Having problems with your Kodak EasyShare V603 Digital Camera ?

My V603 instantly shuts off after I turn it on. The lens expands out then automatically goes in and the camera turns off. I replaced the battery and I can set the date & time & review my favorites but as soon as I try to take a picture - it turns off. Any suggestions?


Answers :

Fixing a Lens Error on a Digital Camera
\015\012
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Kodak EasyShare V603 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My V603 instantly shuts off after I turn it on. The lens expands out then automatically goes in and the camera turns off. I replaced the battery and I can set the date & time & review my favorites but as soon as I try to take a picture - it turns off. Any suggestions?


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Kodak EasyShare V603 Digital Camera

Kodak easyshare z712IS. sounds like a typical problem but...I try to turn it on, lens only comes out a little bit, then it turns off. I replace the batteries and the set time and date comes on...I set time and date camera turns off. I CAN in fact view pictures in the gallery but as far as taking pictures....nothing.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Kodak EasyShare Z712 Digital Camera

Every time I turn my camera off I have to reset the time and date when I turn it back on. When I first got this camera I could set the time and date and it would stay set until I changed the batteries. what is the problem and how do I fix it?


The small internal battery has died.It will need to be replaced at a camera repair center. ... Polaroid A500 Digital Camera

I have to set the date each time I turn on my Nikon S9 camera even when the battery is fully charged I have the Same Problem .. every time i turn ON the Camera .. it ask's me for the Date & Time .. that accoreded after my camera had a bad fall on the ground ?_?


... Canon PowerShot SX100 IS Digital Camera

The date will not stay set. Every time we turn the camera on it opens with the date screen. We set the date and it then goes into shoot mode but the date is not set. All pictures are stamped with the default start date. Tried a new battery already.


To keep the date on, you have to leave the camera off with a charged battery for 24 hous to charge the inner battery that keeps date on. If this doesn´t solve the problem then is because the inner battery won´t charge anymore, but it wil ... Sony Cyber-shot DSC-W120 Digital Camera

My HP photosmart R967 worked great until it said it was out of battery and shutting down. Now I can't get it to charge, and it won't turn on. Strange thing, when it's on its' little dock charger, it turns on to a screen asking you to set the date and time, then won't set it. My husband thinks it needs a new battery ---- help! I need my camera!


... Digital Cameras

Camera is 5 years old, It has been working fine. Batteries had become low and when I put new batteries in the camera switches on. the , the flash open, the viewer window lights up with set time and date option. The program dial shows low battery but I have tried three different sets of batteries. I have left the camera turned on as I write this and after a few minutes the lens does extend but when I tried it again it will no extend immediately as it should.


Make sure the batteries are the correct type and voltage for your camera. Also because of the age you may have corrosion on the battery contacts inside the battery compartment. If this is the case then no matter how many batteries you try they will n ... Digital Cameras

Every time I want to take a picture, I have to set the date or it goes back to 01-01-80. I replaced the (date) battery with CR1220 as instructed and put in the correct date. When I shut it off and turn it back on I have to set the date. HELP!


Ah-h-h, January 1, 1980....I remember that day. Whoops, I started to slip away!. Try pressing menu/set twice after you set the date and see if it sticks around this time. ... Canon PowerShot A400 Digital Camera

My canon powershot camera goes to set the date and time every time I turn it on. I set the date and time, take a few pictures, turn off the camera, turn it back on again and it ask for the date and time to be set again. This problem developed after a year and a half of no problems. Is there some way to set the clock where it will continue after it is turned off?


\012\012try these:-\012\012\012connect it to pc and on it\012vaccum the barrel of lens\012changing mem. card and batt. for 2min.\012 ... Canon PowerShot SX10 IS Digital Camera

I just recently bought a kodak zd710. When i received the product, i turned on the camera and i was immediately prompted to set the date and time. Once i finished, the batteries that the camera came with had quit on me. So i went out and bought new batteries, and when i went to turn the camera on again, the LCD screen did not light up. It has yet to come on when i turn the camera on. Is there any kind of troubleshooting i can try?


Battery usually come with very little charge when new.You must first charge the battery before use the camera. ... Kodak EasyShare ZD710 Digital Camera

Date and time setting dont save, I changed the CR 1220 battery. Still doesnt save. Every time I turn on the camera the date / time setup appears.


In another forum I found a solution: \015\012\015\012Remove the watch battery from the cameraCarefully bend the contacts inside the camera toward the opening that the battery fits into. - I used a heavy safety pin to bend the contac ... Canon PowerShot S5 IS Digital Camera

Some sort of problem with internal memory / battery? Each time I turn on the camera now it cannot remember basic settings like date etc and I have to select date and time before I can take a shot... Any ideas?


