Having problems with your Casio Exilim EX-S600 Digital Camera ?

I have problem with my casio exilim,lens problem.the lens dont come out and the message say:lens problem ,there is also a noise

Answers :

Fixing a Lens Error on a Digital Camera


This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Repair Help & Product Troubleshooting for Casio Exilim EX-S600 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have problem with my casio exilim,lens problem.the lens dont come out and the message say:lens problem ,there is also a noise

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Casio Exilim EX-S600 Digital Camera

CLICKING NOISE hi, im new to photography so i dont really know much i have the casio ex-z1050 after ive taken a shot, i hear this clicking noise as the viewing monitor returns back ready for the next shot to be taken i also hear the same clicking noise when i move the camera pointing from a dark area of the room to pointing straight out of the window as its adjusting to the light should that clicking noise be there whoever has this camera, please reply if you have the same noise

The clicking noise is the internal focus lens. The S500 and S600 are very succeptible to debris getting in the lens. Or, the focus lens was knocked out of alignment. ... Casio EXILIM ZOOM EX-Z600 Digital Camera

Hello, I have a Casio ex277 digital camera. Also have a new battery for it. The problem is that it won't focus clearly and makes a slight noise in the lense shudder when a picture is taken. The photo is not clear in the display also. I have set the camera back to default to no avail. Any suggestions would be greatly appreciated. Thank you, Greg E.

Hi,\015\012It will be white balance ,set the white balance to auto and when you take a snap try pressing the shutter button half way to let it focus before you shoot. You also make sure the camera is in auto mode . If y ... Digital Cameras

Hi, i gave the same problem of the cam' asking me (on the blue screen) to either turn the cam' off or format the card, (which will erase al the pic's and i dont want it to happen) on the other hand, i cant use that card on my PC bcs it gives me a message of : "the disk drive F is not formatted, do you want to format now?" and i know its not the PC or the CAM' bcs i tried to insert a differant card into the cam' and it worked with no problems both on the cammera's screen and on the PC, i also ha

... Olympus i:robe IR-500 Digital Camera

My wife has the Casio EX-Z1200 and the camera when turning on is showing the message lens error 2, we also now have the problem of the flash not charging despite being on autoflash or flash on. Any ideas as to what Lens error 2 signifys and also why the flash isn't responding. It appears to be charging but doesn't go off. Thanks in advance

HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you wi ... Casio Exilim EX-Z1200 Digital Camera

The Lens will not retract, everytime i press the on off button it simply flashes green for a second and makes a very faint noise. It does load up pictures to my computer though! But it also siad error message see computer, but it only said that there was a connection problem, on the computer?! HELP!!

... Kodak EASYSHARE M340 Digital Camera

Sony dsc-t100 Tried to update to firmware version 2. Camera tries to "Updating Dont turn off". Eventually goes to "Error 10". I can't press anything except round Select button which restarts the updating process again and eventually error message again. I can't find the original firmware anywhere on the web. Only version 2. I believe finding a firmware other than version 2 may solve this problem. Also tried resetting camera. It always goes to same process described above, once the battery is put

Please open the page by clicking the link provided below.http://esupport.sony.com/US/perl/swu-download.pl?m ... Sony Cyber-shot DSC-W80 Digital Camera

Access Message Whenever I turn the DSC-W70 on it displays a black screen and the word "Access." At the same time the lens extends and retracts, however unlike some of the other problems people are having, the lens is not getting stuck. Also I also notice a faint clicking/buzzing sound from within the camera when the lens is still and not retracting/extending. After about 10 seconds it begins to beep and displays the message "Turn the power off and on again." I am able to view previously taken ph

This is a hardware problem. Your simptons is tipical of a lens position sensor being faulty.\015\012\015\012There is however nothing you can do yourself. Contact your nearest Sony dealer and take the camera to a Sony service centre. ... Sony Cyber-shot DSC-W50 Digital Camera

I have a Photosmart R725 camera with some problems reading the card. Message on screen says "card unreadable" or "card unsupported". This occurs with a new card, and even with a card that I have been using already, and have hundreds of photos on. I have tried to find the answer to my problem in the book, to no avail. Please help. Card unreadable on screen, also unable to establish a connection with pc. This also occurs with a new card

