Having problems with your Panasonic Lumix DMC-FX30 Digital Camera ?

The lens wont go down and wont turn on - Panasonic Lumix DMC-FX30 Digital Camera


Answers :

Fixing a Lens Error on a Digital Camera
\012


\012

This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
\012

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
\012

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Repair Help & Product Troubleshooting for Panasonic Lumix DMC-FX30 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The lens wont go down and wont turn on - Panasonic Lumix DMC-FX30 Digital Camera


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Panasonic Lumix DMC-FX30 Digital Camera

Lumix fx30 wont turn on after i drop it - Panasonic Lumix DMC-FX3 Digital Camera


The first thing I would check would be the battery compartment, the Lumixes have horrible battery connectivity but can usually withstand some pretty heavy drops. Open the battery compartment and wiggle the battery about when you are turning it on and ... Panasonic Lumix DMC-FX3 Digital Camera

The lens wont open when i turn it on - Panasonic Lumix DMC-FS3 Digital Camera


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Panasonic Lumix DMC-FS3 Digital Camera

My digital camera, Panasonic Lumix DMC-LZ2 has the lens stuck. The display says "Please turn camera off and then on again" I tried blowing compressed air around the lens already.


Hi,\015\012\015\012I had the same problem with the same camera, and i also tried compressed air but it doesnt work,\015\012\015\012Finally I left the camera upside down for about 5 hours and it magically came back to life..Try ... Panasonic Lumix DMC-LZ2 Digital Camera

Lens is stuck and crooked on lumix camera - Panasonic Lumix DMC-FX30 Digital Camera


... Panasonic Lumix DMC-FX30 Digital Camera

My panasonic dmc-lz6 wont turn on - Panasonic Lumix DMC-LZ6 Digital Camera


Replace batteries with new ones or recharge them if they are rechargeable.If this operation won't help, then check the objective, because it could be jamed or blocked - in this case the LCD shows a message:"You should turn off and on the camera ... Panasonic Lumix DMC-LZ6 Digital Camera

Digital camera got dropped into the sand, and some sand worked its way into the lens and focusing system, and now the camera cannot zoom or focus, but still turns on and takes pictures i have a lumix dmc fx12, and it got dropped into the sand at the beach. the shutter wont close properly, there's sand in the lens, and it won't zoom. Please help!! i don't know how to fix it!!


THIS SOUNDS TERMINAL, BUT YOU MIGHT TRY USING CANNED AIR LIKE YOU USE TO BLOW DUST OUT OF YOUR COMPUTER, AND SEE IF IT HELPS ANY. MOST OF THESE CAMERAS ARE MADE WITH THE IDEA THAT THEY WILL NEVER BE TAKEN APART OR OPENED FOR CLEANING ETC. SO, THAT IS ... Digital Cameras

Panasonic Lumix dmc-fz8 I turn the camera on, it wont focus and the lens doesnt start coming out. Then it says remove lens cap and press > button. Even though my lens cap is off


Hi,\015\012When the lens cap off there will be sensor inside your camera it will switch on automatically perform the normal functioning of camera . You are facing this problem due to defective sensor . You need to take to service center to repa ... Panasonic Lumix DMC-FZ5 Digital Camera

Panasonic Lumix DMC-TZ3 Digital Camera mesaage says turn camera off and on tis has no impact also the lens will not retract


Hello, i did get also same message and lens did stay out. did put camera in play back mode and in menu did reset everything. now it works again. maybe i was lucky, maybe this is ,,the"solution.\015\012Jack ... Panasonic Lumix DMC-TZ1 Digital Camera

Camera lens wont close - Panasonic Lumix DMC-TZ3 Digital Camera


Dsfsdafasd ... Panasonic Lumix DMC-TZ3 Digital Camera

My camera wont turn on i tried a new battery - Panasonic Lumix DMC-FX01 Digital Camera


... Panasonic Lumix DMC-FX01 Digital Camera

Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work. hi expert i m suffring in this error on my panasonic DMC-LC33 when i switched on


Try \015\012\015\012Klomtrix trick this worked with my camera\015\012thanks klomtrix ... Panasonic Lumix DMC-LC33 Digital Camera

Lumix DMC-FX30 Digital Camera: hi well when i turn my camara on it tell me please...


