Having problems with your Nikon Coolpix 3700 Digital Camera ?

Hi...my name is nelson, I have got problems with my CP3700, the lenses are always out when I turn it off does not hide the lenses..


Answers :

Fixing a Lens Error on a Digital Camera
\012


\012

This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
\012

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Repair Help & Product Troubleshooting for Nikon Coolpix 3700 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi...my name is nelson, I have got problems with my CP3700, the lenses are always out when I turn it off does not hide the lenses..


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Nikon Coolpix 3700 Digital Camera

My camera wont turn on! I left it charging for a 2 whole days and nothing wont even connect to my hp. Wont even turn on when plugged in on the wall charger and the camera lense is always down wont come up when turned off.


Repair or sell as parts or repair or as is on a site such as Ebay.When you cannot start the camera, then there is not much else to do.It sounds as if there is something wrong in the circuits or the power end of the unit. In any case not g ... Samsung i85 Digital Camera

Hello there, i have a tm700 from panasonic and it seems like the camcorder has some focus or depth of field issues, it always been working good until last week when i turned it on everything is out of focus, i tried geting focus back with auto focusand tried it with focus ring but it just seems impossible. only things that are focus are the things about an inch from the lense and i can get it focused if i zoom in a little... its odd because nothing really hapenned to the camera that could have


Inside the lens assembly, the focusing ring is controlled by electromagnets with feedback from the microprocessor and CCD sensor. Many things can effect the focusing circuit, but the most likely things would be any dirt, dust, or lint obstructing t ... Digital Cameras

Question Yes the shutter does open, but the lense physically doesn't come out although I hear that it tries. When I turn off the camera the shutter doesn't always shut... How to I re-initiate the camera?? Thank you


First, i suggest you try this. Remove batteries then press and hold power button for 15 seconds. Wait a further 1 minute then reinsert batteries and try again.\015\012If no good, try this. If you can get to the MENU mode (in stored pics), scrol ... Sony Cyber-shot DSC-S600 Digital Camera

Zoom malfunction Hi, My cyber-shot dsc-w120 cant go to shooting mode. it always asks me to turn off and on after some unusual movement of the zoom lense. I can still ***** previously snapped pics when i re-play suggesting that its only the shooting mode that has a problem. pls help!


... Sony Cyber-shot DSC-W120 Digital Camera

My camm! I have an olympus digital camera fe-170. when i turn on my camera, the lense come out and the LCD screen is black, when i try to turn it off, it doesnt turn off, but after like 10 seconds it turns off by itself. but when it turns off the lense dont go back in?! then when i try to turn it on, its the same thing. when i plug it into the computer, the lense go back in, but when i unplug it from the computer and try to turn it back on again...SAME PROBLEM. i did drop it before, but can i do


I think thy will say you, replace lens unit. but lens is very expensive, so we can buy new one camera. I have the same problem, i found focusing lens wheel teeth slipping, no parts available, so i covered a gum coat on the teeth. ... Olympus FE-170 Digital Camera

I have an olympus digital camera fe-170. when i turn on my camera, the lense come out and the LCD screen is black, when i try to turn it off, it doesnt turn off, but after like 10 seconds it turns off by itself. but when it turns off the lense dont go back in?! then when i try to turn it on, its the same thing. when i plug it into the computer, the lense go back in, but when i unplug it from the computer and try to turn it back on again...SAME PROBLEM. i did drop it before, but can i do anything


The lens is bad, needs to be replaced. Maybe purchase camera on ebay with broken LCD but good lens. Replacement can be time extensive. Will need #00 or #000 phillips screwdriver and solder iron. Remove 6 exterior screws+2 inside battery door. Take of ... Olympus FE-170 Digital Camera

Zoom error I turned my F470 camera on and received a "zoom error" bar across the screen. The lense does not move outwards after I turn the power on, nor does the plastic sliding screen close when I turn the camera off. The lense is exposed whether or not the camera is on or off. The lense does not make any sounds when I turn the camera on, but I hear (what I think) are the gears when I turn the camera off. When the camera is on, the screen is working, but the image is blurry. I tried other poste


Hey MBB722,\015\012 What is most likely going on is there is something stuck in the lens obstructing its movement (i.e. sand). I don't know what you have tried and what you have not tried you can try placing the came ... Fuji FinePix F470 Digital Camera

My lense is stuck open despite turning my camera off. On turning my camera on I am told ''turn camera on off then on'' but the lense does not retract. I am able to view all photos on the memory card as well as turn the camera on and off, however at each point when the lense should retract it stays fixed out. Can this be fixed?