You can contact HP through their online chat page. I have contacted them several times in regard to my HP camera and they are extremely helpful. You should still be able to contact them through this service even if your warranty has run out. Here is ... HP Photosmart R727 Digital Camera

Canon PowerShot A495 - Brand new. Used it once and took 40 photos. It then told me to change the batteries which I did. From then on it keeps saying "change the batteries" I've used alkalines and also rechargeable NiMH, These are either new or fully recharged batteries and still I get the same message. I have also cleaned the terminals inside the camera and even those on the batteries themselves. No change. This is clearly not a battery problem. This is a camera problem and its seems I am not th

... Canon PowerShot A430 Digital Camera

When I install a memory card in my camera I get the message read only memory card, remove write protection to capture or write to card. The switch on the memory card is in the correct position, this is a card that I have been using with no problems until now. I also installed a brand new memory card and got the same message. I think there's a problem internally with the camera.

... Kodak EasyShare Z740 Digital Camera

My casio exilim cant open the lens anymore.I think it was stuck up because of the sand.My cousin left it on the sand when were having our swimming last April 2010.And the big problem is that she left my digicam wid the lens opened and facing the sand.And while on the sand when she knew that it was still on she off it immediately.After that incident,the lens cant open anymore.Can it still be repair?....i dont know where to bring it,i dont have any idea where is the casio service center here but i

Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuu ... Casio Exilim Zoom EX-Z250 Digital Camera

Hey Guys, whenever I connect my Konica Minolta DiMAGE X60 to my PC (WinXP, Service Pack 3), I receive the following error message: "Power Surge On Hub Port". I already checked the internet to solve the problem, so I know how to get rid of the message box. But it doesn't solve the problem... I also tried to reinstall the drivers for the USB ports. Need help!

When i connect my KonicaMinolta Dimage 60 to my computer. camera does not go beyond Initialization. Has anyone had this problem? ... Konica Minolta DiMAGE X60 Digital Camera

Access Message Whenever I turn the DSC-W70 on it displays a black screen and the word "Access." At the same time the lens extends and retracts, however unlike some of the other problems people are having, the lens is not getting stuck. Also I also notice a faint clicking/buzzing sound from within the camera when the lens is still and not retracting/extending. After about 10 seconds it begins to beep and displays the message "Turn the power off and on again." I am able to view previously taken ph

Could not believe it but it worked for me as well. First time I see that a good smack makes it work ... Sony Cyber-shot DSC-W70 Digital Camera

There are several problems with my camera one of them is the fact in that Every time i turn on my Lumix 10x mega pixel camera the lens won't focus it also won't let me take any pictures. When i turn the camera off the lens won't go back into the camera but when i turn it back on the lens gos in and then out again. There is one more problem whenever i go to look at the pictures on play i can look through a few before its says "please turn camera off then on a again" it also says the same message

OK, if there is sand in the camera, the gears will bind or stop causing the error that you described. I think it needs to be taken apart and cleaned by a service center before using again. Or you could buy a spare caemera to use on your family holida ... Digital Cameras

Adding WD-40 Will adding a little bit of wd-50 to the camera zoom swivel head affect the camera? I probably should have sprayed it on a napkin and wiped it but I sprayed it directly on. But not much at all. But my camera has completely stopped working and its stuck with the zoom out and everything. But it might also be a battery problem since I dont have my battery charger and dont know if the camera died but I dont think it would die with the lens still exposed. I have a Sone DSC-W50. Please he

Gears hang up alot or the lens was banged while out make the lens stay out.. a tiny motor that drives these gears might be bad,\015\012might be a low battery, sometimes other errors make the camera just shut down with lens sticking out, I used ... Sony Cyber-shot DSC-W50 Digital Camera

Lens Error I recently had a problem with my Casio QV-R4... every time I'd turn it on, the lens would retract and I'd get a "LENS ERROR" message on the screen. I talked to customer support and they told me that Installing the new version of their firmware, v1.01 would fix this problem. I've since installed the new firmware version, but I am still receiving the lens error. Has anyone else encountered this problem? Does anyone know how to fix it? Please help!!!

