Having problems with your Panasonic Digital Cameras ?

I have just bought a Lumix FZ18 camera (July 08). It worked perfectly on all settings at first, but has now developed an apparent fault in which it shows an overexposed image on all settings apart from automatic. When the shutter button is partially depressed, the image in the viewfinder or on the screen shows as normal, but when the shutter is activated it immediately reverts to over-exposed and the resulting image is the same. Can you advise please


Answers :

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on.

Fix #2: Remove the batteries, then remove the memory card. Then install the new batteries, when you turn it on it should come back to life. Error E30 means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.

Fix #3: Insert the cameras AV cable, and turn the camera on in picture review mode. Have no idea why this would work, except that quite a few people have reported some success with it.

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera. The following photo illustrates unseated guide pins that would cause a lens error.
\015\012
\015\012Hopes this may help you;
\015\012
\015\012Regards,
\015\012VOTIT
I have the same camera and had the same problem about 2 months after i bought it, it is a hardware issue, i exchanged mine for another. aside from that problem they are nice cameras.
\015\012
\015\012cheers, Nick
Repair Help & Product Troubleshooting for Panasonic Digital Cameras

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have just bought a Lumix FZ18 camera (July 08). It worked perfectly on all settings at first, but has now developed an apparent fault in which it shows an overexposed image on all settings apart from automatic. When the shutter button is partially depressed, the image in the viewfinder or on the screen shows as normal, but when the shutter is activated it immediately reverts to over-exposed and the resulting image is the same. Can you advise please


Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. Fix #2: Remove the bat ... Panasonic Digital Cameras

Camera shows no image through the viewfinder or on the lcd screen.pressing shutter button will actuate the camera, but only image is of a black box.using the display button to turn off the lcd does not help. the information icons show both in the viewfinder and on the lcd. camera has not been subjected to any abuse of any kind. has not been used for about 2 months


A stuck shutter is another common failure mode for digital cameras. The symptoms of a stuck or "sticky" shutter are very similar to CCD image sensor failure. The camera may take black pictures (for shutter stuck closed), or the pictures may be very ... Canon PowerShot S3 IS Digital Camera

Coolpix L5 was functioning perfectly until today. Now it boots normally, focuses normally when the shutter button is partially pressed, but does nothing when the button is pushed all the way down. It will not shoot stills or video or even self-time a still shot. It behaves exactly as if the actual shutter release button is broken and doesn't make contact at the full pressed position. New batteries, memory card, resetting default menu settings--none of these help. It's running firmware 1.0.


ARe you sure that it is not stuck in playback mode? \015\012Here is a list of firmware and yours is not listed:\015\012 ... Nikon COOLPIX L5 Digital Camera

Every time I power up my D5000, and press the shutter button half way (to auto-focus) the image in the viewfinder shakes, and after a few seconds the image shifts slightly and something internal seems to lock into place. After this, all functions are normal, but this issue is annoying, and obviously not right. Any ideas?


Inside the lens assembly, is a circular, edge-geared focusing lens, with electromagnets on it. It has to be able to spin freely to focus, and focuses with signals from the focusing system and cpu, etc. When any dust, lint, sand, etc. get inside ... Nikon D5000 Digital Camera

Hi! I have a problem with my samsung digimax s500. My camera makes worse photos in the MANUAL Mode. They are all dark. It seems that the Exposure compensation is set at -2. The camera shows me that when i press the Shutter button lightly. But i can not reset this in the MANUAL Mode. Wich means that i get only a normal bright photo when my exposure time is set at 8 seconds. Please help me! sincerly Georg Heidfogel


... Samsung Digimax S500 Digital Camera

Camera shuts down after shutter button is pressed. It shuts down halfway through the shutter operation. Everything else works fine-reviewing pictures, settings in menu, focusing, exposure settings etc. The camera focuses ok when the shutter button is half pressed then when you press the shutter button fully, the mirror goes up, shutter appears to open then the camera shuts down with no power. Only way to get mirror etc back to normal is to remove the battery and refit. When camera is turned b


... Canon EOS 40D Digital Camera

LCD Black I went to turn on my camera and everything turned on normally( shutter opened). When we lookied at the LCD screen it is black but the icons show up. We can change setting. If you take a picture the way it is now the picture turns out black. I cannot see any images in the LCD at all. All pictures taken now are black.


Swith off the Camera and gently tap the bottom(tripod hole side) to a hard surface, I was lucky and it worked for me for the same kind of problem. ... Konica Minolta DiMAGE E500 Digital Camera

Dark exposure I have a Nkon D40x. Setting the selector to Auto, Shutter or Appature(SP) the image comes out dark. The historgram shows a spike that is totally contained in the first quarter of the screen. When I use the manual setting the image improve as the shutter speed was slowed down (1/80sec and ~7f the image improves). Any guess as to what is happening?


