Having problems with your HP Photosmart M407 Digital Camera ?

Wont turn off. When I pull batteries to power down the lense does not retract.


Answers :

Fixing a Lens Error on a Digital Camera
\012
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for HP Photosmart M407 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Power issues. Just recently I've encountered a problem with my camera. After plugging it into my computer (And not noticing the power surge notification on the desktop while doing so). It locked up and powered itself off. I tried turning it back on, and it turned on for a split second then shut off without retracting the lense. I switched batteries and it retracted the lense, but I tried powering it on and the lense only came halfway out and it powered off. I've tried 4 fresh sets of batteries a


You sdaid power surge on the laptop.\015\012Thus suggests that this may have affected the camrera.\015\012I would think a 'repair' if such is possible will be near the cost of replacement.\015\012Only Olympus can advise ... Olympus FE-115 Digital Camera

Wont turn off. When I pull batteries to power down the lense does not retract.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... HP Photosmart M407 Digital Camera

Lens stuck The lense is stuck in the out position. Batteries were replaced but the camera says on the screen "Access", "Turn the power on / off again", and still does not retract the lense.


Solution:The Lense is obviously jammed some how.Suggestion:Send the product back to the manufacturer and see if they can repair the product or send you a new one. ... Sony Cyber-Shot DSC-W1 Digital Camera

Power doesn't work properly. When I turn off camera with power button, lense stays out. When I turn on, the lense goes in then back out again, but after a few seconds, I get the message: "Please turn camera off then on again." If I don't do anything, the camera will turn off by itself, and the lense will go in. Battery is fully charged, and nothing dramatic happened to start this problem...


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Panasonic Lumix DMC-FX8 Digital Camera

I swapped out batteries with the power still on. Now it won't operate properly. The power won't turn off unless I remove the battery and then the lens won't retract. I turn it back on and the lens retracts and then reopens but I can't take pictures.


Hello, You may need to remove battery for 24 hours then reload camera firmware from Kodak website as per user manual directions,the directions are also on the website.Hope this solves your problem,if not,it will be a trip to the repair shop.Regar ... Kodak EasyShare DX6490 Digital Camera

Camera was on, working fine. When powering off, telescoping lens did not retract so lens remained extended just a bit with lens cover open. Waited a few minutes, turned it back on and I get the "access" display message then the beeps and (turn power off and back on) message. While off, I have removed the battery, replacing it with a fully charged spare and it still does this. The lens tries to telescope a little bit and retracts a touch, but I can't get the camera out of this mode. Can it be res


Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Sony Cyber-shot DSC-W55 Digital Camera

Canon Powershot SD450 E18 problem: The camera lense would not open and reported error code E18 on power-up and then would shut down. I followed a procedure on the web for this issue and got the camera lens to open and it was working (able to take pictures for about a minute). When I powered down, the lense did not completely retract. I tried re-powering on but nothing happened. The camera is not getting any power. I figured the battery died so I re-charged it. I put the fully charged batt


... Canon Digital Cameras

Same Problem When I hit the power button, it flashes, the HP logo comes up on the screen the lense retracts and comes back out and the power goes off. That's all it will do. Other times when I turn it on, a little yellow light on the bottom left side in the back flashes once after the blue power light flashes three times and then turns back off. Arggggghhh!


Use never used batries i have the camra it work s better with new batries ... HP Photosmart M525 Digital Camera

Lens stuck I had been turning my Sony Cyber-shot DSC W50 off and on a few times, when suddenly as I went to turn it off, the lens got stuck and couldn't retract--just made this horrible mechanical noise like it was trying to do so but something was awry. Then this message comes up on the screen "Turn the power off and on again." I do as asked. Nothing. I take the (fully charged) battery out and see if that does the trick. Nope. No matter what I do, the lens will not retract, regardless of how ma


I have a Sony Cyber-shot DSC-W30 and my lens was stuck after a trip to the beach. As you turn on the camera, gently tap the bottom of the camera on a hard surface (i.e. a hard cover book). You could also use an air-duster spray to blow out any grai ... Sony Cyber-shot DSC-W50 Digital Camera

Camera powered on, lenses extended, then got an E18 error message. Won't take pics, lenses won't retract. Tried charging battery, no difference. Powers up, powers off, that's it.


Canon E18 error happens when the lens gets stuck while trying to extend. There is a step-by-step tutorial (with pictures) for fixing this yourself on this ... Canon PowerShot S410 / IXUS 430 Digital Camera

HELP!! I am having a real Kodak moment. I have a Kodak M883, The wall charger says the battery is full but when you put the battery in the camera the camera turns on, the lense extends, battery reads empty, the lense retracts and the camera shuts down.


Hello : \015\012 \015\012It seems that the battery is dead or the battery base is rusty or there's isolation stuff on it . Try to clean the base first . If that didn't help , then I recommend you to replace the ... Kodak EasyShare M883 Digital Camera

Hi. I have a finepix jx250 digital camera. The camera lense keeps going in and out and there is a messege that says to turn the camera off and on again.. I did that but it still did the same thing. I tried pressing the shutter and power button at the same time. I tried pressing the power button and the menu/OK button at the same time. I tried taking the battery out and putting it back in. I tried taking the battery and the memory card out putting the battery back in and leaving the memory card o


Hi,Checkout this tip about digital camera error messagesLens Errorfix for Digital Cameraheatman101 ... FUJIFILM FinePix JX250 Digital Camera

The camera turns on, but the lense makes a clicking noise and then the screen says Turn the power off and on again. I have tried this, and also tried resetting it but nothing works. The lense also does not retract, even when the camera is off.


