Having problems with your Panasonic Lumix DMC-FX8 Digital Camera ?

Lenses is stuck open and clicks when I attempt to switch to off. The camera was not dropped. It worked fine moments before this.


Answers :

Fixing a Lens Error on a Digital Camera
\015\012
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Panasonic Lumix DMC-FX8 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Lenses is stuck open and clicks when I attempt to switch to off. The camera was not dropped. It worked fine moments before this.


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic Lumix DMC-FX8 Digital Camera

While at the beach, someone threw a frizbee at my wife and she dropped the camera in the sand. We were careful as we could be picking it up to avoid entrance of sand into the camera. It worked fine until the next day and the lens opened and stuck. I opened the case to remove and sand that entered the camera. While removing the flash it went off and now the camera doesn't even turn on. I assume something touched and blew a fuse. Is this fixable and if so where do I start?


Well, your mistake was opening the camera. You will need to have it serviced. ... Canon PowerShot SD890 IS / IXUS 970 IS Digital Camera

Lens stuck Please help me, I tried to turn on my camera today (it had been working fine before) and when I tried to switch it on the lens would not fully it open and my camera was making a whirling noise. The screen is black and will not take photos. The lens won't open fully and when it does eventually close has difficulty doing so. The camera then makes a beep beep beep noise and displays "Please turn the power on and off again". Please help I can't live without my camera and can't afford


If the lens is not coming out, its stuck, or it wont completely open or close, that is the lens assembly, that needs to be repaired. You need to take it to somebody, that can either repair it or replace it for you. There is nothing that can be done, ... Sony Cyber-Shot DSC-P8 Digital Camera

I have a Canon camera, which worked fine. I had to recharge teh batteries often, that was all. Last night, i took it out. In view mode, the camera does not shut off. The moment i switch to camera mode, the lens opens out and then the camera shuts off. What do i do pls? Any help appreciated


I'm assuming you're talking about a point-and-shoot model, and not the\015\0121000D as the category suggests. Camera mode has significantly higher\015\012power requirements than viewing mode. It is possible that your\015\012rechargeable battery has d ... Canon EOS Digital Rebel XS / 1000D IS Digital Camera

Something sticky spilled on my camera when my daughter spilled her juice cup into my diaper bag which had my sony cybershot in it. Now the lens will not open it is stuck, everything else works fine, i have taken the camera apart and just cannot figure out how to get the lens to unstick, please help, i'm 9 months pregnant and want the camera for the birth!!!


... Sony Cyber-Shot DSC-P200 Digital Camera

A640 Lock-up Hi, The camera was working fine up until today when I took it out of the case, it was stuck, locked-up somehow. I haden't used it in a couple of days (had never had a problem with it before), and now, the only sign of life when pressing the ON/OFF button is the small green light underneeth turns on but nothing else powers up or happens. The only way to get the green light off again is to take the batteries out. Also, the lens is stuck open, and the zoom partially out. What should I


Take out the OTHER battery, the one that maintains the date / time and then the camera can 'reboot' cleanly when you put some fresh batteries in it. ... Canon PowerShot A640 Digital Camera

Canon A40 Shutter Stuck The Camera works fine with all icons but it appears that the shutter is stuck open causing a black screen. Please advise how to solve this problem by myself. thanks and regards


This sounds like it might be a defective CCD imager. If so, Canon should fix this for you for free, including free shipping both ways. This is regardless of your camera's warranty status. Please check the following two links for more info:\015\ ... Canon PowerShot A40 Digital Camera

When i turn on the camera the lens wont pop open even when the battery is fully charged.... i was taking pictures and it working fine turn the camera off and on again then the lens wont open anymore? i can still view all the pictures i took from the camera but cannot take pictures anymore coz of the lens wont open. i tried initializing the camera by going to set up it didnt work..msg error said turn the camera off and on again and i did but didnt work either many times i tried please help thnks!


