Having problems with your Panasonic Lumix DMC-TZ3 Digital Camera ?

I have the same problem with my Lumix DMC-TZ3 lens error states "Turn off camera and then turn back on" Though my lens tries to adjust then stops. The power stays on with the error message. Til I turn it off .The lens still does not retract. Now when I turn it back on the lens will do the same thing. I don't think its the lens. How would someone repair or replace firmware. Can it be done over the net?


Answers :

Of course it's the lens. Try these:\012Fixing a Lens Error on a Digital Camera
\012
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Panasonic Lumix DMC-TZ3 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the same problem with my Lumix DMC-TZ3 lens error states "Turn off camera and then turn back on" Though my lens tries to adjust then stops. The power stays on with the error message. Til I turn it off .The lens still does not retract. Now when I turn it back on the lens will do the same thing. I don't think its the lens. How would someone repair or replace firmware. Can it be done over the net?


Of course it's the lens. Try these:\012Fixing a Lens Error on a Digital Camera\012\012This has to be THE most ... Panasonic Lumix DMC-TZ3 Digital Camera

Lens error When I turn the camera on it says "Lens error, restart camera," and turns itself off. When I turn it back on, the same problem occurs. The lens covers aren't completely closed, and the entire lens seems to be sticking out a little bit, like it didn't retract all the way. Please help! Thanks. Turn on the camera, camera shows a canon logo, then before turns off it said lens error, restart camera


\015\012\015\012I have a solution posted in doc "nikon s5 s6 lens cover error repair.doc"  uploaded on site http://www.esnips.com/web/papputatiyasStuff&n ... Digital Cameras

Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work. hi expert i m suffring in this error on my panasonic DMC-LC33 when i switched on


Try \015\012\015\012Klomtrix trick this worked with my camera\015\012thanks klomtrix ... Panasonic Lumix DMC-LC33 Digital Camera

Hi there, I have a Canon IXUS 90 IS - the lens is extended out and won't retract when pressing the 'on' button. The camera only makes a 'turning sound ' from the motor ( I asume the motor), but the actual display in the back reads' Lens error, restart camera' The nearest camera specialist for Canon are a good 600 and 1400 km's away respectively ( I live in Durban, South Africa)so would like to rather try fix this myself before paying, most likely a similar amount to buy a new camera. Any suggest


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Canon PowerShot SD790 IS/ IXUS 90 IS Digital Camera

Error message I have a panasonic DMC-LC33 digital. A system error message would show the minute I turned it on. The lens would come out. Then within 4 seconds the lens would go back in. I tried the on/off several time but the results were the same. I put the camera away for later. When I tried it the other day, it would not even turn on. The batteries are fully charged. Help!!!!!! I need my camera for my work.


*&%$@#%^&*&^% !!"It's working!!!!\015\012\015\012Turn your camera on and put it near your ear. Did you hear a softly motorized sound in the lenses area and the green LED is flashing? If you hear this sound do this.\015\012\015\012Do it under your own ... Panasonic Lumix DMC-LC33 Digital Camera

Lens error The lens on my Sanyo VPC-E760 will not close. I was not dropped, I was using it to take a picture and turned it off, but the lens never retracted. Now when I turn it back on, it is stuck in zoom mode and give an lens error message when I try to zoom back out, then it shuts itself off. Battery is fully charged. Any suggestions?


Hey jennbrady24,\015\012 What is most likely causing the lens error is that something is obstructing the movement of the lens (i.e. sand). I would first try removing the batteries and the memory card and waiting at le ... Digital Cameras

The first issue with my A1100 was that the lens would not retract fully when I turned it off. Then trying to "fiddle" with it the lens would not retract at all and I could not use the zoom with out the camera turning off and the note in the window states "lens error restart camera".I was however able to download a picture I took. Phil


This is a physical damage caused by a something being caught between the lens and the main body ...but I would not advice you to open it ..cause you may do more damage than good..try to see if there is anything in the way and visible ..and if after s ... Canon PowerShot A1100 IS Digital Camera

Lens error When I turn the camera on it says "Lens error, restart camera," and turns itself off. When I turn it back on, the same problem occurs. The lens covers aren't completely closed, and the entire lens seems to be sticking out a little bit, like it didn't retract all the way. Please help! Thanks.


Try the procedures in this tip. ... Canon PowerShot SD750 / IXUS 75 Digital Camera

Lens Error I recently had a problem with my Casio QV-R4... every time I'd turn it on, the lens would retract and I'd get a "LENS ERROR" message on the screen. I talked to customer support and they told me that Installing the new version of their firmware, v1.01 would fix this problem. I've since installed the new firmware version, but I am still receiving the lens error. Has anyone else encountered this problem? Does anyone know how to fix it? Please help!!!


As solutions 1 & 2 indicate, lubing the gears works!! This is a great camera, so I hope all of the QV-R4 owners try this. I may become a maintenance item for the camera.\015\012 \015\012I have a few a ... Casio QV-R4 Digital Camera

Is there any way I can get my camera back to normal! I turned it on and it said "focus error". When I shut it off to see if it would start over correctly it would not close the lens. I turned it on and the lens closed and then opened again and wouldn't focus. I turned it off and the lens won't shut. How weird is that? It obviously is capable of opening and closing but seems to be reversed and makes a funny noise when it can't shut at the right time. Can I wiggle or giggle something? I bo


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to g ... Digital Cameras

My canon camera Ixus 8515 has an error when turning on (after some 'stuck' noises) that reads 'lens error, restart camera'. The lens is not retracting. The camera has not been dropped. Was working fine one minute, then camera appeared out of focus the next. When I turned camera off then on again, error appeared. Lens won't go back in. Have not tried forcing it as yet.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you wi ... Canon Digital SD900 / IXUS 900 Ti Digital Camera

