Having problems with your Konica Minolta DiMAGE G500 Digital Camera ?

Lens is locked half way out and screen displays System Error. Camera is locked in this position.

Answers :

Fixing a Lens Error on a Digital Camera
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Konica Minolta DiMAGE G500 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Lens is locked half way out and screen displays System Error. Camera is locked in this position.

Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Konica Minolta DiMAGE G500 Digital Camera

Accidentally I dropped my Sony DSC S500 camera. Now the shutter is jammed. When i switch on, the lens ejects out and stops half way. While switching off, the lens doesn't come back to normal position, instead it stops in half way ejected position. From the LED display i could see a blurred image. I am able to see all the photos that i have taken so far, but am not able to take any new photos.

HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\012\01 ... Sony Cyber-Shot DSC-S50 Digital Camera

My Pentax Optio M60 lens seems to be frozen half way out of the camera with the lens cover also partially open. When I turn in onn it sounds like the lens is trying to focus then turns intself off. Nothing is written on the screen unless I also press the menu button which displays VER 1.00 before bleeping three times and turning off or the green button which displays VER 0163A SBM -FIRM before beeping 3 times and swithcing off. Nothing else seem to do anything. I havn't dropped it or got the cam

HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will hav ... Pentax Optio M60 Digital Camera

When I turn on my Panasonic DMC-FX55 the lens comes out fine and the screen displays for 2 seconds then goes blank except for the message 'Turn off then on again' - which doesn't work. The only way to get the lens to retract is to select 'Playback' - tun off then on . The playback mode works fine and after 10 econds the lens returns to closed position. Is their a combination of buttons that reset the camera??

... Panasonic Lumix DMC-FX55K Digital Camera

Is there a way to "restart" my Casio Exilim EX-Z700? While I was taking a picture it seemed to freeze while it was trying to display the picture I just took - then, with the lens still popped out the screen stayed blank and it turned off, and now it won't turn on. The lens is still stuck in the "out" position. No buttons work. I tried to put it in the cradle to charge, and tried a different battery as well. Nothing works. Camera is dead!

Normally changing the battery solves this.Make sure you replace it with a good quality new battery and make sure it goes in the right way around as when you get in a flap it often ends up in the wrong way! ... Casio Exilim Zoom EX-Z700 Digital Camera

I have an Olympus u700. It worked ok yesterday, then stopped. I switch on the power and the lens comes out about half way, I get blurry images and then the lens closes again. The screen then displays the following: D: 5f08 5e02 It doesn't allow me to do anything, other than turn it off. Any ideas? Thanks Chris

... Olympus Digital Cameras

Upon turning on my camera the message 'lens error restart camera' appears against black screen. I've turned off the camera and have tried turning on again. Still same message. Prior to the above message, my camera displayed a message 'memory card error card locked' and I was not able to see view my photos. I took out the card to see if it was in a locked position to which it was not. Please help as I have vacation photos on this memory card!

Can't help with the camera- sounds like it has a fault.The photos, however, should be recoverable by putting the memory card into a card reader on a computer. ... Canon PowerShot SD1000 Digital Camera

Have Olympus U700 All Weather camera. When I switch it on the lens comes out fully, retracts, comes out half way and finally retracts again. 'D: 5e02' is displayed on the screen. Any ideas. Thanks, Simon Wright

... Digital Cameras

When I push the power-on button the LCD display briefly flashes on with the "Pentax Optio" screen and then switches off. The lens is stuck half-way open, and the camera will not stay powered up. The battery is fully charged (as well as the backup battery) so that isn't the problem. Is there a "camera reset" procedure for this camera? Other ideas?

Good day,This is a common problem and sometimes can be fixed.Please see details on my tip on how to fix this error here:http://www.fix ... Pentax Optio A10 Digital Camera

LUMIX DMC-FX12. the lens will not move in or out. it is stuck half way and you can hear the motor going. on the screen there is no picture just normal display then it will ask me to turn it off and on again.

This is a problem that needs factory attention. Recommend you remove the batteries, pack it up and send it to Panasonic for repair. It is remotely possible that removing the batteries and reinstalling them will kill the motor (the noise) and let th ... Panasonic Lumix DMC-FX12 Digital Camera

When you press the power on button the camera lens starts to move out stops goes in then out again stops the screen does not illuminate at all.IF you then press the power button the lens tries to retract slightly but then stops and again nothing else happens. battery is fully charged. if you press the replay button screen and camera behaves as normal and you can view the pictures taken lens usually retracts all the way to its docked position again if it was nearly all the way out.

... Sea and Sea UNDERWATER DIGITAL CAMERA DX-1G Scuba Gear Cameras

I have a Canon Powershot S3 IS and I was looking at picture I had taken and the lens was retracted. I switched to the camera mode and the lens started to come out and hit my leg and stopped half way. The lens went dark. I turned it off to retract the lens and then turned it back on. The lens came all the way out but the screen is still black and I could feel the camera and just barely hear it making the noise it makes when the lens is coming out but it was already all the way out. I switche

Format ur memory card ....and replace the cells.....might work...contact the customer care for help ..they mightr be able to fix it ... ... Digital Cameras

Olympus fe-47. When you pushed the on button. The lens suppose to come out all the way and the screen fully come on. The lens came out half way and the screen does't fully on but it says olympus on the sceen.

