Having problems with your Panasonic DMC-TZ4 Digital Camera ?

Panasonic DMC-TZ4 When I switch on I get "Turn off camera and turn on again" message but it does not good. When I swtich off I get "workng hard" noises as if there is an effort to retract the lense but it will not retract unless I turn the camera on again. At that point the lense retracts and comes out again at once; more "hard work" noises and a new "turn your camera off" message. The only way to get the lense into the retrated position is to catych it at the right instant and remove the batter

Answers :

Fixing a Lens Error on a Digital Camera
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Panasonic DMC-TZ4 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Panasonic DMC-TZ4 When I switch on I get "Turn off camera and turn on again" message but it does not good. When I swtich off I get "workng hard" noises as if there is an effort to retract the lense but it will not retract unless I turn the camera on again. At that point the lense retracts and comes out again at once; more "hard work" noises and a new "turn your camera off" message. The only way to get the lense into the retrated position is to catych it at the right instant and remove the batter

Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic DMC-TZ4 Digital Camera

Camera lens The lens itself is making a strange noise and it is having trouble adjusting itself when the camera turns on. When I attempt to turn the camera on all you are able to see is a black screen and there is also a buzzing noise which I assume is the lense trying to adjust itself. The lens is trying to push itself outwards but it is getting stuck. I'm not exactly sure what is wrong with it but I assume that once Iam able to fix the lens I will be able to use the camera normally again.

Broken gears is common on the sony cameras. They have very brittle gears and have more torque then the gears can handle. They just break teeth off. There was probobly some small debris (sand,dust) stuck in one of the teeth and it got to that point an ... Sony Cyber-Shot DSC-P72 Digital Camera

My camera lense is stuck out and when I turn on the camera it makes a funny noise and says "lense error" on the screen. Is there anything I can do to fix it myself before taking it to get fixed?

Sounds like the camera lens is jammed. Before you take it to become repaired, try cleaning the crevices of the lens module to make sure there isn't any loose dirt or debris in there. Try applying very gentle pressure to the lens and see if it retract ... Nikon COOLPIX S570 Digital Camera

I have a sony cybershot, model DSC-W55. when i press the power on button, the camera does not turn on as it usualy does. instead, i get a black screen with the word Access on it. (also, when i turn the camera on, the lenses keep going in and out more frequently than before.) so the screen Access screen is just there right now, but when i click buttons like menu or display it makes beeping noises and it says 'press power on and off again '. i can still view the pictures i've taken but can't seem

You can try contacting Sony - maybe through online chat if its available for free. From what you have described, it sounds like a hardware failure. Contact Sony, and if it is a hardware failure, they will replace it for free. Or, if you have bought i ... Sony Digital Cameras

When camera is turned on the lense goes out and in and then out and stays out making clicking noises, and then we get a blue screen and camera will not work thank you for any assistance you may be able to offer.

Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Olympus FE-180 Digital Camera

Power doesn't work properly. When I turn off camera with power button, lense stays out. When I turn on, the lense goes in then back out again, but after a few seconds, I get the message: "Please turn camera off then on again." If I don't do anything, the camera will turn off by itself, and the lense will go in. Battery is fully charged, and nothing dramatic happened to start this problem...

HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Panasonic Lumix DMC-FX8 Digital Camera

I cannot turn the camera on. I guess it was dameged during my holidaying. I recall that, the camera was excidently turned on inside its holder and as the mechanism tried to push the lense out from the body it was blocked by the bag holding the camera. Now, when I try turning the camera on, the lense could not move forward at all. It gives cracking noises and turns itself off. Could this problem be fixed or better to buy a new camera? Arthur

If your camera isn't under warranty, I think that it has no worth to repair it by the after-sales.\015\012But you can try to fix it by your self, anyway there will be no loss for a bad camera.\015\012May be this post will be any helpful: ... Pentax Optio 60 Digital Camera

I dropped my Nikon Coolpix S600 camera on the floor at a concert and now when I turn it on, it says LENSE ERROR and shuts off right away.. and the lens doesnt come out. It just makes a weird noise! Is it done for or can I fix it. I can't get it fixed.

There are some fine gears that move the lens in/out ... if it dropped on the extended lens then its likely a gear was broken or knocked out of place .. it is likely repairable but its really tricky working on these things .. there are fine wires and ... Nikon Coolpix S600 Digital Camera

I get E18 message when I turn on the camera-with clicking noise-and the lense doesn't open-can't take pictures or download

... Canon PowerShot A95 Digital Camera

After my Nicon coolpix S570 has dropped on the floor, the lens does not work and when i turn on the camera, i hear a noise and get a message for lense error.

You have stripped the lens gearing you will find that you need to have the lens gogs replaced a very expensive repair sir. it may be time to buy a new one sorry take care may you and yours have a happy new yr ... Nikon COOLPIX L3 Digital Camera

Dropped approx. 3 feet onto carpet. Camera was on and lense extended. It would power up, get into capture mode and flash "sensitivity" and a green light LLC. After about 50 on & Off's the camera turns on but doesn't come out of playback. I have to open the battery compartment and close it then when I turn it on it will go into capture mode. When I take a picture it is washed out with lots of little vertical lines. Did the lense get knocked out of whack? Can I reset this? Any help will be ap

Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Pentax Optio M20 Digital Camera

Hi there, my Samsung WB500 camera can not get it's lens closed. It stands open all the time and is doing nothing. When I turn the power on, it 3 times makes a hard noise 'peep peep peep', no display and then shut itself down. What can it be? Can I solve the problem myself? Thank you! greetings Remco

