop in New York, and they tried it with a different lens,


The Nikon user manual says on Page 256 that the ERR message indicates a camera malfunction and to clear it, you must release the shutter. \012\012 I have found on my D-90 that I can usually release the shutter by turning the camera off and ba ... Nikon D90 Digital Camera with 18-105mm lens

I have had this camera for a couple of years and I love it. However, recently, I was taking pictures and my battery went dead (I thought). So I bought new batteries and replaced the old ones. The camera will power on, but turn itself off immediately afterwards. Or it will power off after a few seconds. I tried replacing the batteries again, but no luck! Can someone help me figure this out? however I can veiw existing photogrhaps in camera but the very movement i try to take new photo camera got


Actually u are a victim of BAD CCD see this link belowhttp://www.imaging-resource.com/badccds.htmlbut good news is all brands are doing this free of charge repairs sony, fuji, canon , olympus all, some models have service adv ... Sony Cyber-Shot DSC-S40 Digital Camera

Lens will not retract - getting error message says: Lens error. Camera will not turn off or take a picture. Battery worn out but new ones put in and still can't get it to retract.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that ... Nikon COOLPIX L18 Digital Camera

Turning on. my camera won't turn on no matter what I do, for a few days it said low battery and i won't lie i kept turning it on, but one day it turned off but the lens never went back inside and the camera won't turn on. I replaced the old batteries with new ones, but it didn't work. I press the button, but the light only flashes for a second before blinking out.


Here are some simple things to try first for a camera that won't power on. They won't work for every case, but they're worth a try. Think that the first listed fix may work for your camera:\015\012\015\012 ... Canon PowerShot A520 Digital Camera

Zoom Error Just bought an Olympus SP550 Ultra Zoom for my daughter. In less than 24 hours the cam developed a problem. When she turns it on, the zoom lens goes part way out, a message "zoom error" shows on the screen, and it powers itself off. We thought it might just be the batteries, but new ones didn't help. Similar problem with SP-560UZ On power up lens clicks & sticks when zooms out. Then get "zoom error" & powers off. Tried new batteries, helping lens out. Leaving batteries out. Could not


I think a grain of sand was blocking the zoom tubes. This will not work if the camera has been dropped & the zoom apparatus is bent. It is entirely at your own risk & may invalidate any guarantee but they may charge anyway if you have got san ... Digital Cameras

Kodak v610 camera (easy share) My 10 year son was using our v610 camera and the following error message E45 (please see user manual) appeared on the screen. We were unable to switch the camera off and therefore the shutter remained open. The shutter will only close if I remove and replace the battery and when I turn the camera back on the shutter remains open and the same error message returns. I have checked the manual and it doesn't mention this problem. thank you jane


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is t ... Kodak EasyShare V610 Digital Camera

Lense Error I have a problem with a message appearing on my camera screen, "Lens error, restart camera". I have restarted the camera many X's. I have replaced the batteries. That is not the problem. What is the problem? I really do like this camera and it is farely new. Downloaded the Advance Guide and that is how I found out what the message means, but what can I do? Why did is happen? I am putting these questions out there for the experts. HELP


Dear Can On:\015\012\015\012Unfortunately only a small percentage of lens errors can be resolved on their own, such as by restarting your camera. If that doesn't work then the camera will have to be sent into the service center for repair ... Canon PowerShot A570 IS Digital Camera

Canon A400 Hi, I have the above camera (canon power shot A400) and have just solved the E18 error by tapping the plastic A/V out cover - THANK YOU ! However, now, although the camera turns on, lense extends and I get full working order - after a few minutes I get the message 'Change batteriers'. and the camera dies. I have now put in several new batteries (including the little(cr1220) but the same message keeps coming up and the screen and the whole thing dies after a few seconds. Is this a furt


Having using standard LR6 batteries in a Canon before you will only get 3 or 4 pics max before it drains the batteries. You really need high power AA's like 2300mAH+ rechargeables for any good performance or Lithium AA's ... Canon PowerShot A400 Digital Camera

My Finepix s5700 will not turn on even with new batteries. The last thing I did was delete some photos from the memory card. The next time I went to turn it on I thought the batteries were dead and so I replaced them with new ones, but it still will not turn on. And the camera was not dropped.