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Olympus Digital Cameras

My Ricoh Caplio R4 will turn on but the lens stops half way. All data comes up on screen, but you can't clear any of it. Then after about 10-30secs, the camera turns itself off and the lens is stuck half way out. Battery is fully charged, was working properly, then just stopped. What could be the problem?

Hello Mar LizThis is a fairly common error with most digital camera's .This either means that something is jamming the lens , or that the\015\012lens sensor is faulty. Given that the lens is stuck halfway , we can rule out a sensor proble ... Digital Cameras

On my Fuji s2000hd I have a zoom error, the screen is black and I can't take pictures. The lens will not zoom out. I believe that my husband put the lens cap back on before the lens had gone all the way in when he turned it off but I am not positive that is the problem. The lens seem centered and there doesn't appear to be anything blocking it from coming out. Is there a way to fix this?

HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a p ... Fuji FinePix S2000hd Digital Camera

LENS PROBLEM Lens keeps zooming in and out when I turn it on. After 4 times, the lens goes back in and it says on the screen, "Turn the power off and on again". Then it does the same thing when I turn it off and back on. Also, the shutter is not closing however it's also not all the way open. Almost half way but more open than closed. Please help!!!

The slightly open shutter is the reason for this problem. Thank God you mentioned it. \015\012Solution: Try with your fingers to shift the shutter “blades” back and forth to see if they move freely. If they do no move freely it maen ... Sony Cybershot DSCW80 7.2MP Digital Camera with 3x Optical Zoom and Super Steady Shot

I have a canon power shot A530. I dropped it on the floor with the lens open.....now the lens is half way out and it wont go out all the way or close all the way. when i turn on the power it comes on then cuts off with out displaying a picture in the veiwer on the back of the camera. I am sure i need to send it in for repair, if not tell me how to fix it, if not tell me where i can take to repair it


My Canon PowerShot SD850 IS has a lens that is stuck in the extended position. I get a screen that says lens error, restart camera, but when I try to connect to the software, I get a screen on the computer telling me the computer cannot detect the camera. Battery is freshly charged, and I get the little yellow bird picture on the camera when I turn it on. It beeps about 4 times, and then turns off. Is there a safe way to get the lens to retract?

Don't play around with that lens, you can do more damage to the camera and focus with some of the stuff people tell you to try. Your camera just needs to be serviced and you'll be working great again. The shop that specializes in service for the powe ... Canon PowerShot SD850 IS Digital Camera

Nikon Coolpix P60 - Screen shows "Lens Error" Screen will not display any images / digital viewfinder will not display any images. Brand new camera, has never been dropped or damaged in any way. Fresh batteries, so it's not a battery issue either.

Same extact problem. anyone had luck getting theirs repaired and if you've taken it in how much did it cost? ... Digital Cameras

The screen on my camera says 'Memory Card Locked'. The solution is to take out the memory card and flick the switch on the side. But I can't take the memory card out- it appears to be stuck. At the same time as the screen starting to say 'Memory Card Locked' the memory card only comes out half way so I can't flick the switch. How do I solve this problem??

... Panasonic Lumix DMC-ZS3 Digital Camera

When I tried to turn on my Canon Powershot (SD880 IS) this evening the lens extended only about half way and the screen remained blank. When I tried to turn it off the lens did not retract fully, and the screen is still blank. I have tried removing and recharging the battery, but it makes no difference. Any suggestions are welcome.

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Canon Digital Cameras

When I turn on my camera, half the display screen is white with a distortion that looks like a crack down the middle. When I switch over to take pictures/view pictures through the lens, everything looks fine. It seems to be just an issue with the display screen.

Did you ever solve this problem? i have it too...Thanks ... Nikon COOLPIX P60 Digital Camera

I have a Nikon D100 with a Nikon AF Nikkor 24-85mm 1:2.8-4 D lens or a Nikon AF-S Nikkor ED 7-300mm 1:4-5.6G VR lens. I'm on vacation in Hawaii and am troubled by an error that appeared today. The "number" displayed on the operating "screen" which normally shows the number of pictures which will fit in the memory available is jumbled and/or semi-illegible. The best way I can describe the number is as follows: If the number were "365" it appears as follows: 3 displays only the top and

You can try and reboot the camera, if this doesn't work then consult the repair shops and see if your display can be replaced for a low cost. For warrenty ifo con tact Nikon at their customer service center at ... Nikon Digital Cameras

Got Camera from Amazon more than a month ago. I believe the focus is acting up. I turn it on/off, or focus it pushing the button half way and it makes this disturbing sound as if a DVC tape is struggling to rewind. Screen & Shots are blurry. I zoom in half way, it's almost clear but not quite. Its not saying Lens Error (yet)

Definitely sounds like you have a problem. You should try and see if it can be repaired under warranty. ... Canon PowerShot SD1100 IS Digital Camera

Lens problem Hi. I have an Olympus FE-190 digital camera. not sure what happened, but now there is a problem with the lens. when i turn on the camera, the lens extends, retracts, several times (trying to find "home" I think). Image on the display screen is blurry. it WILL take a very blurry picture. there is a faint 'ratcheting" sound when the lens is fully extended. is there a way to 're-set" or calibrate the lens extension setting or focus? thanks very much for your assistance.

Take it to Best Buy for repair. ... Olympus FE-190 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3992 seconds