Having problems with your Panasonic Lumix DMC-TZ3 Digital Camera ?

Getting "turn off" message while in camera mode

\015 My panasonic tz3 will turn on and it's fine in playback mode. But when in camera mode, it won't focus then the screen says "turn camera off then turn back on again". When I turn it off then on again, it does the same thing. help!\015

Answers :

Fixing a Lens Error on a Digital Camera
\012
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Panasonic Lumix DMC-TZ3 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, I have a panasonic Lumix, DMC-FS5 digital camera. When I turn the camera on and it's on 'photograph' mode, a message keeps appearing after a couple of seconds saying: "please turn camera off and then on again". I get the same message everytime and am unable to take any photos or even access the menu options. There are no problems when the mode is set to 'playback' mode. The images are still there and I can scroll through, as well as access the menu.


Hi,I had this same problem. I have just pulled the lense (not with any major strength) when it was fully extended. This seems to have solved it for me!! ... Panasonic Lumix DMC-FS5 Digital Camera

Camera was on, working fine. When powering off, telescoping lens did not retract so lens remained extended just a bit with lens cover open. Waited a few minutes, turned it back on and I get the "access" display message then the beeps and (turn power off and back on) message. While off, I have removed the battery, replacing it with a fully charged spare and it still does this. The lens tries to telescope a little bit and retracts a touch, but I can't get the camera out of this mode. Can it be res


Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Sony Cyber-shot DSC-W55 Digital Camera

When I turn the camera on in either record or review mode I get a system error: zoom message after a few seconds and the camera is inoperable. Then when I turn the camera off the lens does not retract.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will have to get it fixed by ... Panasonic Lumix DMC-FZ28 Digital Camera

I too have the same problem with my DMC-FS15:- When I turn the camera on in either record or review mode, I get a system error: zoom message after a few seconds, and the camera is inoperable. Then when I turn the camera off, the lens does not retract. Is there updated software that can be downloaded and installed via the supplied USB cable, or any other fix? Regards Martin J


Well perhaps it is just the battery I wonder if this problem isn't simple a bad battery try a replacement, as sometimes they just go bad, and this is indeed a symptom of a battery not working properly. If you have an original power supply, then try i ... Panasonic Lumix DMC-FZ28 Digital Camera

Getting "turn off" message while in camera mode


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Panasonic Lumix DMC-TZ3 Digital Camera

Panasonic DMC-TZ4 When I switch on I get "Turn off camera and turn on again" message but it does not good. When I swtich off I get "workng hard" noises as if there is an effort to retract the lense but it will not retract unless I turn the camera on again. At that point the lense retracts and comes out again at once; more "hard work" noises and a new "turn your camera off" message. The only way to get the lense into the retrated position is to catych it at the right instant and remove the batter


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic DMC-TZ4 Digital Camera

Lumix tz3 Please turn camera off and then on again" as soon as camera is switched on. I Can view any menu, or read SD card, but cannot take any pictures. If I turn on in a picture taking mode it starts to focus and then the message appears, when I turn it off the lens does not close. If I turn on in playback mode, it works fine, if I turn it off from playback mode, then the lens closes. Basically, any picture taking mode triggers the error message. Solution?


Low battery maybe? Try holding camera firmly in one hand, with camera on and in record mode, and strike in on its edge firmly on the heal of your other hand. This technique is often sucessful with temporary camer 'quirks' like freezing, lens not full ... Panasonic Lumix DMC-TZ3 Digital Camera

When trying to download pictures from my Canon Power Shot A590, I get an error message saying the camera cannot be found. The software is ok (I can download from another identical camera). The camera is turned on (with fresh batteries) and the mode switch is set to "playback". What am I doing wrong.


Try NOT connecting your camera to your computer.The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or c ... Canon PowerShot A590 IS Digital Camera

Sony Cybershot DSC W90, when I turn the camera on I get a message that says to turn off and back on again. It will allow me to view photos already taken but will not turn on to take pictures. I hear the lens trying to go out into picture taking mode, but it does not open.


There are a number of solutions you can try,1.\015\012\015\012you will need to turn off the camera and hold the camera on the edges in a way that you wouild hold a pack of cards\015\012you ... Sony Digital Cameras

Optio E10 When I turn my camera on I get an error message that says "memory card error", I purchased a new memory card but still get the same error message...any suggestions? I have the exact same problem with my Pentax Optio S7. I turn on the camera and it displays the message Memory Card Error. I have tried several new cards and get the same message. There is an option on the menu to format a card, but you can't access the menu if you have the card installed. It takes great pictures without t


HelloOK, if the memory card itself is locked, you might \012sometimes get this error code. All you need to do is to take out the \012memory card and switch the lever on the left side to the unlock. ... Pentax Optio S7 Digital Camera

Everytime I connect and turn on my A600 via the USB the camera reads the message SELECT PRINTER AT PICTBRIDGE AT USB MODE SETTING WHEN PRINTING, and I cannot get any of the photo's from the camera onto the PC...... can anyone help??


Use a card reader to download your pictures to a folder you create on your desktop. ... Fuji FinePix A600 Digital Camera

Panasonic lumix DMC-FX01..zoom stopped working. When I try to zoom I get an error message to turn camera off and back on. This doesn't work. Camera still works fine in regular mode. Is the zoom fixable?


... Panasonic Lumix DMC-FX01 Digital Camera

My Sanyo VPC-E870 lens will not go back in. The camera will not turn on, except when I am in the playback mode. Periodically I will get an message that say lens error 21 and sometimes lens error 15. I have only had the camera since Christmas. Thank you for you consideration. Robert Castro


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Digital Cameras

When I turn on my Panasonic DMC-FX55 the lens comes out fine and the screen displays for 2 seconds then goes blank except for the message 'Turn off then on again' - which doesn't work. The only way to get the lens to retract is to select 'Playback' - tun off then on . The playback mode works fine and after 10 econds the lens returns to closed position. Is their a combination of buttons that reset the camera??


