Having problems with your Nikon D50 Digital Camera with 18-55mm Lens ?

Camera turns off. if i take out battery and put it back in i get err message. it will work for about 8 pics then it turns off again


Answers :

I would definitely contact Nikon support about this one. I've never contacted them, so I don't know what it may cost, but it sounds like an electronic failure. Most likely, it's a resistor going bad and the camera is shutting off to prevent overload, or it's simply a failure in the voltage detection. But I wouldn't advise continuing to use the camera until speaking w/ Nikon. Also, your camera may still be under warranty.
Repair Help & Product Troubleshooting for Nikon D50 Digital Camera with 18-55mm Lens

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Camera turns off. if i take out battery and put it back in i get err message. it will work for about 8 pics then it turns off again


I would definitely contact Nikon support about this one. I've never contacted them, so I don't know what it may cost, but it sounds like an electronic failure. Most likely, it's a resistor going bad and the camera is shutting off to prevent overloa ... Nikon D50 Digital Camera with 18-55mm Lens

ERR message I have an err message that displays everytime i try to take a pic...i went through reset procedure and did not correct problem ..camera worked night before during a shoot..turned on next day and did not work...we dont have a nikon repair center anywhere close...i hope it something simple that can be fixed here ..it acts like its taking a pic, then message displays and goes off after about 20 sec


I'm afraid, according to the manual you have to send it in...\015\012I would contact Nikon either through their Web site or by phone. It is normally neither expensive nor complicated to send a camera in. Just pack it well to protect it and send ... Nikon D70SLR Camer Armor Smoke Digital Camera

My Lumix DMC-FX8 shows me the message turn off then turn back on again for some reason my flash stopped working completly. and randomly it tell me to "please turn off, then turn back on" i tried everything. HELP I'm having a similar problem with my Lumix DMC-FX01. Movie taking won't work either. I don't if the camera might have gotten some moisture in it or what. Any suggestions?


I had this problem on the weekend! I fixed it with a more archaic method. When it says turn the camera off and then on again, the lens is stuck out. It only goes back in when I turned the camera off and then on for a brief second, and then pops out a ... Panasonic Lumix DMC-FX01 Digital Camera

LENS ERROR my Nixon camera was working fine one moment, I was taking pictures and then after I turned it off, I went to turn it back on and it starting zooming and making the urghtt noice as it focused in and out. it does that several times and then the lens error notice shows up on the screen. then i press power and it turns off, but when i turn it back on, the same thing happpens. In the LCD display at the back the image we try to take looks like a pic in a TV with bad signal, I tried to clean


This seems to be a problem with switch and the sensor inside the camera, Some time it works on magicaly like nothing has happend, After having this problem I have to on & off the lens for 3 or 4 times and clean the lens and 3 small holes in the f ... Nikon COOLPIX S200 Digital Camera

I have a D80 since 2 years and since last 1 week have been getting the 'Err' message. Initially, after referring to the manual & pressing the shutter release button, the camera responded only ONCE. i.e. the 'Err' message disappeared and the pics were SEEN on the screen (which means the shutter was working). Now, even that has stopped. I'm not able to click any pictures (although the mirror moves) and certain specific menus & other buttons on the body dont work. Now on pressing the shutter re


Hi sandeepbhat2, On page 129 of the D80 manual is the factory reset switch. Look on the left side of the camera there is the terminal cover, inside below the USB connector is a small reset button. Give that a try. If still it does not work you should ... Nikon D80 Digital Camera with 18-135mm Lens

Camera was on, working fine. When powering off, telescoping lens did not retract so lens remained extended just a bit with lens cover open. Waited a few minutes, turned it back on and I get the "access" display message then the beeps and (turn power off and back on) message. While off, I have removed the battery, replacing it with a fully charged spare and it still does this. The lens tries to telescope a little bit and retracts a touch, but I can't get the camera out of this mode. Can it be res


Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Sony Cyber-shot DSC-W55 Digital Camera

My Sony DSC-W30 has a problem. When turned on the screen picture rarely can be seen. It is either completely dark and a picture taken will also turn out dark and unseen. Sometimes the screen will turn on and off many times and then turn dark. Sometimes I can smack it on my hand and it will go black or come back on. The anti-shake button sometimes allows it to come back on. I do not have any screen messages and all the other features seem to work but in a dark unusable screen.


