Having problems with your Fuji FinePix A360 Digital Camera ?

I keep getting a zoom error message. I turn the camera on and off and this still occurs.


Answers :

First off how long have you owned the camera? Just to confirm it is a Fuji finepix a360. This means most likely it was dropped or banged with the lens extended out. There are a few things you can try and do yourself. If its under a year old it still has a warranty. If not you can still have it repaired by fuji or an independent repair service.

If your camera is still under warranty, the best thing you can do is to take it to the nearest official repair shop and they should fix it for free.
If your camera is out of warranty, or if the manufacturer refuses to repair it for free (happens sometimes if for example they suspect the camera has not been treated properly) you can try the following methods to repair it yourself.

First, make sure your camera has fresh batteries and it is in recording mode.

Remove the batteries from the camera, wait for a couple of minutes, then put them back in and turn the camera on.

Try compressed air. With a fine tip blow off gun and dry compressed air (20 lbs) set the tip between the lens turret and the camera body and turn on the air while moving the tip around the lens. It should remove all dust and sand. Turn the camera on and it should function fine.
Another method is to tap the padded USB cover part on a hard surface, for example, a desk. Sounds simple, but it works.

Try forcing the camera lens. Turn off the camera. Place it on the back with the lens facing up and take a look at the spacing between the lens and the lens housing. If you notice that the gap is not even all the way around the lens, the problem should be easy to fix. This type of a problem usually occurs if the camera was dropped while the lens was extended. Simply - VERY GENTLY - press down the lens on the side where the gap is the biggest. You should hear a "click" as it pops back into place. Try powering the camera back on.

If the lens doesn't extend at all or it extends, and then retracts again, do the following. Turn the camera off. Take the camera in one hand and with the other gently take one part of the lens and gently move it round in a circular movement. Do so with both sections of the lens. You will hear a "click" as it pops back in place. Power the camera on.

Another version of this fix would be to pull and twist on the largest ring of the lens while turning the camera on. Listen for a "click". If at first the focus seems to be off, turn the camera on and off and take lots of pictures, close ups and distance. Focus should slowly start improving.
Please let me know if you need any further assistance.
Thanks,
Lee
Repair Help & Product Troubleshooting for Fuji FinePix A360 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I keep getting a zoom error message. I turn the camera on and off and this still occurs.


First off how long have you owned the camera? Just to confirm it is a Fuji finepix a360. This means most likely it was dropped or banged with the lens extended out. There are a few things you can try and do yourself. If its under a year old it still ... Fuji FinePix A360 Digital Camera

I have a Nikon S6 digital camera, everything about the camera seems to work fine, except for this "lens error" message I keep getting. Sometimes I'll turn it on, and I can use it just fine. But then there are other times where I have to turn it off and on in order to get it to work. And then there are those times where turning it off and on don't help. I usually give up and try again later. Sometimes it'll still give that error message, and other times, it will just work like normal. What can


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Nikon COOLPIX S6 Digital Camera

Faulty d40x hi i bought a d40x off ebay the other day and couldnt wait to start snapping.... problems: - The error message "initialization error. Turn camera on and off again" appears. Upon turning the camera off and on again, the same message appears. After several times trying it still does not work. Also, the menu screen appears, and just keeps flicking from menu to menu constantly. As well as this, on the playback mode, the picture of the image displayed keeps zooming in as far as


I would start by looking at all of the push buttons on the camera. One may be stuck down. ... Nikon D40x Digital Camera

Zoom Error When I turn my camera on I keep getting a 'Zoom Error' message. Did I push a button to cause this? How do I get rid of this error message (unable to take pictures). Thanks!


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a p ... Fuji FinePix 2800 Zoom Digital Camera

Optio E10 When I turn my camera on I get an error message that says "memory card error", I purchased a new memory card but still get the same error message...any suggestions? I have the exact same problem with my Pentax Optio S7. I turn on the camera and it displays the message Memory Card Error. I have tried several new cards and get the same message. There is an option on the menu to format a card, but you can't access the menu if you have the card installed. It takes great pictures without t


HelloOK, if the memory card itself is locked, you might \012sometimes get this error code. All you need to do is to take out the \012memory card and switch the lever on the left side to the unlock. ... Pentax Optio S7 Digital Camera

Panasonic lumix DMC-FX01..zoom stopped working. When I try to zoom I get an error message to turn camera off and back on. This doesn't work. Camera still works fine in regular mode. Is the zoom fixable?


