Having problems with your Fuji FinePix 2650 Digital Camera ?
Zoom error///lens will not come out when you turn camera on
This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Zoom problem The camera I have don't allow the zoom to come out, when I turn camera on it says "zoom error" and then I can't do nothing on camera,not even look at pics I have taken. It does it alot, sometimes the camera will turn on without saying it,but it's very rare. And sometimes I can turn it on and it will say "zoom error" but if I press zoom in the camera will work. But it's very rare that it works. I love the camera and hope there is a solution.
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Zoom DualCam 1300 (1599) Digital Camera
I have a sp-560uz and when i turn on my camera, zoom error comes on and my camera turns off. I put brand new batteries and it worked for a while then zoom error comes on. i put some more batteries took a picture, turned it off and when i put it back on zoom error came back on.
Try the procedures in this tip. ... Olympus Digital Cameras
Hp945lens When I fix a wide angle lens to my camera and switch it on, the zoom tries to come out, fails and then turns the camera off. I'm assuming that because the screw-on lens is on the outer fixed lens this is stopping the zoom from coming out which then turns the camera off. What am I doing wrong?
Hi Do you use a lens tube? You need one of these so the lens does not hit the screw on lens when it extends. Quite cheap on ebay etc. Standard 55mm thread.Hope this helpsjbrevealsall ... HP Photosmart 945 Digital Camera
The entire zoom lens will not come out when I turn the camera on. It moves a little, makes a sound, and then my camera says turn off camera off and back on. I tried that several times and it is still not working. The battery is charged. I did go to the beach and wondering if sand got into the camera. I also cannot review my pictures as the message comes up about turning it off. What is the best solution?
HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Panasonic Lumix DMC-TZ3 Digital Camera
My camera's optical zoom isnt working. when i was on holiday little bits of sand got stuck in the zoom lens and now it wont come out and isnt allowing me to take pictures. the camera turns on, but comes up with a message saying "turn power off then on again."
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Sony Cyber-Shot DSC-S40 Digital Camera
I have a canon powershot A470 and it fell in water. after i removed the card and batteries of which still worked and neither were wet, i let the camera dry for a couple of days. it has turned on since and the screen would come on and show me the pics on the card but it kept turning itself off and the zoom lense would go in and out on it's own. now, i can't get the camera to turn on and the zoom lense it stuck. any ideas??? or should i call it a wash. i really love this camera!!! Theresa
I submerged my powershot for a couple of seconds. it did get completely wet. it was acting very strangely: the lcd wasn't working, the little orange light on the front kept flashing, and it took a few tries for the lens to extend.then ... Canon PowerShot A470 Digital Camera
Unfortunately I dropped my lumix camera today. The outer rim of the zoom part is a tiny bit dented. When I turn the camera on, the zoom tries to come out, hunts a little and then goes back in. The camera appears to be fine apart from the rim which I think may be rubbing on the side of the zoom. What can I do, does the outer rim come off? Thank you in advance, I am on holiday in India and devastated I can't take photos.
Hi, Sorry for that, but the only remedy is to replace the complete zoom assembly, it can not be repair on component level. Thanks for using fixya. ... Panasonic Lumix DMC-LZ2 Digital Camera
I dropped my panasonic camera onto the zoom lens. the zoom will not close, the shutter stays open. When I turn on the camera it says "please turn off camera and turn on again." When I do this the same message comes on again. Is it worth geting fixed?
... Digital Cameras
Only about 9 months after buying my camera, It wouldn't turn on. I'll plug it in and the light will come on that it's charging, but when I got to turn it on, it turns on for a split second (and the zoom lense comes out) and then it turns itself right back off (and the zoom lense goes in). I thought that it needed a new battery so I bought one and it's still doing the same thing. I emailed Kodak and they said that I should just send it into them for a $60 repair fee...lame. Any suggestions?
If its only been 9 months since you bought it shouldn't it be covered for repair? espically if its a manufactures fault,which it sounds like. ... Kodak EasyShare M863 Digital Camera
This Sucks! My camera is new, I went to use it...actually for something I saw that was hillariious...and I turned it on, the lens came out...it was zoomed all the way, and I could'nt take the pic nor could I adjust the zoom. Then I got this hateful message to turn camera off then on again, which I did. Now the lens does not return apon turning the power off, but does retract and come back out when I turn it on...and then the same scenario! Help Please!!!!!!!
I think this is just a hardware malfunction(some mech. switch) because, i have a lz7 and when i deliberately open the battery case with the camera power on it obviously switches off and then when u close the battery case either with the power on or o ... Panasonic Lumix DMC-LZ7 Digital Camera
Lens error My zoom will not work. I can take pictures if I don't zoom, but as soon as I try to zoom in, the screen goes black, the camera beeps a few times and a message that says "lens error, restart camera". However, upon restarting the camera, nothing changes - it still won't zoom!. Also, when turning on the camera, when the lens first comes out...it sounds funny, like it is puttering. Help?
