Having problems with your Kodak EasyShare CX7430 & EasyShare Printer Dock (Pack) Digital Camera ?

Sand in lens and shutter preventing it from

\015 Sand in lens and shutter of my Kodak Easyshare cx7430 is preventing it from functioning - is there a way to force the lens to deploy in order to clean it?\015

Answers :

Fixing a Lens Error on a Digital Camera
\012
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Kodak EasyShare CX7430 & EasyShare Printer Dock (Pack) Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sand in lens and shutter preventing it from


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Kodak EasyShare CX7430 & EasyShare Printer Dock (Pack) Digital Camera

Digital camera got dropped into the sand, and some sand worked its way into the lens and focusing system, and now the camera cannot zoom or focus, but still turns on and takes pictures i have a lumix dmc fx12, and it got dropped into the sand at the beach. the shutter wont close properly, there's sand in the lens, and it won't zoom. Please help!! i don't know how to fix it!!


THIS SOUNDS TERMINAL, BUT YOU MIGHT TRY USING CANNED AIR LIKE YOU USE TO BLOW DUST OUT OF YOUR COMPUTER, AND SEE IF IT HELPS ANY. MOST OF THESE CAMERAS ARE MADE WITH THE IDEA THAT THEY WILL NEVER BE TAKEN APART OR OPENED FOR CLEANING ETC. SO, THAT IS ... Digital Cameras

Coolpix L18: The LCD screen is broken; just displays a large black "blob" on a white background. Would this prevent all other camera operations? When the camera is turned on, the green power light flashes, but nothing else seems to work. Camera will "beep" when shutter button is pressed, but lens never opens. Is this a LCD issue, or are there other problems as well?


... Nikon COOLPIX L18 Digital Camera

Apparently sand in the lens mechanism is preventing its proper operation. How do I fix that?


Try blowing it off with a can of compressed air. ... Casio Exilim EX-S600 Digital Camera

I dropped my camera in the sand and the shutter will not open and the lens will not open out. keeps telling me to turn camera on and off this doesnot work


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Sony Cyber-Shot DSC-S40 Digital Camera

My d5000 fell on the floor and the filter glass of the lens broke. i tried taking pictures to see if it's still working but the view from the viewfinder is darker than usual and it would not take pics even if i press the shutter release button. should broken filter glass prevent taking pictures or does this mean there is another damage to the camera apart from the broken filter glass?


The filter should have nothing to do with the images recorded on camera (I assume it's an UV- or skylight filter).I'd say there's some more serious damage to your camera and you should take it to an authorized dealer repair shop. ... Nikon D5000 Digital Camera

Shutter issue When I turn the cam on the lens comes out, but the shutter over the lens only opens part way. When I turn the can off, the lens retracts and the shutter opens all the way and stays open instead of closing as it should. Not sure how it happened.


I experienced the same problem and took the camera in for repair - I was told the problem was with the motor on the zoom drive which had to be replaced. The shutter cover has worked fine ever since. Repair cost was about $150 ... Pentax Optio 50 Digital Camera

Lens error When I try to zoom the lens, it comes up with a lens error. We just got back from a trip to the beach, where my daughter accidentally kicked up sand while she was running toward me and I had the camera ready to take her picture. When I power up the camera I can hear a gritty sound when the lens extends. I've cleaned up the rest of the camera, but don't know how to get the sand out of the lens housing.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will hav ... Canon PowerShot S3 IS Digital Camera

SAND IN LENS


... Digital Cameras

Ixus 70 dropped in sand, lens error & won't close


Hi jasperke,try the following:make sure your Canon has fresh batteries and it is in recording mode.1) Remove the batteries from the camera, wait for a couple of minutes,then put them back in and turn the ca ... Canon IXUS V2 Digital Camera

The Beach When i was at the beach, i dropped my camera in the sand (the lens facing down). i tried blowing the sand out, picking the sand out with a needle, and nothing worked. the camera still work. but when i turn my camera off, the door that covers the lens, won't shut.What do i do?


You may want to call Olympus Customer Service and discuss their repair process and procedures for sending the camera in to have the lens assembly cleaned. Their telephone number is 800-622-6372 option 2 and then option 3 ... Olympus FE-190 Digital Camera

My casio exilim cant open the lens anymore.I think it was stuck up because of the sand.My cousin left it on the sand when were having our swimming last April 2010.And the big problem is that she left my digicam wid the lens opened and facing the sand.And while on the sand when she knew that it was still on she off it immediately.After that incident,the lens cant open anymore.Can it still be repair?....i dont know where to bring it,i dont have any idea where is the casio service center here but i


Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuu ... Casio Exilim Zoom EX-Z250 Digital Camera

Canon SD4000 camera, when hitting the power button, the screen remains black screen, the green light blinks twice, lens zooms out, shutter opens. Screen remains black, and I do not seem to have any control at all; pressing the zoom button doesn't move lens, no notable reaction to anything. Hit the power button again, the lens zooms back into it's original position, shutter closes (occasionally does not shut completely), green light blinks twice, screen remains black. Tried turning on w/o SD card


