Having problems with your Fuji FinePix A820 Digital Camera ?

I have a fuji A820 and when the power button is pressed with fresh batteries it will turn on for a second then shut down. the camera will not stay turned on

Answers :

Fixing a Lens Error on a Digital Camera
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Fuji FinePix A820 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Canon A510 Powershot camera will not stay powered on when I turn it on in picture-review mode. It comes on for a second --> Canon screen flashes on -- and then shuts off. In picture-taking mode, it seems to be fine. It stays on. But if I switch to review mode, it turns off. I've changed the batteries. It was fine last time I used it, last week. I left it plugged into the PC for a few days, if that makes any difference.

These cameras have capacitors built into the circuitry. A capacitor holds a higher voltage so the camera will operate when in use. Some modes in these cameras do need a higher voltage to work. The capacitor for the review mode is weak and will need t ... Digital Cameras

Canon power shut A520 - When I turn on my camara it stays on for only 30 seconds, the blue screen stays on and the lens part wont open ,its stuck,, then the camara just turns back off with ti ti ti noise , when i shake the camera i hear a tiny something loose inside ??? thank you very much for your help

Did you get it serviced lately ... Canon PowerShot A520 Digital Camera

I have a fuji A820 and when the power button is pressed with fresh batteries it will turn on for a second then shut down. the camera will not stay turned on

Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Fuji FinePix A820 Digital Camera

I have reset the camera and it still gets the error code 00000018-4489-957-000 when I try to turn it on. It will only stay on while it is connected to the power cord and only stays on for a second then shuts right back off?

I have checked HP references and they as you already know, have no data published for such an error code.\015\012\015\012If you have tried a new battery, and have no luck powering on the camera, I'm suspecting either a problem with the AC adapt ... HP Photosmart R727 Digital Camera

My camera is all messed up It's a Pentax Optio Z10. When I turn it on it is stuck in "Green Mode" then after a few seconds, turns off. If I press the "Playback" button it will come on and I can review pictures, but can't take new ones. When I close the slider the power stays on. I have to remove battery to shut it down. Looks like lots of other people have had this problem but I haven't seen one good solution . Please help

Hi,The problem you describe indicates that inner switch mechanism is broken that's why the camera turns off. You need to replace the inner switch so it will work properly. You need to take to near by the service center to get it rep ... Pentax Optio Z10 Digital Camera

Power doesn't work properly. When I turn off camera with power button, lense stays out. When I turn on, the lense goes in then back out again, but after a few seconds, I get the message: "Please turn camera off then on again." If I don't do anything, the camera will turn off by itself, and the lense will go in. Battery is fully charged, and nothing dramatic happened to start this problem...

HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Panasonic Lumix DMC-FX8 Digital Camera

Power issues. Just recently I've encountered a problem with my camera. After plugging it into my computer (And not noticing the power surge notification on the desktop while doing so). It locked up and powered itself off. I tried turning it back on, and it turned on for a split second then shut off without retracting the lense. I switched batteries and it retracted the lense, but I tried powering it on and the lense only came halfway out and it powered off. I've tried 4 fresh sets of batteries a

You sdaid power surge on the laptop.\015\012Thus suggests that this may have affected the camrera.\015\012I would think a 'repair' if such is possible will be near the cost of replacement.\015\012Only Olympus can advise ... Olympus FE-115 Digital Camera

When the camera is turned on with the power button the lens comes out and stays out but the camera immediately shuts off and the lens stays open. The only time the camera remains on is when the dial at the top is in the position to view the pictures already on the camera.

Please try Power Resetting the Camera. To Power Reset the Camera, First, please turn OFF the Camera.Then, remove the battery pack from the Camera.Then, press and hold the POWER button on the Camera for 30 seconds.Then, reinser ... Sony Digital Cameras

My sony digital camera won't fully turn on. when you push power the screen stays black but it says access and the lenses repetitively goes in and out with a 3 second pause between. then finally it stops and says to turn the camera off then back one. but this keeps occuring and it won't fully turn on. HELP!

There is some problem with your sensor in lens so only you are getting this problem .......so better check the sensor..... ... Digital Cameras

My camera will not stay on. It turns on for about two seconds, the screen says Sanyo then shuts off. I took the camera apart to clean it and to make sure it didn't get wet and the problem still isn't resolved. The 3X optical zoom is also stuck out and when I turn the camera on, it sounds like it is trying to pull it back in but can't

If you actually took the camera apart, you may have damaged some components. You also might be the luckiest person ever and no damage was caused. In that case, try these:\012\012 ... Sanyo Digital Cameras

When i power on the Camera F72 EXR it comes up with an Error message that says turn camera off and then turn back on, i do that an the same error keeps popping up, also when camera shuts off the lense fails to collaps and stays open in the off position

Whenever I've seen that before it's caused by the camera being dropped on its lens while the lens was out. It can be repaired though it's fairly expensive too, in my honest opinion you'd be better off getting a new camera. ... Digital Cameras

When Mode switch is set to take pictures or clips, the camera shuts down in less than a second after I turn it on. If the Mode switch is in the far-left position (review pictures already taken), it stays on and I can see all the pics in the camera, but as soon as I switch to picture-taking mode the camera shuts down.