... Panasonic Lumix DMC-FX01 Digital Camera

Memory card errors. I turn it on and get message MEMORY CARD ERROR PLEASE CHECK CARD. Occurs on different cards. Sometimes I can clean the contacts on the card and it will work. Sometimes, I can take pictures but if I remove the card it cannot be read if install it back or by a computer or printer. I use the camera as publicity in trade shows taking then printing pictures, so the cards are removed and inserted constantly. I have reformatted the card in the camera, still fails.


Hi wait a moment pls your request is been proceeding.. ... Panasonic Lumix DMC-FZ18 Digital Camera

When ever I try to use the zoom button I get a message saying system error (zoom) I have also gotten a message that says Please turn off camera and turn on again... What is going on with my camera and what needs to happen to get it fixed!


When you first switch on the camera the lens will motor forward?\015\012\015\012If it does so then either the zoom control button is faulty or the control pcb \015\012\015\012If the lens does not move on first switch on then i ... Panasonic Lumix DMC-FZ28 Digital Camera

Keep getting a message saying zoom error - camera turns on, but zoom lens not working


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will have to get it fixed by a pro ... Fuji FinePix S1000FD Digital Camera

We have installed new xD-Picture Card M2GB into Olympus Digital Camera Model No. C-750 Ultra Zoom not work, Screen mentioned Card Error I purchased a 1GB Sandisk (used camera) but when I power camera on I get a "Card ERROR" message. The very first time I powered up I programmed the date and time....but then got the error message. Now I get it every time I turn it on. I don't have another card to test it with:(


Go here\015\012http://www.casio.com/home ... Casio QV-R40 Digital Camera

Zoom error Today after using my camera for awhile the back screen displayed "zoom error" and a little sound whirled. Then the camera shut off by itself. I turned it on and off a couple of times, but without success. The lens is extended and will not withdraw back into the camera. I have taken out the batteries and re-inserted them. Finally, I gently pushed the lenses back to the body of the camera (as they seemed to be trying to go back to the camera), I am still getting the zoom error reading a


You may be true that sand must be creating this problem, as this happens very often. the sand enters into the lense assembly, creating friction in the movement. if this has happened total dismantelling and cleaning of the lense assembly will solve t ... Olympus Camedia C-350 Digital Camera

I have a Canon Power Shot SX120 IS camera. I turned it on and the lens open a portion of the way and I got an error message that say, "Lens Error Restart Camera". I put fresh batteries in it this morning and have only taken about 10 pic's. I turned the camera off and removed the batteries then replaced with new ones but I still get same message. Please advise if you can.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon PowerShot SX100 IS Digital Camera

Lens error My zoom will not work. I can take pictures if I don't zoom, but as soon as I try to zoom in, the screen goes black, the camera beeps a few times and a message that says "lens error, restart camera". However, upon restarting the camera, nothing changes - it still won't zoom!. Also, when turning on the camera, when the lens first comes out...it sounds funny, like it is puttering. Help?


Powershot S3 IS: lens error message, lens juddering on startup but not \015\012coming out. Tried all tricks on internet without success, so decided to \015\012dismantle camera. Localised fault to optical position encoder on first \015\012transfer gea ... Canon PowerShot S3 IS Digital Camera

Error Message Hello! Every time I turn My Sony camera on it starts beeping and and giving me the error message "Turn the power off and on again." I've tried turning it off and back on, along with taking the battery out and putting it back in and even pressing the reset button and I'm still continuing to get the same error message. Any ideas on what I can try next?


I have the same problem ... Sony Cyber-Shot DSC-L1 Digital Camera

Just purchased an powershot SX1 IS. I took one photo, zoomed in on it to see how clear the zoom was once taken a photo. THen it switched itself of with the lens still out. Now when turning it on it has a black screen and say lens error...restart camera. I have tried holding func. when turning on the camera and the time comes up on the screen. But as soon as I let go of func I get the error msg.