The problem is\015\0121- some dirt somehow got on the outside of the lense. After it was retracted fully in, it prevents the camera from opening again. When you turn it on, if it opens a little bit, try to pull it out NOT too hard and let go ... Sony Cyber-shot DSC-N2 Digital Camera

Hi there, I used my camera in sea for many times, always was working nice. But some days ago I went to sea and the camera stopped working the flash. I left overnight off and next day it was working normally again. Then when I went to sea again (always about 2 or 3 metres deep) and the camera simply stopped work. I opened the card and batterie compartment was dry and fine, when I opened the compartment where I use for connect the USB cable was very wet. I left the camera off for 3 days to dry and


It still amazes me how many people buy these cameras that are seemingly "waterproof" and eventually have the very same problems you are now having. The only true underwater camera is one in an underwater housing. ... Olympus ? 1030SW Digital Camera

Camera won't turn on when trying to take pictures but works fine to view pictures already taken. Lens is stuck open. Changed batteries several times.


Good day,This is a common problem and sometimes can be fixed.Please see details on my tip on how to fix this error here:http://www.fix ... Sony Cyber-shot DSC-S600 Digital Camera

My camera worked fine one day, then it was in my purse. When I went to use it the light was on and the screen said there was a lens error. Everytime I try to turn it on now it makes a grinding noise and refuses to open and then closes completely with the lens error reading For no reason my camera (Nikon coolpix model S210) doesn't want to work with the term "Lens error" and lens won't come out WELL YESTERDAY MY NIKON COOLPIX s210 DIGITAL CAMERA WAS WORKING PERFECTLY FINE THEM I GOT UP TO TAKE P


\012\012try these:-\012\012\012connect it to pc and on it\012vaccum the barrel of lens\012changing mem. card and batt. for 2min. ... Nikon Coolpix S210 Digital Camera

Not shure why but the camera was working fine and then i wanted to take a photo recently and the lens protector wont open. i have to hold it open and turn it on then it stays open and works fine. this is extremely irritating and it takes a small bit of the bottom corner. how much is it going to cost me to fix?


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Olympus Stylus 770 SW Digital Camera

Camera problem My daughter just received a new HP635 camera for her birthday. At first the camera worked fine, but after a few minutes of use, the camera started flashing the welcome screen repeatedly and the zoom lense would move in and out over and over until we opened the battery storage compartment of the camera. Opening the battery compartment is the only way to turn the camera off. Everything on the camera becomes inoperable when this process starts which now is every time the camera is tu


I HAVE A HP R740 SERIES DIGITAL CAMERA. IT IS ABOUT A YEAR OLD. WHEN I TURN IT ON, HALF OF THE VIEWING SCREEN LOOKS LIKE A SCREEN. ... HP Photosmart 635 Digital Camera

I have a Nikon D70 camera. I'm using a Lexar 2GB card inside. Problem focuses on the card. Previous to this moment, card has worked fine. Today, shot photos and when I hooked up the camera to download the pics, got an error in the viewfinder (CHR). Looked at the manual, and it said problem was with the card. I removed the card, and placed it in a card reader. It worked fine and I was able to transfer the photos. Replaced the card, and still get the same error. I've already re-formatted the card,


First, memory cards don't last forever, so it may be time for a new card. Make sure you check the pins in your camera and the contacts in your card for dust/dirt. I'd guess you already looked at this, though. \015\012\015\012I've had s ... Nikon D70 Body Only Digital Camera

My Kodak Z1012 is camera doesn't work. I sent it to Kodak because it had a 1 year warranty. They mailed it back and said everything was fine but it still didn't work. I researched and many people said that it was the battery and that I needed to use a specific kind of Ion battery. I bought a Kodak KLIC 8000 rechargable battery and it still doesn't work. My year warranty has passed and now I am stuck with this camera that doesn't work. Any suggestions? Thank you.


When you received the camera back from Kodak and you found it didn't work, you should have immediately contacted the support techs at Kodak and explained your situation. Then you would have been issued a complaint number and your camera could be retu ... Kodak EasyShare Z1012 IS Digital Camera

Lens stuck The camera lens is stuck in the out position and the camera won't turn on at all. The camera was working just fine a the day before this happened. I have replaced the batteries and attempted to turn the camera on an off several times.


