Having problems with your HP Photosmart M525 Digital Camera ?


Answers :

Fixing a Lens Error on a Digital Camera


This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Repair Help & Product Troubleshooting for HP Photosmart M525 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... HP Photosmart M525 Digital Camera

Lens Stuck My Lens is stuck on my Coolpix S200 and I'm getting the Lens Error message. I tried to push it back in like I read on here and it went partly in and now its completely jammed. I've only had my camera for about 4 months. Please help!! I'm hoping to fix it myself. i dropped my camera and now the lens wont come out. Everytime i turn on the camera it tells me to turn it off then on again. I've done it multiple times and it doesnt work. I tryed to push the lens in and out but it doesnt ma

YOU CANNOT REPAIR THIS SOPHISTICATED CAMERA YOURSELF!!\015\012I guess pushing the lens inside may have made the problem worse.\015\012I follow a rule- if you drop an electronic equipment and a problem occurs- it usually takes a profession ... Sony Cyber-shot DSC-S700 Digital Camera

Memory card errors. I turn it on and get message MEMORY CARD ERROR PLEASE CHECK CARD. Occurs on different cards. Sometimes I can clean the contacts on the card and it will work. Sometimes, I can take pictures but if I remove the card it cannot be read if install it back or by a computer or printer. I use the camera as publicity in trade shows taking then printing pictures, so the cards are removed and inserted constantly. I have reformatted the card in the camera, still fails.

Hi wait a moment pls your request is been proceeding.. ... Panasonic Lumix DMC-FZ18 Digital Camera

My Kodak easyshare m380 isn't working properly...I turn it on, and it will turn on, but the moment the lens pops out, it pops right back in and the camera shuts off....I've tried replacing the battery but it doesn't help....and I don't have a warranty on it anymore...is there anything I can do to fix it? Or could I get someone else to fix it for a reasonable price...? Please help!!

Your camera has a lens error. This\015\012 is such a common fault that I hope you don't mind me pasting my stock \015\012generic answer ... Kodak EasyShare M380 Digital Camera

My camera after being charged my camera turns right back off. put new battery in and did not help. camera was working perfectly after last use but did not charge right away as I usually do. set for a few day. my sis gave me this camera and I love it please help me fix it. my e. mail is johanna wherry @yahoo.com

... Kodak EasyShare One Digital Camera

My casio exilim ex-z2 flash is not working... when you turn on the flash sometimes it flash but only 2shots, most of the time the flash is not working ang the picture was dark.. what should i do? can you help me please... my mother brought me this camera from france and im in the philippines..i cant go back this unit!

... Casio Exilim EX-Z29 Digital Camera

I have a Sony DSC W120 Digital Camera. I've owned it since Mid-summer and have just recently been experiencing this problem.. When I turn the camera on, it will sometimes say "please re-insert the memory stick".. I will take it out and put it back in, then it will work fine. It does this periodically. What's going on here?

Hey there. sometimes dust and other particles stick the metal contacts that the memory cards use, either on the camera itself or on the memory card. you can try to clean the memory card contacts by using a damp q-tip or something of that nature. be s ... Digital Cameras

My camera won't turn on but it'll let me view all my pictures just fine. I think their might be a problem with the shutter because it sticks out a bit. When I try to turn my camera on it'll show the FujiFilm Welcome Screen and then just go to a black screen. If there is anyone who knows how to fix this without taking it to get fixed professionally please tell me, i would be very grateful of that! If not, and you know where they can fix it (other then sending it back to the company) please inform

This is a very common problem. It may need firmware upgraded. The manufacture will do it for $50 or you may be able to find a software update on the web. ... Canon PowerShot A620 Digital Camera

My samsung s1070 will not turn on. it was working yesterday and i was able to take pictures with it. now when i turn on the power button the camera beeps three times but nothing is visisble on the lcd display. also the lense is fully out even though the camera will not turn on. why is this happening and can you please advise me how i can turn the camera back on so that the display works aswell?

