Having problems with your Pentax Optio M50 Digital Camera ?

The camera powers on then shuts down almost immediately


Answers :

Fixing a Lens Error on a Digital Camera
\015\012
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Pentax Optio M50 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Olympus fe170 is about 2 years old. I had no probs till now. However, now when I want to download to PC (plugging in the USB cable), the camera powers on and almost immediately shuts off (screen goes blank). I have to remove & replace the batteries to go thru the same thing again. So just not able to download. Help !!!!


Try NOT connecting your camera to your computer.\012\012\012The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the c ... Olympus FE-170 Digital Camera

The camera powers on then shuts down almost immediately


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Pentax Optio M50 Digital Camera

When I power up the camera the lens opens and immediately retracts and the camera shuts off. I've attempted to push every button while turning on the camera to no avail. I also held onto the lens when it opened. Though the lens remained extended, the camera powered off. When I turned it back on the lens retracted and the camera powered off.


Have you made sure that the batteries are LiIon and fully charged? I had a similar problem with a Kodak Easyshare camera that required the higher voltage LiIon battery pack rather than alkaline AAs which will fit in there but is not exactly right. ... Kodak EASYSHARE M763 Digital Camera

I have a Pentax M20 camera. I love the camera but all of a sudden I find that when I turn the camera on, the camera almost instantly shuts off. I have new batteries in the camera. When the camera first starts up I can see "Green Mode" on the screen but it immediately shuts down. The camera is not allowing me to access any programming modes at all and certainly not allowing any picture taking. Until just a few days ago I have had absolutely no problems with this camera. Any advice is greatly appr


I am sorry you having that problem, and even more sorry I do not have a solution...On my Pentax Optio M10 batteries rechargeable or fresh alkaline only seem to last about 5-6 pictures before the camera deems them flat without charge and ... Pentax Optio M10 Digital Camera

I have a Kodak ZD 710. Using rechargeable NiMH. Was taking a photo of a shiny surface towards the sun in 86 degree weather. Took 2 good shots when suddenly camera shut off. I turned it back on but it shut off again. Turned it on again and screen wanted me to change date format and then immediately shut off again. Next it would not turn on at all, no power. I changed batteries. Still no power. Removed batteries and 4 Gb memory card for several hours. reinstalled but still no power. Today is


Is the lens still sticking out? It usually retracts when it turns off. let me know ... Digital Cameras

When the camera is turned on with the power button the lens comes out and stays out but the camera immediately shuts off and the lens stays open. The only time the camera remains on is when the dial at the top is in the position to view the pictures already on the camera.


Please try Power Resetting the Camera. To Power Reset the Camera, First, please turn OFF the Camera.Then, remove the battery pack from the Camera.Then, press and hold the POWER button on the Camera for 30 seconds.Then, reinser ... Sony Digital Cameras

Hi I have a Sony DSC-H2 Digital camera which i bought in 2005.I used it few times at special occations and i kept it safetly after removing the batteries.The batteries i was using was SOny Nickel Nh1 rechargable .But now even after recharging the camera is not starting .So i used another battery ,the camera did start but it just shut off almost immediately . I am getting worried .is there something wrong with the camera ?If so what might it be ? thanks


Some time battery connector a camera get oxidize please check it if it is clean it hope your problem will solve ... Sony Cyber-shot DSC-H2 Digital Camera

Hello, I have a Kodak easy share z1275 and has worked well for me for almost 3 years. Used it last week with no problems, has never given me any problems. Suddenly on Saturday, I turn it on to take a picture, lens begins to retract and the camera shuts off, it appears that there is a power supply probelm. I changed batteries, even though the ones I had in it were recently installed, but went ahead and put in new ones, and it will not power on. The blue power indicator light begins to come on


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Kodak EasyShare Z1275 Digital Camera

I was trying to put in my password and it would not take the password and the key keeps flashing to tell me the trail camera is still locked. Now I can not even get the trail camera to start when I push the power button. It comes up with the dashes and immediately shuts down. I don't understand any of these problems and how do we get this corrected?


See "forgot password" above. Bushnell has a serious problem on their hands if they want to continue selling these cameras.\015\012\015\012They need a PIN # for each camera. ... Bushnell Trail Sentry 11-9200 Digital Camera

My polaroid i1237 camera shuts off immediately when I power it on. It says the usual "Polaroid" on the screen and then sound 4 beeps and says "Goodbye" on the screen and shut itself off. I've taken out the batteries and replaced them, and the same with the SD card. Any clue if this is fixable?


I had the same problem with my camera it came on, it clicked, it said goodbye and that was it. what i did and it has worked since is apply gentle pressure to the lens and it's parameters. it took a few times of doing this between attempts at gettin ... Polaroid i1237 Digital Camera

THE LENS IS FROZEN OPEN THE CAMERA WILL POWER UP BUT POWER SHUTS BACK DOWN IMMEDIATELY


If the camera has recently been dropped you may have lens damage that's\015\012preventing it from powering up. If it hasn't been dropped your\015\012problem\015\012may be due to corrosion on the battery contacts inside the camera - which can\015\012p ... Kodak EasyShare M1033 Digital Camera

My camera indicates low battery, I replace with new batteries and turn the power on, the camera immediately shuts off


... Sony Cyber-Shot DSC-S500 Digital Camera

Camera shuts off almost immediately after I turn it on. I might get one picture taken and then it just shuts down. Sometimes I need to turn it off and on a couple of times just to be able to take a picture. I have 2 batteries and have charged both of them fully to make sure it wasn't a battery problem.


