Having problems with your Samsung Digimax L830 Digital Camera ?
Focus is out and the lens should close when powered off but doesn't I changed the batteries to lithium was i to change the settings?
This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The camera when switched on displays in the top lcd display 'Err' yet shows battery as fully charged. ive reformatted my memory card via pc. changed the lithium cr 123a batteries for new ones. fully charged the 4 x AA batteries. the aperture ring lock is set to 22 on the 28mm-80mm af nikkor d lens. i have it set to af and auto but have tried all other camera setting i can access. it will focus no problem yet will not allow me to do anything else. i cannot access the menu eg func, play, in
Hi.Err means that the camera is in fault mode. There is no code, so that the fault is generic. This kind of error is often associated with shutter problems or other loens error. If you have a spare lens, remove battery and test the spare ... Fuji FinePix S1 Pro Digital Camera
Power Over the last few weeks I have had issues with the batteries. I found that the "Eveready" brand certainly doesnt work (I am currently in India and it is hard to find anything here!) and I just went through 3 sets of Duracells but after a short period of time it tells me to change the batteries. I just changed them with new Duracells but when I turn the camera on it wont let me get past that initial little birdy which is the start up screen. I also just noticed that my zoom lens thinger is
Get Rechargable batteries with charger of good company and try it. Your problem is discharged/ outdated batteries. ... Canon PowerShot A510 Digital Camera
Focus is out and the lens should close when powered off but doesn't I changed the batteries to lithium was i to change the settings?
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Samsung Digimax L830 Digital Camera
Hi. I have a problem with my Panasonic DMC LZ1. Has developed a fault. When powered on with charged batteries and memory card inserted, the camera doesnt do anything on any setting except the review (arrow indicator) setting. The review setting only works if you 'power on' on this setting. (You can see photos on the memory card). If you power on -on a different setting and move the dial to review, then review doesnt work either. Neither the display (except for review as above) or lens wor
... Panasonic Lumix DMC-LZ1 Digital Camera
White Screen Upon startup lens emerges but when screen appears it is white whereas it normally displays whatever the lens sees. When the shutter button is pressed the camera will focus and take a white picture which can be deleted. The camera does not flash although flash is set to automatic and photo taken in a dark room. Camera flashes (weakly) with flash set to manual on. Lens is unobstructed and appears to be perfectly normal. Camera was not dropped. Batteries have been changed.
\015\012Upon startup lens emerges but when screen appears it is white whereas it normally displays whatever the lens sees. When the shutter button is pressed the camera will focus and take a white pictur ... Pentax Optio E10 Digital Camera
I have a sony cybershot DSC-W210 and just recently the flash wont work when its on any mode to take a picture it has the flash symbol on the screen flashing and the code E:91:01 underneath also flashing its takin pictures as normal just without the flash it wont let me change the settings of the flash at all. Apart from this the camera lens shutter seems to be sticking when i turn on the camera it doesnt always open i have tried cleaning the lens but it doesnt seem to make any difference!
I have a sony cybershot DSC-W210 and just recently the flash wont work when its on any mode to take a picture it has the flash symbol on the screen flashing and the code E:91:01 underneath also flashing its takin pictures as normal just without the f ... Sony Cyber-shot DSC-W70 Digital Camera
Coolpix 3100. I changed t batteries recently and since then when I try to take pictures lens closes in and camera switches off. I changed settings but to no avail. I have used same cheaper batteries before and they work a treat. It took a couple
Try some new batteries not cheap ones, if still you have the same issue try to factory reset it, if you will need more help with your camera download a factory service manual from the below link: ... Digital Cameras
My Canon S2IS has served me perfectly for over five years. All of a sudden it is going through a set of new batteries in half an hour. A few pictures and short video clips after installing brand new Duracells I was getting the low battery warning and then a few more minutes of same it was dead, showing the change batteries message. Any ideas or is it time to retire this baby? Also, when I power up the camera, the lens makes a grinding noise while it is extending. What's up with that? Could it
Are you new batteries are NI-MH ones?\015\012Canon canon's low vote detection setting is low, and you'd better use Li-ion Canon Camera batteries. ... Canon PowerShot S2 IS Digital Camera
My camera displays E18 on the lower left hand corner no other operation I turned the camera on the lens deployed and it intitiated OK but I can hear some activity such as motor etc. but after 10-20 sec it dipslays E18. I can view pictures, set up the camera but the moment I try to activate the caera function it goes into this routine. The lens now is stuck in the deployed position. I removed the batteries (Energizer Lithium), checked them they are good?
... Canon PowerShot S2 IS Digital Camera
Frozen Lens I just dropped poor camera on to the carpet from about a foot! Everything seems to work except the shooting mode, the lens wont extend from the actual camera. The slider still goes across fully and the battery is in fine. I can go into quick view mode and still change settings etc. Is this likely to be expensive to fix?
I initially went back to the manufacturer - Olympus at firstname.lastname@example.org found on the website ... Olympus MJU 400 Digital Camera
Coolpix P60 - had it hooked to tv to view photos - was working fine. Unhooked it and now the lens stays out - it retracts when you hit the on/off button, but the lens always pops out again. Cannot view anything (viewfinder and screen are both blank except for camera settings). Have changed batteries, put in a different memory card - nothing seems to work..
