Having problems with your Panasonic Lumix DMC-LZ5 Digital Camera ?

I have a Panasonic Lumix DMC-LZ5 when i turn it on the zoom gos to 6x and then i have a message that says turn off the camera and then turn it on it happens the same again


Answers :

Fixing a Lens Error on a Digital Camera
\012
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Panasonic Lumix DMC-LZ5 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Panasonic Lumix DMC-LZ5 when i turn it on the zoom gos to 6x and then i have a message that says turn off the camera and then turn it on it happens the same again


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Panasonic Lumix DMC-LZ5 Digital Camera

There are several problems with my camera one of them is the fact in that Every time i turn on my Lumix 10x mega pixel camera the lens won't focus it also won't let me take any pictures. When i turn the camera off the lens won't go back into the camera but when i turn it back on the lens gos in and then out again. There is one more problem whenever i go to look at the pictures on play i can look through a few before its says "please turn camera off then on a again" it also says the same message


OK, if there is sand in the camera, the gears will bind or stop causing the error that you described. I think it needs to be taken apart and cleaned by a service center before using again. Or you could buy a spare caemera to use on your family holida ... Digital Cameras

The camera says please turn camera off and then on again every time i turn it on same problem as the "guest" described: the camera says please turn cmaera off and then on again... but nothing happens. i can see the picutres but i am not able to take pics or to download them. any suggestion will be much appreciated!!!!


Mine did this....New batteries did the trick... ... Panasonic Lumix DMC-LS75 Digital Camera

Battery Problem I bought a Nikon Coolpix L12 Digital Camera this past summer and have had no problem until last night. My camera turned off and said "battery exhausted." After changing the batteries twice with new batteries, the lens would open for a second then close and the camera turned off once again saying "battery exhausted." I don't know what happened. I had same problem. No matter how many times I have changed batteries, It works for a second then closes with signal saying "warning batt


These cameras have a internal battery that holds data for the camera to keep its settings. These batteries can be replaced but the camera has to be disassimboled to change it they should be able to be changed at a local camera shop pretty cheap. ... Nikon COOLPIX L12 Digital Camera

Sony-cyber-shot dsc-w50 I blieve that the battery if fully charged however when I turn the camera on all i see is a blank screen saying "access" with the lense zooming in and out then a message comes up on the sceen saying "turn camera on and off" I do this and the same thing keeps happening, could you please help? Sara


Lens unit is faulty, may have had sand or damage at some time, focus assembly inside the lens is not focussing ... Sony Cyber-Shot DSC-S40 Digital Camera

When ever I try to use the zoom button I get a message saying system error (zoom) I have also gotten a message that says Please turn off camera and turn on again... What is going on with my camera and what needs to happen to get it fixed!


When you first switch on the camera the lens will motor forward?\015\012\015\012If it does so then either the zoom control button is faulty or the control pcb \015\012\015\012If the lens does not move on first switch on then i ... Panasonic Lumix DMC-FZ28 Digital Camera

When I plug the camera in it says the usb device could not be found. Everything worked great and now it does this on every PC I try it on. I tried to reload the usb drivers for it and it says they are not needed and won't let me go any further.............. this was happening with my iPod, too, but I took some advice and turned if off, plugged it in, and reset it while plugged in and it worked. I don't know how to reset my camera, though. Just turning it on and off or taking the batteries o


Please downloaded it here :\012www2.panasonic.com/consumer-electronics/support\012\012 ... Panasonic Lumix DMC-LZ2 Digital Camera

When i turn my camera on it it has a p in a red square and it says across middle of screen turn camera off and on again but nothing happen the same screen comes up even the lenes dont move out when you turn on plz can you help


... Fujifilm Finepix S2980

Lens error When I turned my camera on, it beeps and says "lens error, restart camera" but when I turn off and turn on, the same thing happens. The lens is stuck open.


Try these procedures. Many of the steps are applicable whether the lens is extended or retracted. ... Canon PowerShot A450 Digital Camera

I bought a Nikon Coolpix L27 Digital Camera this past summer and have had no problem until last night. My camera turned off and said "battery exhausted." After changing the batteries twice with new batteries, the lens would open for a second then close and the camera turned off once again saying "battery exhausted." I don't know what happened.


... Digital Cameras

Camera Everytime I turn my camera on it comes on, but the lens goes in and out a few times before the screen goes completaly black and says to turn the camera off then back on again, I do, and the same thing happens all over again, not allowing me to take any pictures. However, I can still view the pictures that have been taken...and that are on my memory card.


It a lens misalignment try tapping the lens gently in an opposite direction the camera dropped on and that should pop the gear back into place ... Sony Cyber-shot DSC-W70 Digital Camera

Battery Problem I bought a Nikon Coolpix L12 Digital Camera this past summer and have had no problem until last night. My camera turned off and said "battery exhausted." After changing the batteries twice with new batteries, the lens would open for a second then close and the camera turned off once again saying "battery exhausted." I don't know what happened. Oh My Gosh. I have the same exact problem. My son just graduated high school and I missed half the pictures because of this. Way to captu


ITS NOT THE BATTERIES -- check out the internet (google "nikon coolpix battery exhausted" and you'll see hundreds of people are experiencing this glitch. best fix i've found so far: remove batteries and memory card, then replace batteries and t ... Nikon Coolpix L11 Digital Camera

Every time I turn the camera on it runs through it's warmup and then says please turn camera off and then on again. I do this and the same thing happens. When I turn it off it shuts down and then the lense retracts and comes back out before shutting down. Help!