Your problem may be due to weak/worn out batteries or corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: rem ... Sony Cyber-Shot DSC-P200 Digital Camera

Olympus tough TG-820 will not turn off. Clicks to power up and then turns off and on over and over. Cannot get it to stop unless I pull battery. But it starts back up when I put battery back in


... Olympus Digital Cameras

Ive had my Camara a while and I really wanted too take pictures today. But when i turned it on it said access, went in and out 3 times, and then said 'turn power off' Ive tried loads of things, such as; Giving it a little tap and pushing the lense, pulling the lense. and i i've even tried initalizing it so many time and that doesnt even work. Soo what am i suppost too do?


Change the batteries....make sure the card is sitting in it right...try these ... Digital Cameras

When power is turned on the zoom lense moves in and out on its own for a couple of seconds then stops. Camera remains on (battery is charged) The message changes from "access" to "turn the power off and on again." When that is done the same process happens again. Photos can be retrieved that are in the memory to view but the problem is getting to the starting screen in order to take a picture. What's up with that? Hope you can help!


This could be dust or lint or sand that has worked it's way into the lens assembly, and is keeping the lens from initializing. Often, you can take compressed air and blow it into the front lens assembly, to try to free up the small gears there. H ... Sony Cyber-shot DSC-W55 Digital Camera

I have just downloaded the camera on to iphoto and have cleared the camera memory . I clicked the eject icon on iphoto and once cleared unplugged the USB download cable . I have just pushed the power button to turn the camera on and firstly get the message on the camera screen "Access" then a message comes up saying "turn the power off then on again " When I do this the same process repeats itself . The lenses wont open and protrude out of the camera ready to take photos. The battery has ju


Sounds like you did two things wrong...you deleted/erased/or formatted the camera using the computer. You disconnected the camera without using the "safely remove hardware" function. ... Sony Cyber-shot DSC-W50 Digital Camera

Sony Digital Still Camera DSC-P100/P120 I ran my camera till battery ran dry. Camera lense remained protruded. After recharging, the acess flash came on asking me to awitch off power and restart my camera. This I did but lense will not retract when closing down. The camera charges up ok and I have tried removing battery to solve problem to no avail. Any suggestions. I am considering taking a screwdriver to it to remove back of camera. Please help. Kindes regards John Burleigh, Scotland


HI there,There is definitely some risk here, so take care when conducting the following fixes.\015\012\015\012Repeatedly tap the padded/rubber usb cover on a hard surface with th ... Digital Cameras

My cannon g7 just stopped workng. its like it had a power short or something. all power just shut down. it left the lens out. ive tryed swapping the battery ive checked the battery cover is properly shut. but no lighs will appear and the camera wont do anything and the lense is still out.. should i pull it apart my self and have a look. could it be dust or sand or something stopping a conection?


Common problem. \015\012refer this solution #1\015\012http://www.fixya.com/support/t2238145-canon_powershot_g7_just_wont_turn_no ... Canon PowerShot G7 Digital Camera

Suddenly, after taking some photos the camera will light up to the Fujifilm start window, and no further, then blacks out. It will not shut off with the power button, nor retract and close the lens even when I pull the battery out. I have tried two batteries. When I plugged the camera into the laptop, the lens retracted. Any ideas on what may be the issue?


The main board is bad. Was it recently dropped? If so, then the board might have been damaged - it's not worth fixing. When a camera is dropped it's like a car getting into a major collision - you'll have other problems later. As long as the memory c ... Fuji FinePix J10 Digital Camera

The lens has opened when I turned on the power but will neither retract if the power is turned off nor can I take a picture. I have changed the battery but it still does not work. Can it be repaired please


Ensure first that there are fresh new batteries inside, drained batteries can cause the same problem.That happens because the lens mechanism get stuck , either because of dust inside, of because a part is bent or not well placed. ... Digital Cameras

Fugifilm FINEPIX A205S When I switch on the power the zoom lense comes out but the screen is blank and when I try to turn the power off nothing happens and the lense doesnot retract.


Has t\\it got jammed.. ... Digital Cameras

Dropped approx. 3 feet onto carpet. Camera was on and lense extended. It would power up, get into capture mode and flash "sensitivity" and a green light LLC. After about 50 on & Off's the camera turns on but doesn't come out of playback. I have to open the battery compartment and close it then when I turn it on it will go into capture mode. When I take a picture it is washed out with lots of little vertical lines. Did the lense get knocked out of whack? Can I reset this? Any help will be ap


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Pentax Optio M20 Digital Camera

Battery Problem My 18-month-old Canon A70 is giving "change the battery pack" message and turning off constantly, even though I have fully charged three different sets of new rechargeable batteries and rotate them as soon as the message comes on. Sometimes with this message I pull out one charged set and put the same back in, and it works fine for quite awhile, then repeats later. I imagine this is a problem in the camera battery power circuit or something. Never happens when plugged into the co


I figured out the problem. My AA battery recharger was not making good contact, so although it said the batteries were recharged, this was not the case. After fixing this and getting full recharges, the problem went away. ... Canon PowerShot A70 Digital Camera

Hello, I have a Kodak easy share z1275 and has worked well for me for almost 3 years. Used it last week with no problems, has never given me any problems. Suddenly on Saturday, I turn it on to take a picture, lens begins to retract and the camera shuts off, it appears that there is a power supply probelm. I changed batteries, even though the ones I had in it were recently installed, but went ahead and put in new ones, and it will not power on. The blue power indicator light begins to come on


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Kodak EasyShare Z1275 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2675 seconds