This is not a joke........Use a can of compressed air and blow around the lens while it is extended. Take a relatively firm approach with this problem slap the camera into your palm two or three times. Not lens down in this case, bu ... Sony Cyber-shot DSC-W120 Digital Camera

Panasonic DMC-TZ4 When I switch on I get "Turn off camera and turn on again" message but it does not good. When I swtich off I get "workng hard" noises as if there is an effort to retract the lense but it will not retract unless I turn the camera on again. At that point the lense retracts and comes out again at once; more "hard work" noises and a new "turn your camera off" message. The only way to get the lense into the retrated position is to catych it at the right instant and remove the batter


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic DMC-TZ4 Digital Camera

Power doesn't work properly. When I turn off camera with power button, lense stays out. When I turn on, the lense goes in then back out again, but after a few seconds, I get the message: "Please turn camera off then on again." If I don't do anything, the camera will turn off by itself, and the lense will go in. Battery is fully charged, and nothing dramatic happened to start this problem...


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Panasonic Lumix DMC-FX8 Digital Camera

I have a canon powershot s5o, and the other day i turned it on,was going to take a photo and appeared E18. it turned off but the lense of the camera did not go inside the hole and cannot close it.. i try to turn it on and appears the first image,and immediately whites stripes on the blackground. and try again and the same. the lense is stuck there i cannot close the thing that covers the lense


... Canon PowerShot S50 Digital Camera

When turned on lense would only retract partially and then turn off. took it apart. I have it to where the camera will now go on, am able to take a photo (all normal) except I cannot get the lense to "attach" to the camera properly. Cylindrical lense. three screws protruding from it. not sure if the lense mounts on a black ring on the front or under the ring. The "in out" mechanism works but it will not grab the lense (cover?) to move out then retract. Seems to need to attach under the ring but


Good day,This is a common problem and sometimes can be fixed.Please see details on my tip on how to fix this error here:http://www.fixya.com ... HP Photosmart M415 Digital Camera

Broken Lense My VPC-E760 Sanyo camera is a little over 4 mo. old. It was dropped about the 2 mo. i had it. Then lense popped back ito place, but it makes a funny noise when turning on and off. (or going in and out when previewing pics). Last night, it was working fine then turned off, said 'lense error 25' 'lense error 22' and 'lense error 12'. I don't know why! I tried to find out what it meant, but i couldn't SOMEONE HELP!!! lens will not go in. camera reads lens error 12 and 25


\012\012try these:-\012\012\012connect it to pc and on it\012vaccum the barrel of lens\012changing mem. card and batt. for 2min. ... Sanyo VPC-E760 Digital Camera

Lense error Yesterday i took some pictures from my EX-Z75 casio exilim camera. After sometimes it stopped working. When i turn it on it turn off it self just after few seconds and lense just keep remain outside. And when i press trun on/off bunnen twice then the lense goes in side. It can not remain on. Y;day it shoed me lense error on my screen. What shout I do? Its not even compelete a year i bought this camera.


Send it in for repair. their is no easy fix for this sorry. www.digitalcamrepair.com can help. ... Casio Exilim EX-Z750 Digital Camera

Only about 9 months after buying my camera, It wouldn't turn on. I'll plug it in and the light will come on that it's charging, but when I got to turn it on, it turns on for a split second (and the zoom lense comes out) and then it turns itself right back off (and the zoom lense goes in). I thought that it needed a new battery so I bought one and it's still doing the same thing. I emailed Kodak and they said that I should just send it into them for a $60 repair fee...lame. Any suggestions?