... Panasonic Lumix DMC-FX7 Digital Camera

When i turn on my camera the lens trys to come out but then it gets stuck and goes back in; the screen says "turn the power off and on again" but when i do the same thing keeps happening over and over. The camera has one big rechargable battery so i can't just replace it. I've tried doing the reset, and I've tried tapping around the lens ad hitting the sides or bottom of the camera but nothing has worked.


Here is a very reasonably priced quote for repair; https://www.teleplancamerarepair.com/quote/cart.asp?iProbID=5&mo=358\0 ... Sony Cyber-Shot DSC-S40 Digital Camera

Camera problem when I turn the camera on the lens goes in and out and in and out thenthe screen says access then turn the power off and on again, battery ifcharged but when I turn it on again the same thing happens...I am inArgentina on holiday can you help?


Try new batteries anyway. There's always a chance that your existing batteries are no longer any good, even if they aren't very old. ... Sony Cyber-shot DSC-W50 Digital Camera

When I turn my camera on to take a picture, I get an error message that says "please turn camera on and off again". This happens everytime (even after turning on and off) so I can take a picture.


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic Lumix DMC-LZ2 Digital Camera

I have a sony cybershot wsc 1000 which when the camera is turned off the lens will not go back in.When turned on again the screen says Acess and then "turn the power off and on again" when i do this nothing happens and when switched on again it is exactly the same .the camera will not take pictures or show anything on the screen .It will playback old pictures.Any Clues?


Lens mechanism of your camera isn't working and you need to contact nearest Sony repair shop to fix camera properly. ... Digital Cameras

I tried to film on my camera but it keeps saying card error. now i can not see any of my pics or videos. it wont let me take pics or films either. when i turn on my camera it keeps saying crad error. before this happend it was saying the memory was full so i deleted some videos but now this has happened.


Buy a card reader and use it to download to your computer. Then, insert the card back in the camera, go into the menu and scroll to "format"...follow the on-screen instructions. ... Digital Cameras

I need some help to repair my Sony Cybershot DSC W50 camera. When you turn the camera on, it displays 'Access' for about 30 seconds, during which time the lens zooms in and out. Then it says 'Turn the power off and on again'. Nothing has happened to the camera - it has not been dropped and this fault just suddenly started. What can I do about this? I have had it just over a year. I’d be really grateful for any support! Thank you! Clare


When the camera is switched on it turns the lense out to a certain position and locks , but if due to any reason if the lense does not reaches to its proper position it retracts back and tries again 2 or 3 times, and then the movement haults and pr ... Digital Cameras

Battery Problem I bought a Nikon Coolpix L12 Digital Camera this past summer and have had no problem until last night. My camera turned off and said "battery exhausted." After changing the batteries twice with new batteries, the lens would open for a second then close and the camera turned off once again saying "battery exhausted." I don't know what happened.


I just had this problem today myself, and looked everywhere online for a solution. I changed the batteries (to Panasonic), and it didn't help. But i tried different batteries (Energizers) and the camera started working again. ... Nikon Coolpix 3200 Digital Camera

Zoom ERROR When I turn my Camera on it comes up saying Zoom Error. I can't Zoom in or out - and all I can see is a black screen. Last time I used it - I took a picture and put it bck in my bag - when I pulled it out again the error msg came up. It has happened once before and I reset the camera through the menu and the msg went away and the camera went bck to normal so when it happened again I press reset but this time it hasn't made a difference. Any suggestions?


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will have to get it fixed by a pro ... Fuji FinePix A820 Digital Camera

Memory Card I recently wiped all the pictures off my memory card and now when I turn the camera on it says 'card not initilised'Have looked through the set up menu and still don't no how to make it work!!!!Something happened when I was downloading some pics off my Fuji FinePix A330 digital camera where I wanted to only save some of the photos and delete the rest. Well I hadn't turned off the camera or unplugged it yet, so I guess somehow I deleted something labeled "fuji...". When I realized the


Have a look in the camera menu for the format or initialize card option, (sorry i cant be more specific - cant find the manual) this should initialize the card, else use a usb card reader to format the card in a card reader on your compu ... Fuji FinePix A330 Digital Camera

Put a 2GB card into the camera. It says error and It asks me if I want to format. I say yes. But then next time I turn the camera on the same thing happens! Can the camera take 2G?


... Vivitar ViviCam 3710 Digital Camera

When i turn the camera on, it cycles through opening the lens and zooming in and out but won't focus and then says "turn camera off and back on" but the same thing happens.


Sounds like there is some issue with the lens mechanism. Most probably something\015\012like a grain of sand fell into the cogs in the zoom mechanism (been\015\012taking pictures on a beach? ;). Dirt gets into the mechanism through\015\012the gaps be ... Panasonic Lumix DMC-TZ3 Digital Camera

My camera has brand new rechargeable batteries in it and it says charge batteries.. Then it wont' turn on or do anything and i know the batteries are charged up.. This is happening all the time. sometimes is will let me take 1 or 2 pictures. then i turn it off and will say charge batteries...


I had been having this problem for quite some time on my A1100 IS. It was incredibly frustrating! No matter how many times I changed the batteries I kept running into the same problem over and over.Somewhere I had read something about going into ... Canon PowerShot S2 IS Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3980 seconds