Check your ISO setting...should be between 100 to 400 for normal pictures.Did you change your exposure compensation setting to something other than "0"? Is the aperture ring on the lens set to the "A" position? ... Nikon D40x Digital Camera

Shutter release I just purchased this camera and while I was taking a photo indoors I pressed the upflash button and eversince then every single button I press on the camera (including the off switch) sets off the shutter release. In addition to this problem I can no longer see though the view finder unless I am pressing the shutter release button and then I can momentarily see through the viewfinder. I have noticed that if I press the shutter release button, it does not allow autofocus and it a


Take it back to the shop ... Pentax *ist DS Digital Camera

I dropped my camera and since then I can take photos, the camera focuses, my display is fine when viewing previously shot images and the normal display information but when the shutter is pressed all o see is black. I don't know if the images are being taken or if they aren't. I tried taking of the lense and pressing the shutter and a black box with a **** of light shows. With the lense on nothing but black shows. Is this issue with the lense or body? Any feedback is appreciated.


When you take off the lens and fire off a shot, does the mirror go up and return or does it stay up? If not, is it possible that it is staying up when the lens is connected? When you fire a shot, can you hear it returning? ... Canon EOS 400D / Rebel XTi Digital Camera

My Canon S3 IS compact has a viewfinder problem. Upon switching on it always shows the "settings" icons around the viewfinder but the image is not there. I have to turn the camera on and off about 6 to 10 times. The viewfinder image starts to appear dim and blurred. Finally it starts to work OK. It is 2years old and taken about 1000 images.


It sounds like the camera either has a connection for the image that isn't the greatest or the control board needs some work. You could try removing the outer panel and taking a blow dryer to the internal parts but don't let it get too warm and see i ... Digital Cameras

Cannon EOS500D, taking a picture in creative modes I have to press the shutter button twice to take a picture.(not counting the half pressing of the shutter button. the second pressing of the shutter button can be any length of time to take a picture. It seems to think there is delay set but there is not. In basic modes the picture is taken normally


Hi kevinmullen8 - was this ever resolved? My mum was mucking around with my camera (eos1000d) and I have the exact same problem (press shutter twice in creative mode). Factory reset was of no assistance.Please help!!! ... Canon EOS Digital Rebel XS / 1000D IS Digital Camera

My cibershot DSC-F717 does not have anything in the viewfinder and the LCD displays the settings and options.The screen is black with yellow words and numbers Also my zoom will not work. The LDC does not have an image on the viewfinder nor the LCD. I do have the LCD setting options displayed. The zoom will not show where the setting is on the LCD and I have checked all the settings (the focus on the zoom mode, conversion in the set up turned to off).


HelloThank you for using FixYa for your problemYour camera is faulty. It should be taken to an authorized repair centre for a repair estimate. Very few digital cameras ... Sony Cyber-Shot DSC-F717 Digital Camera

I have a Pentax *ist DL2 camera, which I bought second hand on ebay, but from a very lovely, recommended seller, so he wasn't having me on. But recently, every button I press seems to set the shutter off and it makes the clinking sound as if your taking a photo. However no photo is taken and the LCD screen is constantly **** on, although not showing any preview or menu. Also, nothing is showing out of the eye-piece so I can take any photos or do anything without the shutter going off when a butt


Take off the lens and fire off a few shots. Does the mirror flip up? Or is it permanently up? Does the shutter open? Can you see through the lens? This "lovely, recommended seller" may have unloaded his problems on you. ... Pentax *ist DL Digital Camera

Hello... I've been using my sony DSC H5 which is great but recently when I hold the shutter button down halfway to focus does not lock in the image but it does auto focus when pressing the shutter button down. I someone knows a setting to check please let me know since I am unable to find it. thanks....


You need to replace the control assembly, see the solution here:;\015\012http://www.fixya.com/support/t1811939-shutter_button_popped_off_am_out ... Sony Cyber-shot DSC-H5 Digital Camera

Focusing problems Hello, I have been trying to take close-up pictures (between 4-12 inches away from subject) but when I press the shutter button halfway, on the screen I see the image come into focus, come out of focus, come into focus,.. on and on for several moments until it settles on the out of focus image. I've tried setting the camera to the macro and super macro settings, and that doesn't help at all. I know it can focus, because I see it on the screen but for some reason it chooses the


You may be beyond (up to close) the focal capability of the lens. Even though there is a macro setting, the lens may not have the capability to focus on an object that close (without adding an external macro lens). The specification on the minimal ... Olympus SP-350 Digital Camera

White Screen Upon startup lens emerges but when screen appears it is white whereas it normally displays whatever the lens sees. When the shutter button is pressed the camera will focus and take a white picture which can be deleted. The camera does not flash although flash is set to automatic and photo taken in a dark room. Camera flashes (weakly) with flash set to manual on. Lens is unobstructed and appears to be perfectly normal. Camera was not dropped. Batteries have been changed.


