Having problems with your Fuji FinePix A900 Digital Camera ?

Camera "switches off" when shutter release pressed but lens does not retract. Happens in all modes. Battery power is good.


Answers :

Fixing a Lens Error on a Digital Camera
\012
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Fuji FinePix A900 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Camera "switches off" when shutter release pressed but lens does not retract. Happens in all modes. Battery power is good.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Fuji FinePix A900 Digital Camera

MY FUJIFILM AV1OO DIGITAL CAMERA IS NOT WORKING PROPERLY AS SOON AS BATTERY IS INSERTED IT GETTING POWER ON AND TAKING TO PLAY MODE. FOR SHOOTING MODE IF I PRESS SHUTTER IT BLINKING RED LED AND SHOWING "PRESS SHUTTER BUTTON FOR SHOOTING MODE" NOTHING HAPPENING


... FUJIFILM FinePix AV100 Digital Camera

Displays all white in all modes. Kodak V570. Turn the power on and all I can see is white. I have tried a different battery an no battery, just power cord. I know the camera good enough I can go into the menu options and select some different features without actually seeing the menu. All that seems to work fine and the lens is working ok. I can push the shutter button, the flash goes off. I can't see the photo on the camera, but I can see the photo if I put the SD card into my computer. Please


Displays all white because all the color screen have RGB mode if any of mode's are not work correctlly it's mean's color chip was fail and not working. u have to repair ur camera and change ur display screen. ... Kodak EasyShare V570 Digital Camera

SONY DSC-S600 Sorry, no actual error -- what happens is this:- Power on camera, message comes up "Turn the power off and on again". Tried this-no good. New batteries-still no good. Sometimes it will start with an "Access" screen and then go into the "Turn the power off" message. Hope this explains the prob better Regards Sandra


If you are able to access the MENU option, then try to initilize the camera by following the steps mentioned below: \015\012\015\012Please press MENU to display the menu items.\015\012Please go to the SETUP menu and select the SETUP ... Sony Cyber-shot DSC-S600 Digital Camera

Sony DSC-S600 Sorrry! What happens is this:- Turn camera on,Cybershot screen opens up with musical jingle then it will say "Access" then another screen opens up saying "Turn power off and on again". Sometimes you don't get the "Access" and it will go straight into the "Power off and on again" screen. Tried this - no good. Changed batteries for fully charged brand new 2700mAh NIMH - 1.2V Uniross - still no good ! Any advice would be appreciated. Regards


If you have a memory card in the camera, take it out before turning the camera on ... Sony Cyber-shot DSC-S600 Digital Camera

Camera was on, working fine. When powering off, telescoping lens did not retract so lens remained extended just a bit with lens cover open. Waited a few minutes, turned it back on and I get the "access" display message then the beeps and (turn power off and back on) message. While off, I have removed the battery, replacing it with a fully charged spare and it still does this. The lens tries to telescope a little bit and retracts a touch, but I can't get the camera out of this mode. Can it be res


Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Sony Cyber-shot DSC-W55 Digital Camera

I have a kodak m1033 that suddenly doesn't do any functions once it is powered on. I have changed the battery and swapped out battery and memory card with another known good M1033. it will not zoom, allow mode change, go to menu. just get a chance to take one picture then it freezes up until it is powered off again but still won't zoom or perform any other functions.


After some really frustrating hours on Internet I managed to solve the\015\012problem myself. 1.Connect the camera to your pc and let it charge.\015\0122.Switch on the camera and let it be detected by the pc. 3.Pull the USB\015\012out while you leave ... Kodak EasyShare M1033 Digital Camera

When you press the power on button the camera lens starts to move out stops goes in then out again stops the screen does not illuminate at all.IF you then press the power button the lens tries to retract slightly but then stops and again nothing else happens. battery is fully charged. if you press the replay button screen and camera behaves as normal and you can view the pictures taken lens usually retracts all the way to its docked position again if it was nearly all the way out.


... Sea and Sea UNDERWATER DIGITAL CAMERA DX-1G Scuba Gear Cameras

I have a Canon EOS 40D When I switch it on all appears fine. When I take a photo the shutter remains open & all power is lost. I then need to remove & re-install the battery to recover power. I can view existing photos on the memory card but as soon as I switch to take a photo & click the shutter, the above happens again. Before I decide next steps I was hoping someone out there could help.


See if the problem is related to the memory card. Start by ejecting the memory card and after saving to disk via card reader, format the card. If there is a problem writing to the card, it will probably show up during the format process. Or, inser ... Canon EOS 40D Digital Camera

MJU 300 Hello my partners MJU 300 camera has developed a fault where when the shutter slide is opened it starts as normal the lens extends the lcd starts then allmost imediately the lens retracts. if it does stay out/on as soon as you take a photo it retracts & shuts down. i have tried a different battery same thing happens. so in my wisdom i decided to remove the shutter slider cover in the hope of finding some fluff on a switch but unfortunately it has only worsened the problem now the camera


Sean \015\012\015\012 Sorry about this but Olympus charge \302\243100 flat rate for all repairs- costly i thought. however i opted for buying a replacement from Ebay \302\24330 as good as new. seems a real waste but looks like olympus run an almost d ... Olympus MJU 300 Digital Camera

Canon SD1100 digital camera is completely dead. Nothing happens when I press the power button. Battery is good. Battery door switch is in good working order. I need to check for bad (blown) fuses on main board but where ? If you are not familiar with this camera and know how to fix it, please don't respond.


