Having problems with your Panasonic Digitalcamera Lumix DMC-FS5EG-K black Digital Camera ?

Lense will not go in when turned of - Panasonic Digitalcamera Lumix DMC-FS5EG-K black Digital Camera


Answers :

Fixing a Lens Error on a Digital Camera
\012
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Panasonic Digitalcamera Lumix DMC-FS5EG-K black Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Lense will not go in when turned of - Panasonic Digitalcamera Lumix DMC-FS5EG-K black Digital Camera


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Panasonic Digitalcamera Lumix DMC-FS5EG-K black Digital Camera

My panasonic lumix dmc-fx3 camera does not turn on. it was working fine one day and then the next it just stopped turning on. Screen is black, lense doesn't come out. I thought it was that i'd ran out of battery but i'd charged it not long ago, anyway i charged the battery up again and it still won't turn on. Any idea what it could be? Thank you


Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Panasonic Lumix DMC-FX3 Digital Camera

Hello, I have 2 problems with my Panasonic Lumix DMC-FS4 Digital Camera. Firstly, at the lower left corner of my screen, there is a dark shade. So in all my pics, there is sth black on the lower left corner. Secondly, I can't zoom to the maximum, it says "turn off the camera" or " system error (Zoom)". Any help will be highly appreciated. Thxs :)


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Panasonic Lumix DMC-FS4 Digital Camera

Panasonic DMC-TZ4 When I switch on I get "Turn off camera and turn on again" message but it does not good. When I swtich off I get "workng hard" noises as if there is an effort to retract the lense but it will not retract unless I turn the camera on again. At that point the lense retracts and comes out again at once; more "hard work" noises and a new "turn your camera off" message. The only way to get the lense into the retrated position is to catych it at the right instant and remove the batter


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic DMC-TZ4 Digital Camera

My camm! I have an olympus digital camera fe-170. when i turn on my camera, the lense come out and the LCD screen is black, when i try to turn it off, it doesnt turn off, but after like 10 seconds it turns off by itself. but when it turns off the lense dont go back in?! then when i try to turn it on, its the same thing. when i plug it into the computer, the lense go back in, but when i unplug it from the computer and try to turn it back on again...SAME PROBLEM. i did drop it before, but can i do


I think thy will say you, replace lens unit. but lens is very expensive, so we can buy new one camera. I have the same problem, i found focusing lens wheel teeth slipping, no parts available, so i covered a gum coat on the teeth. ... Olympus FE-170 Digital Camera

I have an olympus digital camera fe-170. when i turn on my camera, the lense come out and the LCD screen is black, when i try to turn it off, it doesnt turn off, but after like 10 seconds it turns off by itself. but when it turns off the lense dont go back in?! then when i try to turn it on, its the same thing. when i plug it into the computer, the lense go back in, but when i unplug it from the computer and try to turn it back on again...SAME PROBLEM. i did drop it before, but can i do anything


The lens is bad, needs to be replaced. Maybe purchase camera on ebay with broken LCD but good lens. Replacement can be time extensive. Will need #00 or #000 phillips screwdriver and solder iron. Remove 6 exterior screws+2 inside battery door. Take of ... Olympus FE-170 Digital Camera

Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work. hi expert i m suffring in this error on my panasonic DMC-LC33 when i switched on


Try \015\012\015\012Klomtrix trick this worked with my camera\015\012thanks klomtrix ... Panasonic Lumix DMC-LC33 Digital Camera

With the Panasonic DMC-LZ2PP Digital Camera when turned on I get a black screen and no picture.


... Panasonic Lumix DMC-FX10 Digital Camera

Screen turns black when taking a photo - Panasonic Lumix DMC-LX3 Digital Camera


... Panasonic Lumix DMC-LX3 Digital Camera

Panasonic Lumix DMC-FH24 shows black spots - Panasonic Lumix DMC-ZR1 / DMC-ZX1 Digital Camera


... Panasonic Lumix DMC-ZR1 / DMC-ZX1 Digital Camera

Hi, im 14 and i got a Panasonic Lumix DMC-F3 camera for christmas and have had it for about 4 months, a few weeks ago a 1cm black dot appeared on the screen. It doesnt get bigger when i zoom in and doesnt go away even when i go to the cameras menu. today i went to turn it on and another black dot had appeared on the other side of the screen, there is also a thin black line going through the middle of the screen. i have tried cleaning the lens but it didnt make any difference. Please Help me i a


This is a faulty or damaged LCD screen. The fact that the pattern of dots and lines is unchanged by zooming and appears on the menu screen confirms it.The LCD cannot be repaired, it must be replaced. As long as the fault is not due to mis ... Panasonic Lumix DMC F3 Digital Camera

I have a panasonic lumix DMC-TZ3 camera and it's not working. When I turn it on, the lenses comes out/goes in like 3 times but it won't focus and stay open. I can't take a picture. A message says to turn it off and turn it back on again, but it doesn't work. I can view my album in the the camera....please help!