Sounds like a loose LCD connector. It does not sound like a image sensory problem to me. You will have to disassemble it , remove the connector cable then replug it back into the panel and that should do the trick. However I suggest that you take th ... Digital Cameras

Canon rebel xt eos shows ERR CF. What do I do now?I tried a new flash card but still got the same error message. When I try to preview pictures I have already taken the screen says ¨no image¨. My camera worked for a couple of pictures at one point following this initial error message and then acted up again, showing err 02. It then quickly reverted back to old error CF message.


Check that the pins in the camera that connect to the CF card are clean and not bent. You will probably need a good light and a magnifying glass to see into the card slot. If you can see a pin that is bent you could try straigtening it. BEWARE- turn ... Canon Rebel XT / EOS 350D Digital Camera

My Sony DSC-H50 Digital Camera has the following symptoms. When I turn it on, it appears as if it tries to move the lenses, but they do not move. A message appears on the screen turn the camera off an on again. This does not work. Removing the battery and then turning the camera back on does not work either. I tried initialize and reste the parameters to default, but that does not help either.I can view pictures that are stored on the camera


Http://www.sony.co.in/support/product/dsc-h50\015\012\015\012\015\012\015\012 ... Sony Cyber-shot DSC-H50 Digital Camera

KODAK CAMERA I can put fresh batteries in and take a few pics download them shut it off then turn it back on, and it will not let me, it shuts off just about as soon as I turn it on. I can take the same batteries out and put them back in and it will work for a few minutes then there it goes, its turns itself off. I went to try to get another one and they said since itwas 10 days past the 30 day limit. I had to get ahold of you. I really feel like throwing it in the dam River.


Hi,\015\012I found that most digital cameras are fussy. They need the right type of battery. Try using energiser rechargables. They last longer and are the cheapest that work. Don't bother with cheap batteries they don't work. ... Kodak EasyShare Z710 Digital Camera

8GB CENTON SDHC memory card - class 4 - worked okay first day. Removed card to transfer pics to computer. Did fine. When inserted card back in camera JVC-PICSIO GC-FM2BU, got "Memory Card Error" message. Could not reformat. Still okay incomputer, so reformatted in computer. Back in camera, got same message. Tried in other cameras - got same error message. FYI, card is NOT locked!


Sounds like you forgot to use the "safely remove hardware" when you removed the card from the computer. Also, never format a card in a computer and then expect it to work in a camera. You can try to format it a few more times in the camera but if not ... Digital Cameras

I have a panasonic lumix DMC-TZ3 camera and it's not working. When I turn it on, the lenses comes out/goes in like 3 times but it won't focus and stay open. I can't take a picture. A message says to turn it off and turn it back on again, but it doesn't work. I can view my album in the the camera....please help!


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic Lumix DMC-TZ3 Digital Camera

I took my CF card out to get photos, went to put it back in and the screen read "There is a problem with CF card. Replace the CF card." I didn't think there was a problem with the card. But I replaced it anyway. Same message. I tried to format the new card and a message read err 99 turn it off and on and reinstall battery & put it back. I did all of that. Same message about the CF card.


Your CF pins in the camera are most likely bent/broken. This is a very common problem. Most repair shops will charge $150-$200 to repair this.\015\012\015\012Hope this helps.\015\012\015\012Wes ... Canon Rebel XT / EOS 350D Digital Camera

Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work. hi expert i m suffring in this error on my panasonic DMC-LC33 when i switched on


Try \015\012\015\012Klomtrix trick this worked with my camera\015\012thanks klomtrix ... Panasonic Lumix DMC-LC33 Digital Camera

I have a Canon EOS 350D SLR (calle the EOS Digital Rebel XT in the States) that has been used daily for two years without a problem, up to now... When I switch on it gives the message "CF Err". I have removed the 2Gb CF card and it reads perfectly in a dedicated card reader. Having backed up the pics on my PC I then tried to format the card in the camera but got the message "Err 99". I then formatted the card in the PCs card reader/writer but the camera still wont accept it. I have just tried a


Turn the camera off and remove the lens and then re fit the lens and switch back on. Also cleaned the lens contacts. \015\012Err 99" includes memory card, lens contacts , battery contacts, in fact just about anywhere.\015\012\015\01 ... Canon Digital Cameras

Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work.