... Canon SD4000 IS IXUS 300 HS Digital Camera

Lens Error My daughter and I just got back from a trip to St Croix. We stayed at a resort on the beach and also went snorkeling. The camera was exposed to sand and water. While snorkeling we had the camera in a zip-loc bag so I do not believe it got water in it but I know that while on the beach it may have gotten sand on it. Now the lens won't retract and we are getting a "lens error 12". Any suggestions? Thanks


Hard choices here my friend. Sand in the lens system is bad news.Jams up the close fitting bits. You basically have two choices. Get the camera repaired or throw it away and buy a new one. Cost of repair will likely exceed the v ... Kodak EasyShare C330 Digital Camera

Shutter when i turn on the camera the lens comes out and the shutter closes, when i shut it off the lens gose in part way and the shutter stays open.


Try this: 1.turn on yer unit2.press the menu button(if it gives you the "turn power off and on again message just switch to play mode or preview mode and access the menu from there.)3.select setup(the option with the toolbox i ... Sony Cyber-Shot DSC-S500 Digital Camera

Lens adaptor I purchased a Phoenix 1300mm lens for my minolta cameras, maxxum 7d digital and analogue. The lens adaptor that was supplied with the lens has no cantacts and when attached to the body and the shutter release pressed, the camera indicates that there is no lens attached. The company that I purchased the lens from in Queensland Australia, and Phoenix themselves no longer seem to be in business so Ihave no results from them. The Phoenix lens is a screw mount looks like early Pentax but


The good news is that it is possible to get the camera to operate with the lens & adapter :-)The bad news is that you'll only be able to use it in manual mode :-(To get the camera(s) to actually fire, you will need to chan ... Konica Minolta Maxxum 7D / Dynax 7D Digital Camera

Lens Error I fell while holding my camera. The lens was open at the time and when I got up I turned the camera off. I then turned it back on to check it and the lens opened and immediately closed with the "lens error" on the screen. I can turn it off and on and the lens will always open but closes as soon as it has opened with the lens error on the screen. The shutter opens but closes also, like the lens. Can this be fixed? It was a gift so I don't have the bill of sale but I still have the orig


This is probably THE most common failure among digital cameras. There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Nikon COOLPIX L4 Digital Camera

Lens shutter the lens shutter does not open automaticly when turning camera on.


This is a problem in the lens mechanic. i guess it has taken some kind of a hit, and something broke up.\015\012anyway, its a very delicate mechanism, i would give it to a repair shop and not mess with it myself. ... Canon PowerShot A520 Digital Camera

Today i went to a beach nad my camera fell in the sand. After taken it out when i switch on, the lens does not move at all. It is stucked because of sand and on the screen it says "lens error, restart the camera". So in order to get it fix, what should i do? for information, i bought it from best buy in houston last thanks giving.


Sorry to hear that shivamfc. You are an unfortunate Canon user with the unlucky results of digital camera + sand = dead.To make the camera to work again, you need to be sure to remove the sand that got inside the lens mechanism, unfortun ... Canon PowerShot SD880 IS Digital Camera

Hi, we dropped the Canon IXY in the sand and the lens now won't retract. We have tried to clean out the sand but the message persists. Is E18 a lens problem or something else?


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that ... Canon IXY 1000 Digital Camera

Lens error i brought my camera to the beach and sand got on the camera. i got a majority of the sand out, but the camera continues to say "lens error". help!!


The very smallest piece of sand will jam any digital camera lens. You should be extremely careful to never allow sand to get anywhere near any digital camera. The gears are very small, thus the smallest piece of debris will do a lot of damage. To rem ... Nikon COOLPIX L3 Digital Camera

Cybershot W150, when I turn it on, the lens extends...the shutter opens...but the LCD screen does not come on. Then the lens starts retracting and extending about 3 times and the camera shuts down. I can view and down load the photos that were on the camera, but the shutter button does not function.


... Sony Cyber-Shot DSC-P72 Digital Camera

Lens cover i dropped my camera for the first time in the sand. i guess grains of sand got stuck inside and the lens cover will not open fully. i've tried compressed air. any other ideas?


I was lucky to solve my problem with sand-stuck-lenscover with 6 bar compressed air. ... Nikon COOLPIX S9 Digital Camera

Wont turn on, shutter open at all times When I power on the camera, the shutter lens trys to open but it can't. I've purchased a new battery and fully charged it. The camera was purchased in May 2008. I've only used it about a dozen times. The last time was Christmas of 2008. Can you help ? Lens won't retract


... Olympus FE-280 Digital Camera

Sand Hello my name is Vlada, i have lens error on my canon A450 in my lens is sand can you help me


Compresor! ... Digital Cameras
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1150 seconds