Lens unit faulty and camera has gone into error mode. Repair lens ( several possibilities here ) and reset camera and it will work fine. ... Fuji FinePix S3100 Digital Camera

I have a samsung L200 digital camera. It was working fine until my 2 year old little girl decided she needed to play with it. Not sure if she done something or not but now the camera will not work. When I try to turn it on the power button lights up but that is all that happens. The screen does not come on or anything else. Also the lens seems to be stuck and will not go back in. And I also just noticed that the power button will only turn the camera on but will not turn it off. I was trying to


Sounds like she may have dropped it and caused a lens problem. I don't know how much damage you've done so far in attempting to disassemble it but, if you can, put everything back and try the following:\012\012 ... Samsung L200 Digital Camera

I have an Olympus Camedia C-50 Zoom camera that has worked fine for a few years, but suddenly when I open the lens cover, the camera does not turn on. I charged the battery and it is fine, and I can use the quick view button in the back to see what I have already taken, but the lens will not come out and turn the camera on. What can I do?


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Olympus Camedia C-50 Zoom Digital Camera

My camera was working fine and then it gently rolled on to the rug and then it never worked right since. I got the code in the corner of the display E18 and I cannot do a darn thing with the camera now. Should I just chuck it ? ??? Its a cannon power shot A400. (When I turn it on the display light comes on and it beeps numberous times and then the E18 signal comes on and then it goes away and the camera turns off. I do not even think the shutter opens up ) The batteries are charged so what now.


... Canon PowerShot A400 Digital Camera

When I first but film in and turm camera on it works fine, but when I turn it off, it reverses itself. When I turn it back on the shutter opens but then recloses, and nothing works. The only to get it working again is to open the film door.


This camera has developed a "Brain" fault, unfortunately, the camera, is reading the sensors wrong, and this is mucking up the whole thing, it is freezing up, and when you "open" the Film Door, this is "Sensed" and the System then send a "Reset" sign ... Digital Cameras

I am having power supply and lens problem with a canon sd1000 digital camera. its not working with the battery inside and the lens got stuck and was not closing and now it is open but the camera is off and the lens is also extended the battery is fully charged and functional but still is not powering the camera back on. i currtently took the outer casing off and attempting to navigate through the boards looking for a solution to the power supply and then the lens error of bein stuck problems.


This is a mechanical fault and would only be repaired through servicing. You should be able to get it repaired under warranty or a camera centre. If the costs are too high it may just be worth replacing the camera. ... Canon PowerShot SD1000 Digital Camera

I am having power supply and lens problem with a canon sd1000 digital camera. its not working with the battery inside and the lens got stuck and was not closing and now it is open but the camera is off and the lens is also extended the battery is fully charged and functional but still is not powering the camera back on. i currtently took the outer casing off and attempting to navigate through the boards looking for a solution to the power supply and then the lens error of bein stuck problems.


This is a mechanical fault and would only be repaired through servicing. You should be able to get it repaired under warranty or a camera centre. If the costs are too high it may just be worth replacing the camera. ... Digital Cameras

I am having power supply and lens problem with a canon sd1000 digital camera. its not working with the battery inside and the lens got stuck and was not closing and now it is open but the camera is off and the lens is also extended the battery is fully charged and functional but still is not powering the camera back on. i currtently took the outer casing off and attempting to navigate through the boards looking for a solution to the power supply and then the lens error of bein stuck problems.


I am afraid you have the notorious lens stuck problem. If you google "canon lens stuck" or "canon lens not retracing" the results will be in millions. Canon's quote for repairing this issue is well over the cost of the camera itself. However all is n ... Canon PowerShot SD1000 Digital Camera

Lense problem When i turn the camera on in picture taking mode the lense does not come out all the way and if i push it again it still does not come out and then when i push the power button a third time it closes the little bit it opened... but not all the way. However if the camera is in play mode and i turn it on, the lense comes out all the way just fine... then goes back in on its own and i can view the pictures. Because of this it appears the mechanism is working fine but there is maybe


Dear jmgrev,\015\012\015\012Whenever you turn your camera on and your lens doesn't go in and out properly you are likely experiencing a lens error of some sort. Look for an error 18 or a "lens error restart camera" message. If either of t ... Canon PowerShot SD630 Digital ELPH / IXUS 65 Digital Camera

Lens error my lens is stuck open and the camera won't work my camera fell and the lens stayed stuck and it reads lens error.... it turn it on and it turns off by itself.....i can still see the pictures i took... what can i do???


Ave you tried replacing the batteries with new, fully charged ones? when the battery is low the lens will just stay out because there isn't enough juice for it to retract, but you can still browse your photographs beacuse it uses less power. ... Casio Exilim EX-Z750 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4558 seconds