OK you are probably going to think I am loony giving you this advise But No I am completely sane!Get a can of compressed air OR acces to a compressor at your local garage Get them to fit the triggered air blower tool to it.Blo ... Samsung S1070 Digital Camera

My Lumix DMC-FX8 shows me the message turn off then turn back on again for some reason my flash stopped working completly. and randomly it tell me to "please turn off, then turn back on" i tried everything. HELP I'm having a similar problem with my Lumix DMC-FX01. Movie taking won't work either. I don't if the camera might have gotten some moisture in it or what. Any suggestions?

I had this problem on the weekend! I fixed it with a more archaic method. When it says turn the camera off and then on again, the lens is stuck out. It only goes back in when I turned the camera off and then on for a brief second, and then pops out a ... Panasonic Lumix DMC-FX01 Digital Camera

Battery failure I charge my Pentax Optio S5z battery on the charger then put it in the camera when it is fully charged (green light comes on on the charger) but the camera won't work ie. battery is dead, as i put it back in the charger and the light comes up red like it is flat again. Sometimes I just leave it in the camera and it seems to work after a few days, then may last for a day or sometimes for ages. I'm guessing the battery is stuffed but I want to check before I buy a new one. Please

The only solution for that is to buy a new battery. I had the same problem with my canon 900Ti (NB5 battery), died after less than a year. It probably exceeded it's battery cycle life... have a nice day! ... Pentax Optio S5z Digital Camera

My camera is less than a year old but has recently been giving problems with the battery connection - I believe. The battery shows full and the camera works perfectly, then with no indication why the camera will not turn on. When left and then turned on later it sometimes works again, without the battery being charged in the meantime and with it again showing full. As I am going on holiday in 2 weeks I have not time to send it back to cannon under guarantee. Can you suggest anything I can check?

Check if your memory slot cover is properly closed... this doesn't turn on the camera....I had tough times, later found the cause... ... Canon EOS Digital Rebel XS / 1000D IS Digital Camera

My d200 is picky about when auto focus works. It won't work for the shot I want, but if I turn the camera 8 degrees and try at that angle, it works fine. Sometimes turning the camera to manual, then off, then on, then back to auto focus does the trick, but not always. What is going on?

The focus ring inside the camera is a free-spinning lens that is controlled by electromagnets, with feedback from the microprocessor and sensor. When some dust, lint, sand, or dirt works it's way into the lens assembly, the ring can hang up, which ... Nikon D200 Body Only Digital Camera

I have a panasonic lumix DMC-TZ3 camera and it's not working. When I turn it on, the lenses comes out/goes in like 3 times but it won't focus and stay open. I can't take a picture. A message says to turn it off and turn it back on again, but it doesn't work. I can view my album in the the camera....please help!

Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic Lumix DMC-TZ3 Digital Camera

Power doesn't work properly. When I turn off camera with power button, lense stays out. When I turn on, the lense goes in then back out again, but after a few seconds, I get the message: "Please turn camera off then on again." If I don't do anything, the camera will turn off by itself, and the lense will go in. Battery is fully charged, and nothing dramatic happened to start this problem...

HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Panasonic Lumix DMC-FX8 Digital Camera

I cant turn on my camera,i bought new batteries but same problem,but when camera connected iwht computer it works fine,but when not connected it not working,screen sometimes white,sometimes black :( PLease help me

Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... HP Photosmart M22 Digital Camera

My sony cyber-shot 7.2 mega pixels digital camera is NOT working. When i turn it on, it says acess, then the lense comes out and goes back in over and over. After doning that about four times it says "Please turn camera off and then back on again" However when i do this, it just repeats itself. Any idea of what i should do?

... Sony Cyber-Shot DSC-S40 Digital Camera

Dsc-w90 I just bought this camera a few weeks ago. Within the first 200 pictures that I took it started giving me this error when I turn it on that says "Turn off camera and turn back on to use." Sometimes I have to do it 4 or 5 times before it will work again. Has anyone else had this problem? Is the camera just defective?

