Having problems with your Konica Minolta DiMAGE G600 Digital Camera ?

How to fix a camera lens tha its stock. the lens doesnt cloe and it has an error system s0042


Answers :

Fixing a Lens Error on a Digital Camera
\015\012
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Konica Minolta DiMAGE G600 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to fix a camera lens tha its stock. the lens doesnt cloe and it has an error system s0042


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Konica Minolta DiMAGE G600 Digital Camera

My camera lens wont close and says system error s0042 konica revio kd-310z


\012\012try these:-\012\012connect it to pc and on it\012vaccum the barrel of lens\012changing mem. card and batt. for 2min.\012 ... Konica Revio KD-310Z Digital Camera

My husband had a fall today and broke his foot and he had the camera in his hand. It now shows system error S0042 and the lens will not close. Can you help? Many thanks Angela


Okay, the same happened to my camera. The lens stayed open and showed system error on a blue screen when I tried to close it. I checked if this had happened to others and found that it had, and took note of their comments.\015\012\015\0 ... Konica Revio KD-400Z Digital Camera

System error turn camera on green light comes on as per normal functions ok to that point then lens retracts like it is switching off green light comes on and flashes with system error.if you hold the camera to your ear when all this is going on you can hear noise from within the camera before it starts to retract and green light starts to flash with system error on screen.this happens on all functions.you can still look at pictures already taken this funtion works ok.just can,t take photos any


Hi\015\012the problem that causing this is:\015\012there is some pressure to the lens\015\012\015\012did it fell?\015\012probebly there is a fault in the lens \015\012\015\012sorry cant help\015\012\015\012good luck ... Panasonic Lumix DMC-LC43 Digital Camera

Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work. hi expert i m suffring in this error on my panasonic DMC-LC33 when i switched on


Try \015\012\015\012Klomtrix trick this worked with my camera\015\012thanks klomtrix ... Panasonic Lumix DMC-LC33 Digital Camera

When turning off the camera, the lens does not retract. I also get an error message "SYSTEM ERROR (ZOOM)" and another one "PLEASE TURN THE CAMERA OFF AND THEN ON". Once the camera is turned on, I can hear the lens mechanism working, but obviously failing.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Panasonic DMC-FX37 Digital Camera

I dropped my camera on the floor while i was taking a picture , the camera shut off , but the lens stayed popped out . i tried to turn the camera on again , but i would only show me the home screen , which says "Kodak Easy Share System , Share" then the camera freexes up , and it say in the top left corner , "lens error : 22" i've tried smacking it against things , i've tried smacking it on my hands , i've tried pulling out the lens , NOTHING WORKS. Please Please Please Please Please Please Plea


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that ... Kodak EasyShare CD33 Digital Camera

Minolta G500 My camera lense wont close says system error S0042. Didnt drop it just open the lense to take a picture and green,red light started to flash on and off and then on the screen it said system error S0042


Your lens mechanism is stuck up! try pulling the lens with slight force, if you are lucky the culprit that is blocking the mechanism will get loose. If you are not lucky theres no way you can remove or fix the problem than sending it to the authorize ... Konica Minolta DiMAGE G500 Digital Camera

Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work.


*&%$@#%^&*&^% !!"It's working!!!!\015\012\015\012Turn your camera on and put it near your ear. Did you hear a softly motorized sound in the lenses area and the green LED is flashing? If you hear this sound do this.\015\012\015\012Do it under your own ... Panasonic Lumix DMC-LC33 Digital Camera

System error My camera comes up with a system error and does not take pictures. The lens does go in and out when top dial turned to scene but stays out when power button turned to off and then displays system error... I have tried removing card and battery ...any ideas apart from trashing it? Tony


Go to your camera settings and reset what you can, especially the date and time. Take the batteries out if they are old and leave them out over night. Then turn it on and see if the message is gone. If not, then you may need to get service for it ... Digital Cameras

Hi! Im Michelle from Dubai UAE, i bought my canon elph series camera last july 09 only and just yesterday after turning on the device the lens was stock up and not turning to its place anymore,.i tried to turn it off and on again but the camera is only blinking and there's a message on the screen says "Lens error, restart camera" ...I would realy appreciate any positive feedback,..Thank you very much for your kind attention Sincerely, Michelle Email:[email protected]


Hello.....\015\012sir it might be a lense problem i guess............the spring with which lense moves may be not proper............. slidin of lense is not aceessble by ur cam...........so better if show it to ur provider.......they replace it ... Canon Elph Jr. APS Point and Shoot Camera

We have a Panasonic DMC ZS3 camera that has been working fine until now. We are on the North West coast of Costa Rica. When you turn the camera on, the lens, which was out when shut off, goes in, then comes back out. The camera screen tries to focus, then goes to a blank screen and says "SYSTEM ERROR (FOCUS). When you shut it off, the lens does not retract.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Panasonic Lumix DMC-ZS3 Digital Camera

Upon trying to turn camera Panasonic DMC-ZS3 on, error message appears: system error (zoom). The lens comes out a bit and then goes back in, shutter closes, then lens comes out a bit again, then goes back in again ... then error message. Can you help? Thanks!