If its only been 9 months since you bought it shouldn't it be covered for repair? espically if its a manufactures fault,which it sounds like. ... Kodak EasyShare M863 Digital Camera

I cannot turn the camera on. I guess it was dameged during my holidaying. I recall that, the camera was excidently turned on inside its holder and as the mechanism tried to push the lense out from the body it was blocked by the bag holding the camera. Now, when I try turning the camera on, the lense could not move forward at all. It gives cracking noises and turns itself off. Could this problem be fixed or better to buy a new camera? Arthur


If your camera isn't under warranty, I think that it has no worth to repair it by the after-sales.\015\012But you can try to fix it by your self, anyway there will be no loss for a bad camera.\015\012May be this post will be any helpful: ... Pentax Optio 60 Digital Camera

My computer no longer turns on. the favorites part will turn on and the screen will light up, but with any other mode the camera's lense pops out slightly, the green light on the top blinks once, and it shuts off. i have to turn it on again for the lense to go back in. the model is a kodak easyshare z712 IS. I'm going on vacation tomorrow- please help!


... Kodak Digital Cameras

I turned on my samsung sl202 and the lense come out making a funny noise but the lcd screen doesn't turn on. And then the lense gets stuck out and wont turn back off. But I can still view the pictures.


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Samsung SL202 Digital Camera

I have a canon powershot A470 and it fell in water. after i removed the card and batteries of which still worked and neither were wet, i let the camera dry for a couple of days. it has turned on since and the screen would come on and show me the pics on the card but it kept turning itself off and the zoom lense would go in and out on it's own. now, i can't get the camera to turn on and the zoom lense it stuck. any ideas??? or should i call it a wash. i really love this camera!!! Theresa


I submerged my powershot for a couple of seconds. it did get completely wet. it was acting very strangely: the lcd wasn't working, the little orange light on the front kept flashing, and it took a few tries for the lens to extend.then ... Canon PowerShot A470 Digital Camera

My camera, i think i was turning it off. And i was maybe holding the lense. Then it said lense errror. And now, everytime i try to turn it on, it says lens error restart camera, i try turning it on and of, but it doesnt work. And i need it on to upload photos on the computer.


Reset camera, take out battery, try manual repair ... Canon PowerShot A560 Digital Camera

Power issues. Just recently I've encountered a problem with my camera. After plugging it into my computer (And not noticing the power surge notification on the desktop while doing so). It locked up and powered itself off. I tried turning it back on, and it turned on for a split second then shut off without retracting the lense. I switched batteries and it retracted the lense, but I tried powering it on and the lense only came halfway out and it powered off. I've tried 4 fresh sets of batteries a


You sdaid power surge on the laptop.\015\012Thus suggests that this may have affected the camrera.\015\012I would think a 'repair' if such is possible will be near the cost of replacement.\015\012Only Olympus can advise ... Olympus FE-115 Digital Camera

The camera was dropped and was working for about 10 mins. then i went to turn it off and i noticed that the top lense was slightly bent. it now turns on then the start up pic shows, then the screen turns off. the lense will not go down. please help me.


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Pentax Optio M40 Digital Camera

Lense Issue When I turn on the camera the lense started to move out and then got stuck. How when you turn it on it just trys to adjust the lense but again it is stuck. I am required to remove the batteries to get it to shut off. I was going ot open the case but three of the screws requires a nice special allen wrench, but guess what, they did not provide it. Any ideas where I can score one?


Does the screw you need to remove look like a triangle with 3 points? if it does i had the same problem! went to all kinds of repair stores looking for one, turns out that is a manufacturer only tool so that we cant repair them and we have to have th ... Fuji FinePix S3000 Digital Camera

Lense problem When i turn the camera on in picture taking mode the lense does not come out all the way and if i push it again it still does not come out and then when i push the power button a third time it closes the little bit it opened... but not all the way. However if the camera is in play mode and i turn it on, the lense comes out all the way just fine... then goes back in on its own and i can view the pictures. Because of this it appears the mechanism is working fine but there is maybe


Dear jmgrev,\015\012\015\012Whenever you turn your camera on and your lens doesn't go in and out properly you are likely experiencing a lens error of some sort. Look for an error 18 or a "lens error restart camera" message. If either of t ... Canon PowerShot SD630 Digital ELPH / IXUS 65 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2016 seconds