You will need to pack this camera as if you were packing a pack of ciggs or a deck of cards. this will cause it to resync with the lens. ... Sony Cyber-shot DSC-W90 Digital Camera

Help!!! i dropped my Nikong Coolpix L11 camera on the pavement. The lens got dented in, so naturally i popped it back to its normal place i turned it on and it worked for about 30 seconds and then popped but with the image that said "Lens Error". So i turned it off then turned it back on and it did the same thing. It did that for about 10 minutes and now as soon as i turned it on it says "Lens Error". I cant figure out how to fix it, i've tried slightly tapping it against my desk, i've tried hol

Hellothere are tiny plastic gears inside and may have chipped or a small piece of sand got in causing the lens to jamb. "very fragile"one solution is to ask a camera repair shop how much a lens mechanism would be to replace. ( ... Nikon Coolpix L11 Digital Camera

Help!! My Sony DSC-W100 isn't working. I've been sifting through the message boards and none of the solutions were working for me. Some of my friends were fiddling with my camera and the camera got left with the lens out and no battery left. So I charged the battery and put the battery back in but now the lens is expanding and retracting four times while the camera reads "access" and then "turn the camera off and then on." I've been doing this repeatedly with no avail! Is there anyway to fix it

The only thing that can be done but may not fix it is to push reset switch under battery compartment door (pinhole)..also make sure you do use fresh batteries.Use good batties not cheap batteries because these camera require good current to drive ..i ... Sony Cyber-shot DSC-W100 Digital Camera

Dropped camera I dropped my camera very lightly now the lens are stuck. Is there any way to fix this without going to a repair? I just got this one week ago and the drop was so light. THe screen works it says Access though and then it says turn the camera on  & off i did this but it still doesn't help. But the menu screen & etc works. Please help, thanks!

Check this out\015\012\015\012http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Sony Cyber-shot DSC-W55 Digital Camera

My camera will turn on and sometime it doesn't even when i put new batteries in it and i have cleaned the the battery parts and battery for good connection. I have to take the batteries out and put 'em in and it only sometime comes on. it still didn't work but even if I put new batteries in it doesn't work just takine the batteries out and put 'em back in only makes it work randomly and the battery on the negative side seems lower than the other like they're unleveled. there wasnt any corrosio

If I understood correctly ..it a 2 batteries camera ...and the reason they are not leveled is cause at one point they was wrongly inserted and forced the cover door to close...and the contact blades inside just bended in on the side of the negative . ... Kodak EasyShare C713 Digital Camera

I have a Cyber-Shot DSC-W120. When I go to turn it on, the screen stays black and the lens just goes in and out, then I get an error message to turn off camera and then turn it back on. This is a new camera and I would like to get it fixed. What can I do to make it work?

Try Initializing the Camera. To initialize the Camera. First, press the Home button to display the Home menu. Then, select the Settings option in the Home menu. Then, select the Main Settings1 under the Settings option and set the Initialize under th ... Sony Cyber-shot® DSC-W120 Digital Camera

I just got my camera back from Canon but it still isn't working right! I took it in because when I turned it on it said NO CF CARD. They fixed the metal prongs. Now, it still doesn't work to store or view photos on the camera without a cf card. I inserted my old CF (undamaged card) and formatted it and now it seems to take photos BUT nothing shows on my camera viewfinder when I go to take the photos. It shows I have over 3000 photos on my card but they will not display. Help!

... Canon Rebel XT / EOS 350D Digital Camera

My camera worked very recently, as I took pictures on a camping trip. However, a few days later after getting back, I've found that it refuses to turn on. If I turn it to either Video or Photo, the light turns green, but then immediately flashes red several times and shuts off. I've tried different batteries, with and without several SD cards, and nothing works... How do I fix it?

Here are the steps for the no power problem: 1. Make sure you will install a new or fully charged battery/batteries into your camera. Please use lithium batteries Ni-Mh or rechargeable Batteries (2000 M.Amp or higher). 2. Clean the battery contacts. ... Kodak EasyShare CX6200 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4566 seconds