The internal battery needs replacing this is a circular battery . ... Sony Cyber-Shot DSC-H1 Digital Camera

Ixus 80 IS - Won't save date and time Everytime I turn my camera on it asks me to set the date and time, the manual says it has an inbuilt battery (I don't think it is changeable), is there anything I can do ?


After setting the date and time, press the set/ok/menu (whichever one you press at the end) button twice. ... Canon IXUS 80 IS Digital Camera

Set date and time comes up every time i turn on camera


Try resetting your camera. In picture taking mode press menu. Go to setup, go up to reset, press right arrow, make sure reset is highlighted and press set.Then TAKE OUT MEMORY CARD. Go back into menu, go to setup, go up to format, pres ... Casio EXILIM ZOOM EX-Z60 Digital Camera

Set date and time comes up every time i turn on camera


The date time is controlled by another 'button' type battery in the camera- like a watch battery, there 'go' in time.This is not a 'user' fixable item usually because it mean dismantliing the camera.Sending away will be pricey- well on th ... Sony Cyber-shot DSC-W55 Digital Camera

My koadk turns on to the set date and time screen then turns right off. I have a new newly charged battery.


... Kodak EASYSHARE M340 Digital Camera

Fuji finepix a400 camera. When I power it on I get the 'date/time not set message'. I can set the date / time and all in well until it is turned off overnight. It has new batteries installed and I get this message even with an external power supply attached. This is most annoying.


I would suggest going to the fuji website to download the latest firmware driver and update the firmware on the camera. ... Digital Cameras

The internal lithium battery will not hold a charge and i have to set the date and time every time the camera turns on


Have you tried pressing the set/ok button twice at the end of your entering the date and time? ... Canon Powershot A1000IS 10MP Digital Camera with 4x Optical Image Stabilized Zoom

Every time I turn it on, it wants me to set the date and time... It has never done this before I took the memory card out as well as the battery and put new ones in but it does the same thing please help... Thanks J


Once you set date and time, it wont ask you again. I think you always cancel date and time settings, when it asks. ... Sony Cyber-shot DSC-W70 Digital Camera

Camera keeps loosing the time and date settings. When turning the camera on the lens does not open, then a screen asking to set the date and time settings appears - once date reset the camera works properly. Unfortunately this seems to happen almost everytime the camera is turned off.


The problem is the internal battery that powers the storage of time and date. If the camera is unused for a while, it will discharge. You must put a freshly charge battery into the camera and leave it with the power turned off for 24 hours to charge ... Sony Cyber-shot DSC-W170 Digital Camera

I have just bought the Kodak M381 camera and when I set the date and time and click ok, the time is set but does not display on the LCD screen at any point, so when I review my pictures there is no way of knowing when I took them. You can date the pictures retrospectively but that takes time and will be incredibly tedious and you soon forget. In the manual it says to select the date time stamp but I am unable to find it in my set up menu and I'm beginning to think this camera does not have this


I had the same problem. I think the camera does not have this feature, to bad it was a nice camera ... Digital Cameras

When i turn on the camera, it always asks me to set time and date. If i click on yes, then i have to enter all the details as to the date, time, place. Also, the MP size defaults to 14MP instead of the previous setting, for e.g., if i had previously set it to 5MP, it would go back to 14MP after I turn the camera off and on.


Well, I have the same problem. Just introduce once the date and time. Turn off the camera. then turn the camera on using the button for presentation of pics (right arrow). You will see the last picture taken. Press again and you will be in shoot mode ... Nikon COOLPIX S710 Digital Camera

I have a cannon power shot A580, about one month old and it keeps asking for the date and time everytime i switch it on, even though i have replaced the date battery and the camera batteries, and set the date and time in the menu time and time again!!! HELP


If you've replaced the date battery, then the camera is defective. Being only a month old, first recommend seeing if your retailer will exchange it. If not, Canon will fix for free under warranty. Call 1-800-OK-CANON. ... Digital Cameras

Hello, When I just bought this camera several years ago, I entered the time and date settings and after I've done this it never asked for time/date settings again. But now every time I turn on the power button, I have to set the time an date and press "SET" for OK. I read somewhere on the internet that others have encountered this problem as well. Can this be solved??? Thanks in advance, **** Muilwijk


You may need to take it in to the camera place to get the internal batery for the clock replaced also you may need to up load the driver program for the camera ... Canon PowerShot A520 Digital Camera

The date and time will not stay set. I set the date time . take pictures and when I shut the camera off. the next time I turn it on the date and time is zeros again...


The world of compact digital cameras is fast and furious blink and you'll miss the new model. These pocket point and shooters are cram packed full of features that most people neglect to utilize. So it's uncommon for the problem you describe to occur ... Canon PowerShot A710 IS Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2971 seconds