This is a common problem with cameras. They can get bumped when the lens is out, and that can jam the gear assembly, or break a gear. I could run down all the things you can try to free it up, but there is a better web page that deals with issue ... Digital Cameras

I have a canon powershot A470 and it fell in water. after i removed the card and batteries of which still worked and neither were wet, i let the camera dry for a couple of days. it has turned on since and the screen would come on and show me the pics on the card but it kept turning itself off and the zoom lense would go in and out on it's own. now, i can't get the camera to turn on and the zoom lense it stuck. any ideas??? or should i call it a wash. i really love this camera!!! Theresa

I submerged my powershot for a couple of seconds. it did get completely wet. it was acting very strangely: the lcd wasn't working, the little orange light on the front kept flashing, and it took a few tries for the lens to extend.then ... Canon PowerShot A470 Digital Camera

Broken Lense My VPC-E760 Sanyo camera is a little over 4 mo. old. It was dropped about the 2 mo. i had it. Then lense popped back ito place, but it makes a funny noise when turning on and off. (or going in and out when previewing pics). Last night, it was working fine then turned off, said 'lense error 25' 'lense error 22' and 'lense error 12'. I don't know why! I tried to find out what it meant, but i couldn't SOMEONE HELP!!! lens will not go in. camera reads lens error 12 and 25

\012\012try these:-\012\012\012connect it to pc and on it\012vaccum the barrel of lens\012changing mem. card and batt. for 2min. ... Sanyo VPC-E760 Digital Camera

When turned on lense would only retract partially and then turn off. took it apart. I have it to where the camera will now go on, am able to take a photo (all normal) except I cannot get the lense to "attach" to the camera properly. Cylindrical lense. three screws protruding from it. not sure if the lense mounts on a black ring on the front or under the ring. The "in out" mechanism works but it will not grab the lense (cover?) to move out then retract. Seems to need to attach under the ring but

Good day,This is a common problem and sometimes can be fixed.Please see details on my tip on how to fix this error here:http://www.fixya.com ... HP Photosmart M415 Digital Camera

HELP! :( I was messing around with my camera, and I dropped it. HARD. the lense was popping out... so I thought I could fix it. Now the mini lense is pushed in like when it's off, but the outer lense part keeps turning a little when I try to turn it on. Please help!!! I THINK I KILLED MY CAMERA :(

... Samsung ST90 Digital Camera

The camera turns on, but the lense makes a clicking noise and then the screen says Turn the power off and on again. I have tried this, and also tried resetting it but nothing works. The lense also does not retract, even when the camera is off.

Your problem may be due to weak/worn out batteries or corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: rem ... Sony Cyber-Shot DSC-P200 Digital Camera

When i turn my fujifilm finepix s8100fd camera on the lense will pop out as normal initially then the screen will say lense error, and the camera will make a funny noise and the lense will go back in, it will pop out again when i use the zoom button, how do i fix my camera =S

HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Fuji FinePix S8100fd Digital Camera

I have just downloaded the camera on to iphoto and have cleared the camera memory . I clicked the eject icon on iphoto and once cleared unplugged the USB download cable . I have just pushed the power button to turn the camera on and firstly get the message on the camera screen "Access" then a message comes up saying "turn the power off then on again " When I do this the same process repeats itself . The lenses wont open and protrude out of the camera ready to take photos. The battery has ju

Sounds like you did two things wrong...you deleted/erased/or formatted the camera using the computer. You disconnected the camera without using the "safely remove hardware" function. ... Sony Cyber-shot DSC-W50 Digital Camera

Lense Issue When I turn on the camera the lense started to move out and then got stuck. How when you turn it on it just trys to adjust the lense but again it is stuck. I am required to remove the batteries to get it to shut off. I was going ot open the case but three of the screws requires a nice special allen wrench, but guess what, they did not provide it. Any ideas where I can score one?

Does the screw you need to remove look like a triangle with 3 points? if it does i had the same problem! went to all kinds of repair stores looking for one, turns out that is a manufacturer only tool so that we cant repair them and we have to have th ... Fuji FinePix S3000 Digital Camera

Lense stuck my kodak camera (the C663) is jammed in the outward position. its off and when i try to turn it back on it makes this wierd humming noise and turns back off. i tryed taking the batteries out charging them, nothing. i even tryed to turn it on then off quickly and tryed to help the lense back in.

... Kodak EasyShare C663 Digital Camera

I have a fuji finepix S5100. Sometimes when I turn on the camera the lens won't move and I get a zoom error message. This morning when I turned on the camera the camera can on as it should but the lens makes a clicking noise that it didn't used too. Can this be fixed? My husband is not afraid to tear into anything, if he just had some direction.

Hi.This is a common problem , generally indicated as lens error. The problem is often caused by dirt or dust in the lens gearsPossible reasons are :* Faulty lens mechanism or jammed lens (camera usually turns off b ... Digital Cameras

I have an Sony Alpha 100, when I turn the camera on with the 18-70 lense the camera makes a terrible noise and does not focus. Camera works fine with the zoom lense.

... Sony Alpha DSLR-A100 Digital Camera

I turned on my samsung sl202 and the lense come out making a funny noise but the lcd screen doesn't turn on. And then the lense gets stuck out and wont turn back off. But I can still view the pictures.

HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Samsung SL202 Digital Camera

Locked lense lense (optical aspheric lense) is locked and wont open and close normally and now i cant even turn my camera on or charge it or get pics frm the camera on the computer..! help me please..

Try these procedures.The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it in ... Kodak Easyshare M753 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3858 seconds