Since u say ur having difficulty reassembling the unit back.... please refer the following.... it shows disassembly procedures for a similar model camera... this is as far the closest i could find to help you reassembling the unit... just apply rever ... Sony Cyber-Shot DSC-S40 Digital Camera

Camera problem What do you recommend I do, I was turning my camera on and the lense would close by itself and the power would shut off by itself. But now the lense stayed open and the camera still shuts off by itself.

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Kodak EASYSHARE M1063 Digital Camera

EX-S500: * I turn it on and the 'Adjust' screen comes up. *I press the 'Menu' and the lens comes out, the green light flashes for awhile, it beeps a few times, it grinds a few times and shuts off. The lens stays out. *I turn it back on, the lens goes back in and the 'Adjust' screen comes on. * I press the power button and the camera goes off. *I left the camera in the charge gradle all night and the battery did not charge. *Help

You could have a power and lens issue, going on at the same time here. There's a couple of web blogs that delineate things you can try to correct these issues, and here they are:\015\012 ... Casio Exilim EX-S500 Digital Camera

When I turn on my Kodak Z740 camera it only stays on for about 3 seconds then it shuts off completely. When I turn it on, the lens moves out then back in, then shuts off. The battery is one I bought fairly recently, I tried taking it out, leaving it out for seversl hours and putting it back in, this did not help.

HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Kodak EasyShare Z740 Digital Camera

My Kodak V1233, isn't working right. If I turn it on, it will only turn on a second and extend the lense and then shuts off (it's fully charged). I can eventually get to take pictures, if I start by hitting the favorite button, and then the camcorder button and then quickly hitting the the camera button. I can take pictures, but can't see them, I only see a black screen. The camera will not power off this way. If I take the battery out, and then put it back in, and hit the favorite button,

I have had the exact same problem this seems to be a common flaw in this model i do not suggest any one purchase the V1233 ... Kodak EasyShare V1233 Digital Camera

The camera will not power on. I have replaced the battery made sure it has a full charge, but when I insert it and try to turn it on the power light comes on for 10-12 seconds then shuts down.

... Kodak EasyShare Z612 Digital Camera

I have a Samsung L100. Its only a couple of months old and its never been dropped or damaged. When I turn it on, the power button turns blue, the lens opens, then it beeps two or three times and the shuts down - except that the blue light stays on. You can't use it and it you can't turn it off all the way without pulling the battery out. The screen doesn't light up or anything. The camera is totally useless now. I've found a few reviews online that say theirs do the same thing. Is there a

... Digital Cameras

Blank screen When I turn the camera on the screen is black..the green power light is on, but after a few seconds it shuts off. The camera is new and worked fine at first. We did the trouble shooting in the users manual but it didn't solve our problem. The battries are new and both at full charge.

The build of S50 is similar to S6, especially the lens. I fixed my S6.\015\012\015\012 \015\012\015\012If you want to follow my way to try fixing it yourself, keep reading and do it at your own risk. You paid several hundread do ... Nikon Coolpix S50 Digital Camera

I have a Sony DSLR-300. I lost the separate battery charger and bought an AC adapter that plugs directly into the camera. When I plug it into the adapter a red light comes on for 1 second then shuts off. The camera turns on while plugged in but won't stay on when I unplug it after I've had it on charge for 30 minutes. Any suggestions? I'm not even sure if the battery charges through plugging it in directly to the outlet rather than a separate battery charger?

The camera does NOT charge the battery. You do need to use a separate battery charger, such as one available from here. ... Sony Alpha DSLR-A300 Digital Camera

The camera will not stay turned on and when I press the power button the top buttons light up but the screen stays black and then immeadiatly shuts back off

... Kodak EASYSHARE V1253 Digital Camera

Camera wont turn on zoom lens is stuck out camera power light comes on flashes for a few second the screen shows a E18 then it shuts itself down

The lens motor or drive has failed. Thats why you are getting the error and the lens won't retact.This is covered under warrenty if you have any. If not it can cost more than a new camera to get fixed. If you conact canon support or conac ... Canon PowerShot A410 Digital Camera

Hi---our Digimax won't stay powered up, even with fresh batteries. When the power button is pushed, we get a green light for about two seconds, then camera shuts down. Any tips?

Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Samsung Digimax A503 Digital Camera

My camera won't turn on and the lens is stuck out. I've changed the batteries and it still won't stay on. The power light clicks on for a second then turns off. Help

Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Samsung Digimax S630 Digital Camera

Yes in my new sx30 IS I opened it new put the battery in it and a chip, and turned it on, powered up ok, then the lense Loudly shakes and after a few seconds the LED readout says lense error, camera will shut down which it does. I restart it again and the same thing happens. Can you help or did I just get a defective camera?

More than likely it sounds like you have a defective camera. ... Canon PowerShot SX30 IS Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 1.0308 seconds