\015\012Upon startup lens emerges but when screen appears it is white whereas it normally displays whatever the lens sees. When the shutter button is pressed the camera will focus and take a white pictur ... Pentax Optio E10 Digital Camera

Over exposure The exposure settings on the camera have suddenly become fixed - I can't change them either through fixing shutter speed, OEV, or any other settings. Even tried a factory reset by selecting 'initialize' from the menu, but the problem persists. High or low exposure settings are visible on the viewfinder (i.e. changing the settings shows the picture getting darker or lighter on the screen), but once the picture is shot, it's fixed at an overexposed state.


... Sony Cyber-Shot DSC-HX7V Digital Camera

My D70 was working normally when I last used it. I left it safely stored at my vacation home for three months, and when I tried to use it today it appeared to take pictures, all functions seemed to be working, but reviewing the pictures I see only a black monitor. It shows a file number, the info shows exposure details but there is no image. I did a re-set to factory spec, put in a fresh battery, tried several memory cards, all with no success. Looking at the memory card on my computer shows the


The shutter in the camera lens is not working, the motor that controls the aperture has failed or the related gears. This device will require a camera specialist to resolve the issue and an estimate recommended. ... Nikon D70s Digital Camera

Nikon d80 - most of the time memory card access lamp flashes and shutter release button doesn't trigger shutter. Sometimes it will stop blinking and camera will fire. Sometimes when it fires it will not show a preview image. When malfunctioning I can not bring up menu screen or access any features (shutter speed, f-top, or review screen. Have tried different memory cards, and lenses with no change.


Hi pantha. Turn it on and go into the menu and find the reset function. Reset it. This will merely set it at all of the parameters it was set at in the factory. IF this reset does not solve ALL of the problems, then you will have to take it or sh ... Nikon D80 Digital Camera with 18-135mm Lens

I was in the middle of shooting a wedding, when suddenly my camera said that it was 'busy' - it was taking a while to go back to normal, so I decided to shut the camera off and just turn it back on again (I didn't mind loosing the last image). When I turned the camera back on... all of the sudden the shutter kept going off extremely fast (without me pressing the shutter button). I turned the camera back off, but the shutter kept going off. I freaked out and too the battery out to make it stop.


Did you remove batteries for a couple of minutes, that is the first thing to do. ... Digital Cameras

The screen on my M380 does not show the image. The camera is fully charged and when I press the "on" button, the lens extends and opens. The screen is illuminated, but there is no image of what the picture will be. I can go ahead and take a picture -- it makes the appropriate sounds as it normally would and the flash goes off if needed. In fact, when I then plug into the computer, I can see that a picture was taken. However you cannot focus the shot because you cannot see the image on the s


This can be a settings problem on your camera, so what we can try doing here first is to reset or restore the camera's settings to its default and then after doing that power off the camera and take the battery out for 5 minutes then put it back in a ... Digital Cameras

Canon Powershot A610 digital camera--LCD screen shows icons, but otherwise is blank--there is no visible movement in the lens when I take a picture without flash--have tried setting it on TV setting and taking a picture, then opening the battery cover for a few seconds after waiting 7 seconds or so, but no images on the LCD except the camera's icons--ideas? probably a stuck shutter, or is it still possibly the CCD sensor even though there's no visible movement in the lens? Ideas? Thanks!


Much more likely that it's a stuck shutter, especially for your model camera. How many tries did you give the fix? Some people stated that it took at least 15 repeated tries before the shutter opened:\015\012\015\012\015\012 ... Canon PowerShot A610 Digital Camera

LCD does not display photo but shows settings, menu etc. Downloaded "images" show as black on computer screen but photo data is available as if the photo had actually been taken. Flash works and shutter sound effect works. Have read that there is a potential latent defect that gives rise to this problem.


This is a known manufacturing defect and Canon will fix it for free. Look for the notice and instructions on the Canon website. ... Canon PowerShot A85 Digital Camera

When i go to take a picture, the image screen shows a pink horizontal line at the top and the rest is grey. I have tried different settings and all are the same. I normally use the auto setting. It will flash when I take a picture, but there is nothing to view.


This sounds like it might be a defective CCD imager. If so, Canon should fix this for you for free worldwide, and may also include free shipping both ways (free shipping varies with countries). This is regardless of your camera's warranty status. ... Canon PowerShot A85 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2833 seconds