Powershot S3 IS: lens error message, lens juddering on startup but not \015\012coming out. Tried all tricks on internet without success, so decided to \015\012dismantle camera. Localised fault to optical position encoder on first \015\012transfer gea ... Canon PowerShot S3 IS Digital Camera
Ok so i am turning on my camera (an Fe-340) and the lens go in two or three times then when the screen finally does come on it is blurry and way out of focus, also when i attempt to adjust the zoom the camera turns itself off, if i attempt to turn the camera off using the power button it goes off but the lens does not retract.All other functions on the camera are operating correctly to my knowledge i can even take a blurry out of focus picture, view it in display mode or even transfer it to my c
It may be something more serious, but the problem you describe is\015\012frequently due to corrosion on the battery contacts inside the camera. \015\012Remove the batteries and wipe the camera contacts firmly with a clean\015\012cloth (heavy corrosio ... Olympus FE-340 Digital Camera
Hello samsung l310w camera still does not work. this time the lens does not come out, when i turn on the camera. when i turn on the camera all it does is beeps twice and then turns itself off. please help, because my other camera is rubbish, and that one does not zoom in fully.
If you have recently dropped the camera you may have damaged the lens\015\012tube (housing). This damage will prevent the lens from moving properly\015\012and will cause the camera to shut itself off after a few seconds. If\015\012the lens is damag ... Digital Cameras
Just purchased an powershot SX1 IS. I took one photo, zoomed in on it to see how clear the zoom was once taken a photo. THen it switched itself of with the lens still out. Now when turning it on it has a black screen and say lens error...restart camera. I have tried holding func. when turning on the camera and the time comes up on the screen. But as soon as I let go of func I get the error msg.
Hello if you just purchased this unit Then i advise you to take it back, this sounds like a system control issue or main board problem. Holding the function key while turning is factory reset, if this is not working right them the camera has a bad sy ... Canon PowerShot SX1 IS Digital Camera
When I turn my camera on, the zoom does not come out, a "zoom error" appear on the display and the camera turns off by itself. I do not drop or knock it and the batteries are new. thank you for your help! Jack
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will have to get it fixed by a professional.Use\015\012\015\012\ ... Digital Cameras
Olympus FE-280 I can no longer take photos with my camera! When I turn it on it makes some weird noises as the zoom lens adjusts, and then the viewer screen is blurry when it comes on. If I try to zoom in or zoom out, the camera simply shuts off. I can view pictures that I have already taken, and the battery is charged. What's going on?! Camera bought at Christmas 2007, is this covered under warranty??
1 year warranty on olympus products, but does not cover physical damage such as impact, water, or sand ... Olympus FE-280 Digital Camera
Zoom ERROR When I turn my Camera on it comes up saying Zoom Error. I can't Zoom in or out - and all I can see is a black screen. Last time I used it - I took a picture and put it bck in my bag - when I pulled it out again the error msg came up. It has happened once before and I reset the camera through the menu and the msg went away and the camera went bck to normal so when it happened again I press reset but this time it hasn't made a difference. Any suggestions?
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will have to get it fixed by a pro ... Fuji FinePix A820 Digital Camera
Zoom lens cannot go in. camera cannot be turn on with new battery. after turning on the camera, the lens comes out. however, the camera does not turn on. after changing new battery, nothing happens after pressing on/off button.
Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Casio QV-R51 Digital Camera
Digital camera I have a digital camera (Pentax Optio A10) and just recently the camera stop working. Every time I turn on the power button, the lens zoom out and a few seconds later the camera will turn off, and the lens will come back in. I bought a new battery thinking it help, but it still does the same thing. The camera is not even 2 years old yet and I paid over $300 for it. HELP?!?!
I had almost similar problems with my A10 from day one. The camera shuts down before the battery is depleted, most of the time while I was operating the zoomlens. I bought a new battery, but that didn't solve it. Later I decided to take it apart as a ... Pentax Optio A10 Digital Camera
Can't zoom! I can no longer take photos with my camera! When I turn it on it makes some weird noises as the zoom lens adjusts, and then the viewer screen is blurry when it comes on. If I try to zoom in or zoom out, the camera simply shuts off. I can view pictures that I have already taken, and the battery is charged. What's going on?!
I had the same problem, I sent it to Olympus. The camers working fine one evening and the above problem in the morning after insrtalling charged battery.syed ... Olympus FE-280 Digital Camera
The zoom won't come out when I try to turn my camera on, it just turns a little bit, then turns back to the original place, and the screen says zoom error. I've tried different batteries, and taking out the memory card and putting it back in. The model is FujiFilm; FinePix A400. What should I do?
Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. O ... Digital Cameras
PANASONIC - fmc-fs5 When I turn the camera on, it comes up and then says "Please turn camera off and then on again". Looks like it is trying to recover from an internal error. Maybe I can reset the camera's computer? It also is doing a focus back and forth thing like it's zooming back and forth.
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is t ... Panasonic Lumix DMC-FS5 Digital Camera
I have an Olympus Camedia C-50 Zoom camera that has worked fine for a few years, but suddenly when I open the lens cover, the camera does not turn on. I charged the battery and it is fine, and I can use the quick view button in the back to see what I have already taken, but the lens will not come out and turn the camera on. What can I do?
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Olympus Camedia C-50 Zoom Digital Camera
Cyber-Shot Dsc-W70 hi the lens won't come out i have to pull it to get it to come out then its all blurry and when i try to zoom it turns to a black screen and says turn off camera and try again and when the lens doesn't come out it does the same thing
Hi \015\012\015\012You probably have a faulty lens unit. You can make sure of this by checking that the spaces between the two rings that extend forward at switch on has the same distance between each other. \015\012\015\012If ... Sony Cyber-Shot DSC-F717 Digital Camera
When I switch ON my camera, zoom comes out then comes in for three times then the massage ''TURN THE POWER OFF AND ON AGAIN' appears on display. I tried to switch it OFF and ON but still it's not working. How could I fix my camera please?
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is t ... Sony Cyber-shot DSC-W170 Digital Camera