... Panasonic Lumix DMC-FX55K Digital Camera

Canon S2 when turning on in the shooting position...get message 'change battery'...rn when turning on in the 'view pictures' mode...camera works fine. Is the lens stuck?


WD-40 on a camera WOW ,,,,,ARE you ever lucky.. ... Canon PowerShot S2 IS Digital Camera

Missing pictures I recently went on a trip and took some pictures that disappeared from my camera. Later I started getting the message 'Card cannot be read' so I purchased another memory card. I was taking pictures when I get the message 'Card cannot be read'. I turned it off and back on and the missing pictures were there. I then get the message 'Out of memory'. I turn the camera off and back on and the missing pictures are gone again. WHERE ARE THEY???


Hey flowernthe,\015\012 The error message “card cannot be read" means there was and error when the camera tried to access the memory card. To fix this you should make sure you are using the right kind of memory ... Nikon Coolpix 4600 Digital Camera

I have a Nikon S6 digital camera, everything about the camera seems to work fine, except for this "lens error" message I keep getting. Sometimes I'll turn it on, and I can use it just fine. But then there are other times where I have to turn it off and on in order to get it to work. And then there are those times where turning it off and on don't help. I usually give up and try again later. Sometimes it'll still give that error message, and other times, it will just work like normal. What can


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Nikon COOLPIX S6 Digital Camera

Dropped approx. 3 feet onto carpet. Camera was on and lense extended. It would power up, get into capture mode and flash "sensitivity" and a green light LLC. After about 50 on & Off's the camera turns on but doesn't come out of playback. I have to open the battery compartment and close it then when I turn it on it will go into capture mode. When I take a picture it is washed out with lots of little vertical lines. Did the lense get knocked out of whack? Can I reset this? Any help will be ap


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Pentax Optio M20 Digital Camera

The CD that came with the camera will not load onto my computer. I need an instruction manual. I did figure out how to take, delete, ect. but for some reason the flash will not turn on and I get a message on the screen that says "macro mode".


The flash will not fire in macro mode because macro mode allows you to get close to your subject. Get out of macro mode by pressing a button with a picture of a flower on it or by it. ... Vivitar ViviCam 8025 Digital Camera

When ever I try to use the zoom button I get a message saying system error (zoom) I have also gotten a message that says Please turn off camera and turn on again... What is going on with my camera and what needs to happen to get it fixed!


When you first switch on the camera the lens will motor forward?\015\012\015\012If it does so then either the zoom control button is faulty or the control pcb \015\012\015\012If the lens does not move on first switch on then i ... Panasonic Lumix DMC-FZ28 Digital Camera

My Fuji s2000 always shoots picture that are blured. I have tried many settings and different exposures however I keep getting the same result. What can I do ? The worst mode on this camera is the auto mode, I can never get a clear indoor picture. This camera takes beautiful pictures of flowers/nature and all outdoor photo's turn out beautiful it is the indoor photo's I have even tried the sports mode for when people move but I still get a very blured image


Found the same thing and I think the answer is the opposite of previous suggestions. The s2000 is truly awful at anything above about 400ASA The degree of pixel binning it uses just makes the pictures look terrible. Force the camera to use 400 or s ... Fuji FinePix S2000hd Digital Camera

We bought our son a Vtech 1070 camera with mp3. However, when I copy music files to the camera or the sound card I've put in, I get the message music files not found! it appears to copy perfectly via internet explorer, and shows the files on the camera or on the card - but when i turn the camera on and try to access them, I get the same message both via the camera and the sound card. Help!


... Digital Cameras

I have just downloaded the camera on to iphoto and have cleared the camera memory . I clicked the eject icon on iphoto and once cleared unplugged the USB download cable . I have just pushed the power button to turn the camera on and firstly get the message on the camera screen "Access" then a message comes up saying "turn the power off then on again " When I do this the same process repeats itself . The lenses wont open and protrude out of the camera ready to take photos. The battery has ju


Sounds like you did two things wrong...you deleted/erased/or formatted the camera using the computer. You disconnected the camera without using the "safely remove hardware" function. ... Sony Cyber-shot DSC-W50 Digital Camera

I have an Olympus C-740 Ultra Zoom Digital Camera. I bought a new memory Card. This camera is new to me and this is the first memory card I have purchased. I do not have a manual for the camera. I am having a problem getting the camera to read the card. I insert the card, turn on camera & the window says "no picture". I changed the batteries also. I can get a oval ring which says "Info on the left, picture of cards at the top, "Mode Menu" on right, & bars at the bottom.It appears the "Mode Menu"


Choose YES for the Format option. Allow it to finish. Should work fine then.\015\012Possible defective card if does not work after full format. Do not use any "quick format" option.\015\012First time must be FULL format. ... Digital Cameras

I have a small Panasonic Lumix DMC-TZ5 camera. After fully charging the battery I am all of then sudden getting this error message :"please turn camera off and then on again." When the camer is OFF the lens is extended and open. When I move the camera to ON the lens moves in to the closed position closes, then reopens, extends, tries to focus, is unable to and the error message appears "Please turn camera off and then on again" This cycle just repeats. The lens is able to extend it is not st


Hi,Checkout this tip about digital camera error messagesLens Errorfix for Digital Cameraheatman101 ... Panasonic Lumix DMC-FZ7 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3768 seconds