As solutions 1 & 2 indicate, lubing the gears works!! This is a great camera, so I hope all of the QV-R4 owners try this. I may become a maintenance item for the camera.\015\012 \015\012I have a few a ... Casio QV-R4 Digital Camera

ERR message I have an err message that displays everytime i try to take a pic...i went through reset procedure and did not correct problem ..camera worked night before during a shoot..turned on next day and did not work...we dont have a nikon repair center anywhere close...i hope it something simple that can be fixed here ..it acts like its taking a pic, then message displays and goes off after about 20 sec

I'm afraid, according to the manual you have to send it in...\015\012I would contact Nikon either through their Web site or by phone. It is normally neither expensive nor complicated to send a camera in. Just pack it well to protect it and send ... Nikon D70SLR Camer Armor Smoke Digital Camera

I have put a sim card into my camera that I have used in the past but it says memory card error. I have also tried a brand new card and the message says the same. The only card that does not give the message is one I have in a digital photoframe with photos already on it. Do you know what the problem can be please ?

Trying to upload photos off the sim card on a sony camera. when the computer is posting the thumbnail shots it gets about half of the 600 or so and says "devise can not display thumbnail copies, device is busy?" Not sure how to extract the photos o ... Panasonic Lumix DMC-FX9 Digital Camera

Hi, after switching off the cam, I get a message saying ''lens error''. When I turn on I also hear strange ''bzz'' from the lens. How can I solve it? I've tried turn off and remove the battery but the problem remains ... What can I do? What is the problem? Thanks Carla

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Digital Cameras

When I turn the camera on I get the message "memory card error". The only button on the camera which then works is the menu button but it just brings up the screen and then the same error message. Yes, I have replaced the memory card and the first memory card works in our other camera so it is not a problem with the card. My computer also fails to recognise the camera when I connect it via the usb port. Any bright ideas?

You need to format the card in the camera. Go into the menu and scroll to "format" and follow the on-screen instructions. This will erase and initialize the card . To download pictures, the most trouble-free way is to use a card reader and download t ... Pentax Optio S4i Digital Camera

I have a Nikon Coolpix L14 and all of a sudden, when I turn it on, the lens moves in and out while making a strange noise until a "Lens Error" message comes on the screen. I tried replacing the batteries, turning it off and on, taking out the memory card, and cleaning the lens. The first time I replaced the batteries, it worked...until the next time I used it and the screen was completely blurred. Then, I had the original problem with the "Lens Error" message. I really don't think it is a conde

Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Nikon Coolpix L14 Digital Camera

Faulty d40x hi i bought a d40x off ebay the other day and couldnt wait to start snapping.... problems: - The error message "initialization error. Turn camera on and off again" appears. Upon turning the camera off and on again, the same message appears. After several times trying it still does not work. Also, the menu screen appears, and just keeps flicking from menu to menu constantly. As well as this, on the playback mode, the picture of the image displayed keeps zooming in as far as

I would start by looking at all of the push buttons on the camera. One may be stuck down. ... Nikon D40x Digital Camera

Hi. When I power up my Canon A75 to take a picture, the screen is purple, not black. Is this also a sensor problem? Also when the camera is turned on or off, the lens retraction or extension mechanism makes an odd noise in addition to the normal sound. As far as I know, this camera has not been dropped. Thanks for your help.

The purple screen is also an indication of sensor failure, However, the odd noise could any of a number of things from sand/gunk in the gear mechanism, a damaged tooth on a gear, etc... But still, recommend that you contact Canon to arrange the adv ... Canon PowerShot A75 Digital Camera

I am having trouble down loading my pictures, which was not a problem before. I now show on my desk top ACDsee 10-ACDsee7- ACD photo editor and ACD see 10 photo manager.' there was also a message that there were certain files that could be affected . It did take me almost a half hour to down load my pictures to night, which was rather frustrating to say the least. do I have to many ACD programes how do I correct the problem. I am almost at the point of trying to find another system.

Hello,\015\012Uninstall the ACD and then restart the system, after restarting reinstall the ACd back to the system. \015\012\015\012If your problem is only to copy or download pic from the camera to the PC. the computer detect autom ... Digital Cameras
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2943 seconds