*&%$@#%^&*&^% !!"It's working!!!!\015\012\015\012Turn your camera on and put it near your ear. Did you hear a softly motorized sound in the lenses area and the green LED is flashing? If you hear this sound do this.\015\012\015\012Do it under your own ... Panasonic Lumix DMC-LC33 Digital Camera

When I recently turned on my camera (D-630 Zoom) to take a picture, I got the message titled Card Setup, with two options "Power off" and "Format". I turned the camera off, took out the memory card (1GB) and put it back in, as I did the last (and only) time this happened, about two years ago. But it has not worked, and I have been getting this message with the two options for a few days. Any ideas? Thank you.


If this exact card has worked in the camera before, chances are it has gone bad. Typically, if the camera says to format the card it is because it does not recognize the card. The only reason this would happen is if the card is unreadable from malfun ... Olympus D-630 Zoom Digital Camera

When i turn on my camera it turns right back off. The lens will come out as if it is about to take a pic but then it goes right back in. I cleaned the original battery and connections, still didn't work. I got a new battery and it is still doing the same thing, from the 1st time I put the new battery in.


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Sanyo VPC-E7 Digital Camera

Hi my lumix dmc-tz1 camera is not working properly. After being turned on for a few seconds a message comes on and tells me to turn the camera off and then back on. If you do this it will repeat the message again after a few swconds. It does not do this when in replay mode. any help would be appreciated. Thank you


This message appears when force has been applied to the lens. You may need service. ... Digital Cameras

This Sucks! My camera is new, I went to use it...actually for something I saw that was hillariious...and I turned it on, the lens came out...it was zoomed all the way, and I could'nt take the pic nor could I adjust the zoom. Then I got this hateful message to turn camera off then on again, which I did. Now the lens does not return apon turning the power off, but does retract and come back out when I turn it on...and then the same scenario! Help Please!!!!!!!


I think this is just a hardware malfunction(some mech. switch) because, i have a lz7 and when i deliberately open the battery case with the camera power on it obviously switches off and then when u close the battery case either with the power on or o ... Panasonic Lumix DMC-LZ7 Digital Camera

Hi I have panasonic Lumix DMC-FZ20 and when I start camera on the display it come with message "plz turn camera off and then on again." But it dont really do anything when restart occurs. It keep showing same message. Although it allow me to see old pics when started with play mode but dont start if the message has already on display. Moreover, when this message is on it wont allow me to work with any of the camera function including zoom in/out. . . Many Thanks . . .


Usually when this message pops up it indicates the lens position is jammed, you will need a camera technician to assess the item for repair cost. ... Panasonic Lumix DMC-FZ20 Digital Camera

Power doesn't work properly. When I turn off camera with power button, lense stays out. When I turn on, the lense goes in then back out again, but after a few seconds, I get the message: "Please turn camera off then on again." If I don't do anything, the camera will turn off by itself, and the lense will go in. Battery is fully charged, and nothing dramatic happened to start this problem...


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Panasonic Lumix DMC-FX8 Digital Camera

I took my camera to the beach, took a picture and put it back in my bag. I then took the camera back out to take another picture the lens extended but then it went back in again it went to go back out but stopped and a loud beeping noise started and a message saying lens error restart camera. I don't know how to restart the camera and if that means turning it of then on it still doesn't work. What can I do now?


If your camera went into "standby" mode, the lens retracted and you may have thought it was off. You put it into the bag and slight pressure on a button reactivated it and the lens tried to come out but may have been prevented by something in the bag ... Canon PowerShot A480 Digital Camera

"For" Message I was infrequently getting a "for" message, which stopped me from taking pics. I bought a new card and all was well for a while. However, it started again. I removed and reinserted the card and this seemed to work. Now, the "for" message is constantly there. The green light flashes on for a moment when I insert the card, then goes off. If I turn the camera on, the "for" message flashes on and off.


Of course the camera is telling you to format the card... you know that, right, but you don't want to because (a) it is already correctly formatted and (b) this warning happens when you are half way thru shooting.\015\012Try another card that you kno ... Nikon D70s Digital Camera

The entire zoom lens will not come out when I turn the camera on. It moves a little, makes a sound, and then my camera says turn off camera off and back on. I tried that several times and it is still not working. The battery is charged. I did go to the beach and wondering if sand got into the camera. I also cannot review my pictures as the message comes up about turning it off. What is the best solution?


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Panasonic Lumix DMC-TZ3 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2758 seconds