Also clean the battery terminals inside the camera, as well as on the batteries with a qtip and at least 90% isopropyl alcohol or a pencil eraser.\015\012Measure your battery to make sure it's holding a charge..\015\012Now to the other pr ... Olympus E-510 + 14-42 mm 1:3.5-5.6 Lens + 40-150mm 1:4.0-5.6 Lens Including Charger, Lithium battery Digital Camera

Powershot A640 Could Not Be Powered On, Burnt Smell My Powershot A640 died during a picture shot, lens remaining open. I thought it may be due to the dead batteries. But after putting new batteries and pushing the on/off button, the on/off indicator blinked once then shut off by itself. After a while, a strange smell came from camera batteries area, and I could feel warm there too. Immediately I took out all the batteries from camera. When checking the posts here the other day, I tried one


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Canon PowerShot A640 Digital Camera

Olympus u770 sw 7.1 No power, battery fully charged, lens cover is open. No lights no screen nothing. Camera has been perfect for almost 4 years just shut down whilst being used hence lens cover open. Any assistance appreciated. Thanks


HiSorry to hear about your issue with the Olympus mju 770 SW. There's a couple of things you can check and try, before ... Olympus Stylus 770 SW Digital Camera

My Easy-Share M1033 powers up on start-up, the screen lights up, then the camera shuts off immediately and the lens returns.


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that you will have to get it fixed by ... Kodak EasyShare M1033 Digital Camera

JVC Everio GZ-MG27U 20GB HDD Camcorder has a problem that it only will work with AC adapter plugged into the camcorder. I have two batteries, one has a full charge of 7.7vdc indicating a FULL charge, the other has almost no voltage indicating no charge. When I use the good battery, the unit starts up when powered on, then shortly shows a camera - - - - battery on display and then goes to "communication error" and shuts off. I found that the connection at rear of camcorder labeled as the " " volt


As far as i understood the problem \015\012\015\012you need to replace the old battery which is not charging, \015\012\015\012please dont use batteries of unequal charge in the camera operation. this will lead to problems from ... JVC Digital Cameras

After replacing AA batteries....camera attempts to power up,l but shuts down immediately....


Your problem may be due to defective batteries or corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing in ... Nikon COOLPIX L10 Digital Camera

Describe hi, i have a canon powershot a520 that was left in someone's purse when she gave it back to me the lens is now sticking half way out and when i push the power button it blinks on for a split second immediately shuts off. is there a simple fix for this or is it a major problem Canon PowerShot A520 Digital Camera Problem


Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Canon PowerShot A520 Digital Camera

Camera powers up and then immediately shuts back off. put new batteries in it and no change


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Digital Cameras

Lens error When I first power on my camera, it tells me to retry power on. When I do, it says lens error and shuts down. The lens will extend and then close before the power shuts off, however it does not close fully. The protective shutter on the lens doesn't close completely. I have tried removing the battery and letting the camera sit for awhile hoping that the camera will reset, however this has been of no help.


Maybe the lens is stuck. ... Casio Exilim Zoom EX-Z80 Digital Camera

Camera shuts off immediately after turning on.


Camera systems,lens unit,flash unit,mother boradetc,must be defective,so the camera get shuts off.ao take it to kodak service station ... Kodak EasyShare V1073 Digital Camera

Canon Powershot SD450 E18 problem: The camera lense would not open and reported error code E18 on power-up and then would shut down. I followed a procedure on the web for this issue and got the camera lens to open and it was working (able to take pictures for about a minute). When I powered down, the lense did not completely retract. I tried re-powering on but nothing happened. The camera is not getting any power. I figured the battery died so I re-charged it. I put the fully charged batt


... Canon Digital Cameras

Camera shuts down after shutter button is pressed. It shuts down halfway through the shutter operation. Everything else works fine-reviewing pictures, settings in menu, focusing, exposure settings etc. The camera focuses ok when the shutter button is half pressed then when you press the shutter button fully, the mirror goes up, shutter appears to open then the camera shuts down with no power. Only way to get mirror etc back to normal is to remove the battery and refit. When camera is turned b


... Canon EOS 40D Digital Camera

Camera dying? It will powerup like normal. But when a CF card (tried different ones)is in the camera and you press the button to take a photo, the screen will either shut off clean or give a flash of scrambled image then shut off and freeze. The only way to reset is to remove the batteries. It is also draining the batteries in the few attempts to power it on. When no card is in there it will stay 'alive' for a bit longer but pressing any button on it and the lense will power down leaving


CCD problem is the likely cause here and once you have another one put in camera should work fine. ... Konica Minolta DiMAGE S414 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4487 seconds