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic Lumix DMC-TZ3 Digital Camera

My sony digital camera won't fully turn on. when you push power the screen stays black but it says access and the lenses repetitively goes in and out with a 3 second pause between. then finally it stops and says to turn the camera off then back one. but this keeps occuring and it won't fully turn on. HELP!


There is some problem with your sensor in lens so only you are getting this problem .......so better check the sensor..... ... Digital Cameras

When I turn on my panasonic digital camera DMC-LZ7 (with fresh batteries) it attempts to focus but cant then displays a message saying "turn off camera and turn back on again". If i do this, the same problem appears


Looks like a problem with the CCD sensor. Try removing batteries, and SD card for 5 minutes. Replace new batteries and try again.If issue persists, you will have to get the piece serviced. ... Panasonic Digital Cameras

Hi, I have a panasonic Lumix, DMC-FS5 digital camera. When I turn the camera on and it's on 'photograph' mode, a message keeps appearing after a couple of seconds saying: "please turn camera off and then on again". I get the same message everytime and am unable to take any photos or even access the menu options. There are no problems when the mode is set to 'playback' mode. The images are still there and I can scroll through, as well as access the menu.


Hi,I had this same problem. I have just pulled the lense (not with any major strength) when it was fully extended. This seems to have solved it for me!! ... Panasonic Lumix DMC-FS5 Digital Camera

Panasonic DMC-FX07 Digital Camera won't turn on.


Check your batteries, but otherwise it could be a power board. It could cost between $90 - $125 to replace the board ... Panasonic DMC-FX07 Digital Camera

Panasonic LUMIX DMC-FX35 not turning on - Panasonic Lumix DMC-FX35S Digital Camera


... Panasonic Lumix DMC-FX35S Digital Camera

I have a Panasonic DMC-FZ30PP digital camera. I used it today and it worked fine. I turned it off and turned it on 1 hour later and it was dead. There is nothing in the way of a screen or even a beep. I switched to my spare battery and still nothing. I charged the battery and the camera is still dead. It was not dropped. What can I do next? Randy


... Panasonic Lumix DMC-FZ30 Digital Camera

Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work.


*&%$@#%^&*&^% !!"It's working!!!!\015\012\015\012Turn your camera on and put it near your ear. Did you hear a softly motorized sound in the lenses area and the green LED is flashing? If you hear this sound do this.\015\012\015\012Do it under your own ... Panasonic Lumix DMC-LC33 Digital Camera

Panasonic DMC-TZ4 lense is out when off. When I turn it back on, the lense retracks and closes and then extends again. I try to do anything with it and it says; "Turn camera off then on again." the process starts over again.


... Panasonic DMC-TZ4 Digital Camera

My panasonic dmc-lz6 wont turn on - Panasonic Lumix DMC-LZ6 Digital Camera


Replace batteries with new ones or recharge them if they are rechargeable.If this operation won't help, then check the objective, because it could be jamed or blocked - in this case the LCD shows a message:"You should turn off and on the camera ... Panasonic Lumix DMC-LZ6 Digital Camera

Black pictures I drop my a Panasonic DMC-FX10 digital camera,and now everything else is fine, but all pictures all plain black, back screen is shoving all informative text perfectly, but image part of the view is black. Preview shows older pictures fine, but the ones taken witrhthe black screen is also here black. How bad is problem and is it worth it to get it fixed?


It is worth to repair instead getting new, contact your panasonic service center ... Panasonic Lumix DMC-FX10 Digital Camera

Turn on date stamp for dmc-fh27 - Panasonic Lumix DMC-FH27 / DMC-FS37 Digital Camera


... Panasonic Lumix DMC-FH27 / DMC-FS37 Digital Camera

I have a Panasonic DMC-FX12 digital camera. Before I left on vacation, I took all the pictures OFF of the camera and recharged the battery. I took only 4 pictures before the error message "Built in Memory Card Full" came on the screen and refused to allow me to take any more pictures. HELP! A secondary problem I am having with the same camera is that I have to turn the ON/OFF switch on and off several times before the lens finally comes out.


You copied all your pictures, but they still exist on the memory card. You need to go into the menu and erase the pictures. As far as the lens not coming out, there may be some dirt in the mechanism. ... Digital Cameras

My Panasonic DMC-TZ5 will no longer focus, especially after using zoom. It displays messages re shutting camera off and on, takes 30 seconds to turn off and sounds like a ticking clock! It is only 3 months old. This is easily the worst digital camera I have ever bought and the Internet shows many people have the same problem with this camera. it should be withdrawn!!


If you mention "ticking clock" sounds, then most probably something like a grain of sand fell into the cogs in the zoom mechanism (been taking pictures on a beach? ;). Dirt gets into the mechanism through the gaps between the zoom barrels and the cam ... Panasonic Lumix DMC-FS5 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.6075 seconds