I have a cannon camera, my boyfriend dropped it with the lens extended and now whenever I try to turn it on I get a message saying that there is a lens error and the camera will shut down. I have tried a couple of answers on this website, but most have to do with a lens that is stuck out, mine will still retract back and forth if you smack it on your hand. My problem is when you power it off and back on the error shows up and the lens will not extend then. Any suggestions are greatly appreciate


... Canon PowerShot SD1300 IS IXUS 105 Digital Camera

I have a canon ixus 900Ti. I turned it on yesterday and the lens came out as normal. when i went to take a pic the camera shut off but the lense never retracted. when i turned the camera back on the splash screen came on, followed by a series of beeps and then and error message saying "lens error, restart camera". restarting has not solved the problem. its like the lens is stuck out. hope you can help Regards Liam


Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Digital Cameras

Lens Error My cameras battery was low but I kept taking pictures until the camera shut off by itself. The lens didn't retract all the way and now when I try to turn my camera on it makes a clicking noise like the lens wants to move but it doesn't and on the back screen it states a lens error. I am not sure how to resolve this problem I have charged the battery and taken it out. I unfortunately do not have the manual on me.


I have exactly the same problem with my camera, except there is no error message - just the screen is off (bat is full). i cant find a soultion anywhere in the manual or online. Any help on this would be much appreciated. ... Casio Exilim EX-S500 Digital Camera

Lens Error My lens will not retract with my camera. When I turn it on it cuts back off and says lens error. It sounds like the lens is stuck. please help me.


Hey Joy_2008,\015\012 A lens error usually means something is obstructing the movement of the lens (i.e. sand). You could try blowing compressed air into the side of the lens to try and dislodge whatever is stuck in t ... Casio Exilim EX-Z77 Digital Camera

Lens error I've had my camera for about 9 months and it's been working fine. 2 weeks ago I turned it on, went to take a photo and instead got this "Lens error" and the lens won't retract back in and the camera won't do anything. Sounds like this is a typical problem. Anything I can do to get my camera working again?


Try these procedures. ... Nikon Coolpix L11 Digital Camera

The lens on my sd600 won't open when I turn the camera to picture taking position. Screen goes black and message says ''lens error, restart camera''. I have to go back to view mode and then turn camera off and on again in order for partially opened lens to retract fully and close.


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Canon PowerShot SD600 Digital Camera

My Nikon Coolpix S203 has a "lens error". Every time I turn on the camera, then lens goes crazy, moving in and out and zooming in and out of focus, all the while making a beeping noise. It then retracts back into the camera and the message "Lens error." appears on the screen. Please, is there anything I can do to fix this? Thank you.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that yo ... Nikon Coolpix S203 Digital Camera

Lens is open and won't retreat back inside. I turn the power on and makes a funny clicking noise like its trying to retract the lens back in. After three seconds of this it says "lens error, restart camera". Its a canon powershot SD790 IS digital elph with image stabilizer. Canon PC1261...don't know if that helps.


I've had similar problems with various versions of this camera. Here's the fix, if all else fails. These are step-by-step instructions to take apart and fix the camera's lens error. http://johnsmouth.wordpress.com/2010/12/01/lens-error/ ... Canon PowerShot SD790 IS/ IXUS 90 IS Digital Camera

I have error code 0x1110000 the lens wont come out when camera turned on. Lens was out and would not go back in in may have been "helped" back in. Pentax Optio E60


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will have to get it fixed by a pro ... Pentax Optio E60 Digital Camera

Hello Everyone! I'm in Tokyo and when taking pictures this afternoon, and when I tried to turn off the camera the Lens didn't retract (I'm sorry if this is not the appropriate term it is not written in English, and English is not my mother tongue). And when I try to turn it back on, It says "Lens Error" in red. Can anyone please help me with this?? Such a bad time for this to happen....


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\ ... Nikon COOLPIX S710 Digital Camera

Hi I have a Panansonic Lumix - DMC-FS25. My camera has now developed a fault with the lens which won't go back in. When I turn it on the lens zooms all the way out and then back in again and a message appears saying - System Error (Zoom). Any help would be greatly appreciated, Many thanks Graham


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Panasonic Lumix DMC-FZ20 Digital Camera

It was dropped and now the lens will not retract. When turned on it only says lens error and then turns off. Oh, it trys to clos or open but nothing. I've taken the body off but not sure what the next step if any should be. Any solving direction would be fantabulous. An I thank in advance. Katies dad


The lens alignment have been lost when you dropped it down . So only it is throwing the LENS ERROR.Try adjusting the lens to its original position..Do not apply too must pressure to break it...We have to open the lens area and readjust it ... Nikon COOLPIX L20 Digital Camera

The lens will not retract on my PowerShot SX210is. Everything is completely frozen. When the power is turned on, the lens will not move and the screen says "lens error, restart your camera". But nothing will make the lens go back inside.


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Canon PowerShot SX20 IS Digital Camera

Focusing problems???? Yes my camera I have had for less not even close to a year and it is acting up on me now.For some reason when I turn it on sometimes the lens come out sometimes it doesn't then I have to turn it off and turn it back on not only that but everytime I turn it on it is telling me I have a focus error I have tried to everything I can being I lost my manual guide I can't do to much if you could help me figure out what is going on I would appreciate it. Thanks Sarah


Cleaning the lens worked well for me ... Fuji FinePix A500 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3612 seconds