... Canon PowerShot SD1100 IS Digital Camera

Power problem I was charging camera using 4.5 DC volt socket on Camera, next I switch on camera so Lens head came out, accidentally power pin came off from camera and lens will not go back. Now nothing happening to camera when power cord connected or with battery, camera will not switch on at all including power lite does not come on with power cord connected. Look like it may have blown fuse in camera or something else serious. Any solution which I can try? I'm a very handy man with good too


I sounds like coincidently something in the camera failed. I doubt very much that simply pulling the power from the camera would cause damage. \015\012\015\012In anycase, if you were to open the camera, you would see that all the circuit ... Olympus FE-220 Digital Camera

Good evening I'm in Lima Peru on a medical mission away from the US for two weeks. I am on my 2nd week and my Nikon D200 stopped working. Before I left I thought the batteries were old and I replaced them with new nikon en-el3e. At home i could charge both batteries put them in and when i pressed the shutter button the control panel would go blank and I would have no power. I bought the new batteries and it worked fine for about 150 shots down here now it won't turn on at all both batteries are


Sorry to hear about your camera. Hope you already fixed it. If not, could you please precise what lens are you using? What are the precise description of the last "black out"? Please try to be as precise as possible(Circumstances/Was it inside or out ... Nikon D200 Body Only Digital Camera

Canon Powershot SD450 E18 problem: The camera lense would not open and reported error code E18 on power-up and then would shut down. I followed a procedure on the web for this issue and got the camera lens to open and it was working (able to take pictures for about a minute). When I powered down, the lense did not completely retract. I tried re-powering on but nothing happened. The camera is not getting any power. I figured the battery died so I re-charged it. I put the fully charged batt


... Canon Digital Cameras

MFH-CDC When a fresh or old battery is replaced the DATE/TIME is displayed. From this point on you can't change the mode. It seems that if the battery meter doesn't reflect battery power then the camera doesn't work! I seem to have this problem when the weather turns colder. Have had this happen to other cameras as well.


Turn it off, remove the disk and turn it back on. I have several of these that do the same thing and this usally works. Once the battery meter lights up you should be able to insert the disk and switch it to auto. For some reason sometimes it does ... Moultrie MFH-DGS-100 Digital Camera

My canon TX1 is about two years old. I recently went to use it and its not working properly. I can put it in play back mode manual mode or scn mode. As soon as I turn it to auto which I normally use the screen goes black and the power goes off although the lens does not retract. The battery is fully charged. Any suggestions?


... Canon PowerShot TX1 Digital Camera

The flash no longer works. In "auto" and in either the "auto flash" mode or "forced flash" mode no flash occurs. It is not in "suppressed flash" in the "portrait" screen position mode. The batteries are good. The shutter button is pressed after the charging is completed. The camera is not in "continuous shooting."


Hi there, \012Well first of all try to reset your camera, remove the battery from your camera for 4 hours and then insert them again, it helps you to do a hard reset in your camera. if further you have the same problem then there mus ... Fuji FinePix 3800 Digital Camera

Camera will not power on with power button. Batteries are good and memory card is in. Green power light flickers once but nothing else happens. Help?!?


... Samsung Digimax 430 Digital Camera

I have a Toshiba PDR-M700. I cannot get the camera to power on in any mode. Batteries are good and inserted correctly. It was working properly but after turning it off, I couldn't get it to power on again.


... Toshiba PDR-M700 Digital Camera

My easyshare camera drains batteries every other usage. but right now I put new batteriers in several times and I hear it start but nothing happens the shutter doesnt open and nothing comes on. I just got this camera in april and may have used it six times. I am very careful with my things and take good care of them. This has never been dropped and I keep it in the house when not in use.


If you have already tried changing the batteries you may not need to get it checked to a service center, as you bought 7 months ago you have the warrenty of the device so you will get a free of charge servicing as there is no physican damage\01 ... Kodak EasyShare C613 Digital Camera

Lens stuck... Recently while taking photos with my camera, I went to power it off when I was finished. It would not power off, and the lens is stuck...it will not retract. I changed batteries and that did not help. Should I take it somewhere for repair, or has this happened to anyone else?


This happens since the lens section assembly is damages. and this can be corrected by doing a proper service to it. and hence i recommend u to take it to some service center for repair. ... Olympus SP-350 Digital Camera

Wont turn on, shutter open at all times When I power on the camera, the shutter lens trys to open but it can't. I've purchased a new battery and fully charged it. The camera was purchased in May 2008. I've only used it about a dozen times. The last time was Christmas of 2008. Can you help ? Lens won't retract


... Olympus FE-280 Digital Camera

No Power The G9 camera stopped powering on. Nothing happens when I try to turn it on or preview the images. I have tried several batteries ( all are good and work fine in my XTi ) The contacts look clean and I wiped them anyway, still nothing. Help. I am technically savvy and have no problems with dis-assembly and re-assembly.


Le G9 appareil a cessé de fonctionner. Nothing happens when I try to turn it on or preview the images. Rien ne se passe lorsque j'essaie de l'allumer ou de la prévisualisation des images. ... Canon PowerShot G9 Digital Camera

When I power up my nikon coolpix l3, the screen is pure black. It doesn't help when I push shutter halfway. When I take a pic it's pure black. Sometimes when I power the camera up it works fine but the black screen happens more frequently than not. Batteries are fresh and warm. Playback is fine.


Sounds like your lens cover isn't opening all every time. ... Nikon COOLPIX L3 Digital Camera

My shutter will not open. The power button presses in and nothing happens. I have since got a new battery that was the problem, shutter still will not open. Camera is not operative, please help..........dont want to buy another camera.


Can you get any signs of life? playback pictures etc? Try pressing the playback button instead of the power button. If camera display works then press the picture button and see if the camera will switch over and the lens extends. Also check if the t ... Fuji J150w Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3260 seconds