Hello if you just purchased this unit Then i advise you to take it back, this sounds like a system control issue or main board problem. Holding the function key while turning is factory reset, if this is not working right them the camera has a bad sy ... Canon PowerShot SX1 IS Digital Camera

When turning off the camera, the lens does not retract. I also get an error message "SYSTEM ERROR (ZOOM)" and another one "PLEASE TURN THE CAMERA OFF AND THEN ON". Once the camera is turned on, I can hear the lens mechanism working, but obviously failing.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Panasonic DMC-FX37 Digital Camera

Incompatible jpeg I don't know much about cameras. My daughter was getting this error on her canon so she could not review her pictures. She tried putting her memory card in my canon and we still got the same message. We were able to get the pictures saved by putting the memory card in the computer. Anyways now I keep getting that message on my camera with my own memory card. What could hers have done to mine?? what can i do so i can view them again in my camera without that jpeg incompatible s


Hi thereSave all the pictures to the computer, then format both cards using the menu in the camera, then take a picture and see if it takes them well.Good luck and thanks for using Fixya!!!! ... Canon PowerShot SD1100 IS Digital Camera

Panasonic Lumix DMC-LZ2 Image 'melts' into streaky vertical lines when camera is turned on. This problem started occuring immediately after I found my kids deliberately turning the camera off while jamming the lens cover open, so they could get the 'turn camera off and then on again' error message (yes, I know - they've been banned from touching it again). I confiscated the camera, turned it off and it sat unused for about 3 days. When it was next turned on, the image on the LCD screen was


... Panasonic Lumix DMC-LZ2 Digital Camera

Lumix DMC-ZR1 When I turn the camera on, I get a message telling me to turn it off and turn it on again. It does not focus, and the EZ zoom shows all the time whether I press the button or not. I also get a "system error ( focus) " message.


This is a lens mechanism fault. USe can of air and spray on surrounding the lens For cleaning the dust. and then try. ... Panasonic Lumix DMC-FZ28 Digital Camera

Error message When I turn camera on I get following error message; Error 00-00-00 30-00-28 No idea what this means . I can still use playback function to look at photos but can't bring up screen to take photos. I thought it was because memory card was full but have since deleted heaps of photos and it still doesn't work.


... Ricoh Caplio RZ1 Digital Camera

After uploading pictures from my camera to my pc yesterday, the zoom lens will no longer retract into the camera. I do get a message on the screen of the camera that says turn the power off and on again. I have tried everything, and still no luck. I have plugged it back into the pc, I have charged it, and have turned the power on and off at all options, and it still will not retract.


I believe its a sony cam. this generally happens if you have dropped it. when the message comes. try tapping the camera. if it works then you are lucky. if not then you have to change the lens array. it costs about 60$ ... Sony Digital Cameras

Incompatible jpeg I don't know much about cameras. My daughter was getting this error on her canon so she could not review her pictures. She tried putting her memory card in my canon and we still got the same message. We were able to get the pictures saved by putting the memory card in the computer. Anyways now I keep getting that message on my camera with my own memory card. What could hers have done to mine??


Did you transfer the pictures back and forth from the camera to computer before you noticed this? If you did that, you would be changing the format that the camera recognizes thus preventing you to review those pictures on your camera again. This is ... Canon PowerShot SD750 / IXUS 75 Digital Camera

Hi, I have a panasonic Lumix, DMC-FS5 digital camera. When I turn the camera on and it's on 'photograph' mode, a message keeps appearing after a couple of seconds saying: "please turn camera off and then on again". I get the same message everytime and am unable to take any photos or even access the menu options. There are no problems when the mode is set to 'playback' mode. The images are still there and I can scroll through, as well as access the menu.


Hi,I had this same problem. I have just pulled the lense (not with any major strength) when it was fully extended. This seems to have solved it for me!! ... Panasonic Lumix DMC-FS5 Digital Camera

Optio E10 When I turn my camera on I get an error message that says "memory card error", I purchased a new memory card but still get the same error message...any suggestions?


HelloOK, if the memory card itself is locked, you might \012sometimes get this error code. All you need to do is to take out the \012memory card and switch the lever on the left side to the unlock. ... Pentax Optio E10 Digital Camera

Canon A400 Hi, I have the above camera (canon power shot A400) and have just solved the E18 error by tapping the plastic A/V out cover - THANK YOU ! However, now, although the camera turns on, lense extends and I get full working order - after a few minutes I get the message 'Change batteriers'. and the camera dies. I have now put in several new batteries (including the little(cr1220) but the same message keeps coming up and the screen and the whole thing dies after a few seconds. Is this a furt


Having using standard LR6 batteries in a Canon before you will only get 3 or 4 pics max before it drains the batteries. You really need high power AA's like 2300mAH+ rechargeables for any good performance or Lithium AA's ... Canon PowerShot A400 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5486 seconds