I don't know that I can help you fix it, but I can try.\012Here are my thoughts...\012Check the battery first. If it's like a normal battery, like AA or AAA batteries, replace them and try turning it on.\012\012If it's a flat lithium battery t ... Panasonic Lumix DMC-ZS3 Digital Camera

System error When I turn on my digital camera the lens opens and closes and then the screen appears and says system error and shuts off compleatly what do I do?


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Sanyo Xacti VPCX1200 Digital Camera

After i drop my camera the lens system stucks and i have 'lens error ' message. I try to open the camera but i can't find how . could you help me on that ? Thanks Fabian


Hi,\015\012Usually it's sa ... Kodak Easyshare M753 Digital Camera

Lens stuck I have a panasonic DMC-LC43 camera and the lens is stuck out. When I turn on the camera I hear a clicking like it is trying to fix but then I get a system error message. Any idea?


It sound like a problem with the zooming mechanism (lens would not retract or extended)\015\012Press the power button on and hold it down while extending and twisting the telescopic zoom lens. It might fix your problem.\015\012In any case it could no ... Panasonic Lumix DMC-LC43 Digital Camera

System error when I turn the camera on, it moves the lens and then it appears a message: ! system error; then it shuts off.


Try these procedures. ... Sanyo Xacti S70 Digital Camera

My new panasonic lumixDMC-ZS8 14.1MP Digital camera gives me system error (zoom) when I turn it on.the lens will not open?


The systems control board has detected a fault wth the lens, over time dirt and grime collect in the len causing havoc, the other concern is the gears have jammed or got damaged, either way it is a major dis-assembly and it will be expensive. ... Panasonic Digital Cameras

My panasonic dmc zs5 dont work. When I turn the camera on I get this message, the camera will not work, and the lens does not retract when I turn the camera off. it then says system error focus. What is wrong ? The camera is from August so its not old.


... Panasonic Lumix DMC-FZ28 Digital Camera

My camera felt in the sand, so only tiny particles entered to the eye. The zoom does not work when it is on, there is not a clear image. when I turn on the camera. its lens protection does not opens and a message appears saying that there is a system error (zoom) . What can I do to fix it ands not buy another camera.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Panasonic Lumix DMC-FS6 Digital Camera

Zoom lens system error, lens now will not open at all and this is the message. Initially the lens would come out and then jam when camera switched on


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you wi ... Panasonic Lumix DMC-TZ3 Digital Camera

I too have the same problem with my DMC-FS15:- When I turn the camera on in either record or review mode, I get a system error: zoom message after a few seconds, and the camera is inoperable. Then when I turn the camera off, the lens does not retract. Is there updated software that can be downloaded and installed via the supplied USB cable, or any other fix? Regards Martin J


Well perhaps it is just the battery I wonder if this problem isn't simple a bad battery try a replacement, as sometimes they just go bad, and this is indeed a symptom of a battery not working properly. If you have an original power supply, then try i ... Panasonic Lumix DMC-FZ28 Digital Camera

When I turn the camera on in either record or review mode I get a system error: zoom message after a few seconds and the camera is inoperable. Then when I turn the camera off the lens does not retract.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will have to get it fixed by ... Panasonic Lumix DMC-FZ28 Digital Camera

Lens error my camera keeps saying lens error and then shuts off My Kodak M753 digital camera is telling me "lens error: 1,1,5,1,0,0", how can I fix this? - I have no proof of when I bought it, so a refund is out of the question. my camera was covered by luggage and now when i turn it on, it says lens error I dropped my digital camera just recently back in October and all of a sudden when I turn the camera off the lens is still out when it's suppose to be in... I really don't know how that hap


This is probably THE most common failure among digital cameras. There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Fuji FinePix A345 Digital Camera

Lens error When I turn the camera on it says "Lens error, restart camera," and turns itself off. When I turn it back on, the same problem occurs. The lens covers aren't completely closed, and the entire lens seems to be sticking out a little bit, like it didn't retract all the way. Please help! Thanks. Turn on the camera, camera shows a canon logo, then before turns off it said lens error, restart camera


\015\012\015\012I have a solution posted in doc "nikon s5 s6 lens cover error repair.doc"  uploaded on site http://www.esnips.com/web/papputatiyasStuff&n ... Digital Cameras
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4716 seconds