A possible cause could be the "cut off" switch for the xd picture card door. Check the plastic tabs on the door for damage. If it looks ok then open and close it a few times to see if the micro switch on the board is stuck. This is a cut off switch t ... Fuji FinePix S700 Digital Camera

Hi, I am having S2 IS camera.... Haven't used it for the past 6 months....now facing one problem. I brought new rechargable batteries, charged them properly for about 9 hours and then tried to turn the camera on. Although the Camera turned on, only a blank screen came and nothing was visible. After just 10 seconds, it started showing the message "Change the batteries". Please help me in understanding the problem


First, are the batteries inserted correctly? Try cleaning the battery contacts in the camera with a cotton swab lightly dampened with rubbing alcohol. ... Canon PowerShot S2 IS Digital Camera

My canon digital rebel (ds6041) wont turn on. I have already replaced the battery 4 times with new ones. All fully loaded. still doesn't turn on. I have taken out the mini battery inside the camera, on the internet it said that the camera then would reset itself, still doesn't turn on. Who has an idea, because I don't want to sent it to a reparation store.


... Canon Rebel XT / EOS 350D Digital Camera

My camera gives me a battery exhausted message every time I replace the battery with a new one take one picture and the battery exhausted message comes out. How can I resolve this. I have a Nikon coolpix L 15


Hi,\015\012\015\012Are you using high capacity batteries? ... Nikon Digital Cameras

Battery Problem My 18-month-old Canon A70 is giving "change the battery pack" message and turning off constantly, even though I have fully charged three different sets of new rechargeable batteries and rotate them as soon as the message comes on. Sometimes with this message I pull out one charged set and put the same back in, and it works fine for quite awhile, then repeats later. I imagine this is a problem in the camera battery power circuit or something. Never happens when plugged into the co


I figured out the problem. My AA battery recharger was not making good contact, so although it said the batteries were recharged, this was not the case. After fixing this and getting full recharges, the problem went away. ... Canon PowerShot A70 Digital Camera

Communication error I was in process of downloading pics from my camera to the computer and had to put in a different memory disk into the computer. I have downloaded pics from this dis disk before but now all I get ia a message that says "Communication error" on the camera screen. the battery has a full charge, i have tried taking it out and putting it back in, removed the battery and put it back in. I even tried a brand new cable!! Any one can help!!! thanks kim


Try NOT connecting your camera to your computer.The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or conne ... Canon PowerShot SD1100 IS Digital Camera

My camera is a new purple polaroid 1834, I got it for Christmas. I tried to take a picture the other day and it took one, and then shut down with the lens still out. It will not turn on, and everytime I press the power button a green light flashes and it beeps three times, but nothing else happens. I have tried replacing the batteries with brand new ones..still nothing. I've tried to batteries and everything.What is going on and what can I do to fix it? Is it fixable?


It is fixable but best thing to do is take it back to where you got it for a replacement. Or send it in to Polaroid the lens gears are stuck and the zoom motor sounds like it has gone out. If you have no sucess doing that then let me kno ... Digital Cameras

Hi, I have the Sony Cyber Shot DSC-W130 digital camera - whilst away on holiday a message appears when I turn on the camera "turn power off and on again". I have done so many times but it still comes up with the same message - hence not allowing me to take any pictures. I can view existing images through the window and I can download them fine - I just can't take any new ones. There is plenty of space on the card and a full battery. Any suggestions?


Hi. Yes. turn it on and go to the menu. find reset and reset the camera. this will return it to factory settings.\012\012if you can't get into the menu or if the steps above do not solve the problem do what is called a hard reset. Re ... Sony Cyber-shot DSC-W100 Digital Camera

We just received our brand new canon t3i in the mail. We formatted the card (a 2GB 700X Professional High Speed Error Free (SD) Memory Card Class 10) and immediately started shooting to test out the camera. Everything seemed to work fine until we tried to apply a filter to one of the photos. The entire camera froze. We even tried turning the camera off and it would not shut off. We ended up having to take the battery out and put it back in. When we did and turned the camera back on we received a


Sounds like there was an error while the camera was writing information to the card. You can try reformatting the card using a computer and a card reader, then replace it in the camera and format it from the menu. If that doesn't work and the camera ... Canon EOS 600D Rebel T3i Digital Camera

Picture error I have a problem with my Olympus SP 500UZ. When I take a couple of pictures on one day. Shut the camera down and start it later on to take new pictures. The screen turns blue when I want to see the pictures. It gives the message: Picture Error or Fatal error and every photo on the memory card is gone! I send it to the Olympus repair for three times now, but they tell me every time that there's nothing wrong with the camera. Is this a known problem??


... Digital Cameras

My new C182 camera downloaded our first set of photos okay, now I cannot get it to download our second set of photos ( taken a week later). I plug in the port to computer and camera, then turn on camera, nothing happens. Replaced the batteries with new ones.


If, after the first time you downloaded, you didn't use the "safely remove hardware"' function before disconnecting the camera, you may have corrupted the connection. You can always use a card reader for downloading. They work better anyway. ... Kodak Digital Cameras
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5025 seconds