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that ... Panasonic Lumix DMC-FX30 Digital Camera

I have a small Panasonic Lumix DMC-TZ5 camera. After fully charging the battery I am all of then sudden getting this error message :"please turn camera off and then on again." When the camer is OFF the lens is extended and open. When I move the camera to ON the lens moves in to the closed position closes, then reopens, extends, tries to focus, is unable to and the error message appears "Please turn camera off and then on again" This cycle just repeats. The lens is able to extend it is not st


Hi,Checkout this tip about digital camera error messagesLens Errorfix for Digital Cameraheatman101 ... Panasonic Lumix DMC-FZ7 Digital Camera

It doesnt turn on - Panasonic Lumix DMC-FX30 Digital Camera


It is possible that the battery is completely dead, in which case you'd have to replace it. If you have a spare battery, try that. If it is under warranty, send it in. If not, I'd try getting a cheap replacement battery on eBay (or charging the or ... Panasonic Lumix DMC-FX30 Digital Camera

Panasonic Lumix DMC FX 33 wont focus and shows ''please turn camera off and then on again'' and the lens stays out when switched off.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Panasonic DMC-FX33 Silver Digital Camera

I have a Panasonic LUMIX DMC-ZS19 Digital Camera and the lens seems to be stuck. When I turn it on I get a message that says, "System Error (Zoom)." Any way to fix on my own?


Try these procedures: http://www.fixya.com/support/r13011856-lens_error ... Panasonic Lumix DMC-ZS19 Black

HELP ME my Lumix DMC-FX8 lens wont go back into the camera and will only allow me to preview my pictures ...Please I am in Hawaii right now and the lens is stuck out and wont go in and it says Turn off and turn on camera again ....PLEASE Please someone help me


I read the previous answer, as I have exactly the same problem. So I decided the camera was dead. Having done this I resetted it via the menu - settings - reset. Then I turned it off and smashed it really hard against a flat surface three or four tim ... Panasonic Lumix DMC-FX8 Digital Camera

Lens wont open on Panasonic Lumix DMC-TZ3 - Sony Cyber-Shot DSC-T1 Digital Camera


... Sony Cyber-Shot DSC-T1 Digital Camera

My panasonic lumix dmc-fz7 digital camera wont turn on anymore


It takes very little moisture to stop a digital camera cold, once in it eats away the surface mount parts making it useless. I suggest replacing the camera and save your money. ... Panasonic Lumix Digital Cameras

Panasonic Lumix DMC-LZ2 Image 'melts' into streaky vertical lines when camera is turned on. This problem started occuring immediately after I found my kids deliberately turning the camera off while jamming the lens cover open, so they could get the 'turn camera off and then on again' error message (yes, I know - they've been banned from touching it again). I confiscated the camera, turned it off and it sat unused for about 3 days. When it was next turned on, the image on the LCD screen was


... Panasonic Lumix DMC-LZ2 Digital Camera

Frozen Camera I have a Panasonic Lumix TZ3 digital camera. The last time it worked, the screen went checkered, so i turned it off. But upon turning it off, the lens of the camera stayed out like it was taking a picture. Now it won't turn on. I've tried recharging the battery, changing memory cards, no memory card, switching settings and turning the on/off switch. Is there anything to be done or I do I just need to get a new camera?


Try letting it drop about 4 tto 6 inches on a hard service covered by a paper towel. Don't let it land on lens of course. You can remove the mem card. It has 13Meg of internal. ... Panasonic Lumix DMC-TZ3 Digital Camera

Panasonic LUMIX DMC-FX35 not turning on - Panasonic Lumix DMC-FX35S Digital Camera


... Panasonic Lumix DMC-FX35S Digital Camera

Driver camera lumix FX30 - Panasonic Lumix DMC-FX30 Digital Camera


Please download it here :\012www.panasonic.com/business/provideo/support/fcphd.asp\012 ... Panasonic Lumix DMC-FX30 Digital Camera

Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work.


*&%$@#%^&*&^% !!"It's working!!!!\015\012\015\012Turn your camera on and put it near your ear. Did you hear a softly motorized sound in the lenses area and the green LED is flashing? If you hear this sound do this.\015\012\015\012Do it under your own ... Panasonic Lumix DMC-LC33 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5225 seconds