Hi,\015\012\015\012Please try to hook up at TV again and see if still functioning there. Then press || to alternate between displays.\015\012\015\012It hope it will work.\015\012\015\012Cheers! ... Nikon COOLPIX P60 Digital Camera
Even when I change the batteries, when i tried to put on the camera by sliding the front lens cover, the usual display comes in the screen, stay for one or two secs. then went off. I can not take a photo, even i am not been able to see the stored photos. I replace the batteries with new set severel times but the problem remains.
I have the exact same problem. If you hold down your flash button as it powers on, you can run some diagnostics although with mine, it showed the CCD is not functioning. Pretty much that means you now own a paperweight. ... HP Photosmart M22 Digital Camera
I have a Canon T1i Rebel. My aperture is frozen in manual mode. Works fine in AV mode. I have checked it out on 3 lenses. The camera knows I have changed the lens, I have taken the battery out all night, I have reset the camera back to default settings too...
Not knowing your experience level, I want to make sure that you are (in the Manual mode) attempting to change the aperture by holding the aperture button with your thumb while rotating the main dial to increase or decrease the aperture value. If you ... Canon EOS 500D / Digital Rebel T1i Digital Camera
Black screen Hi, I have Nikon coolpix S1 camera. Till last month, I was able to take pictures, but today, when I tried to take one, it showed black screen. The lens opens properly. I am able to see the images which were captured earlier, but, now, I am unable to capture any image because, everything is seen black. I reset all the settings, charged the battery fully, but no change.
Click here to read the web page for solution. It's free to fix. You need to scroll down the page, as it has many re ... Nikon Coolpix S1 Digital Camera
The view finder or screen are black. The lens moves out when the camera is powered on, I can hear the shutter click when pushed; the telephoto is moving; I have all the settings show on the screen when the camera is powered on but I cannot see anything through the view finder or on the screen and no image is captured when a pic is taken. I changed the batteries and it made no difference.
I know it may sound like the shutter is moving, but you're going to have to actually look down the lens barrel to confirm it's actually moving, and not just producing a sound effect from the camera. Also keep in mind Canon's SX IS series cameras are ... Canon PowerShot S3 IS Digital Camera
Frozen Camera I have a Panasonic Lumix TZ3 digital camera. The last time it worked, the screen went checkered, so i turned it off. But upon turning it off, the lens of the camera stayed out like it was taking a picture. Now it won't turn on. I've tried recharging the battery, changing memory cards, no memory card, switching settings and turning the on/off switch. Is there anything to be done or I do I just need to get a new camera?
Try letting it drop about 4 tto 6 inches on a hard service covered by a paper towel. Don't let it land on lens of course. You can remove the mem card. It has 13Meg of internal. ... Panasonic Lumix DMC-TZ3 Digital Camera
Date and time setting dont save, I changed the CR 1220 battery. Still doesnt save. Every time I turn on the camera the date / time setup appears.
In another forum I found a solution: \015\012\015\012Remove the watch battery from the cameraCarefully bend the contacts inside the camera toward the opening that the battery fits into. - I used a heavy safety pin to bend the contac ... Canon PowerShot S5 IS Digital Camera
Autofocus problem I dont really know how to explain my problem.. I got a Nikon D40 for Christmas last year and last week we went on vacation. The camera was working fine. but suddenly the camera wouldn't auto focus. Everything is set on auto.. I only have the lens that came with the camera. The battery is charged.. it doesnt even make a noise like its trying to focus. the wiewfinder bracket thingy lights up red but nothing after that. I am new to photography so I know I probably sound like
You have to hold the shutter\015\012down halfway as you compose the first shot so the AF system can focus\015\012and lock, and then the camera fires instantaneously when you press the\015\012shutter the rest of the way. ... Nikon D40x Digital Camera
Have a Nikon CoolpixS700. Worked great until just recently. Not damaged. Now there are vertical disortion lines in the images. Tried changing settings, reformat card, remove battery, clean lens, etc
... Nikon COOLPIX S700 Digital Camera
I have had my S9600 for 4 years, for most of that time, when i changed the batteries, all my settings remained the same. Now, when i change the batteries, every setting has returned to factory standard (stupid beeps and whirring noises, no date etc) and i have to reset everything. The user manual has no mention of an internal battery, but i figure there must be one and it now needs replacing. How do I do this?
My camera has refused to power up despite fresh batteries - I have had no response. I left it overnight as suggested in the manual - but still nothing. It hasn't been used for a few months and was left without batteries for fear of leaking. Any ideas ... Fuji Finepix S9600 Digital Camera
Change Batteries....? Hi there, I have owned the Canon A 95 for almost 2 years now. Since a couple of weeks back its not been working at all. It keeps saying "Change Batteries" even after i put in a new set of batteries. After a few seconds of turning it on, it says Change Batteries and shuts off. Triedputting in new batteris a few times but still no luck. Any help would be highly appreciated!
Ok.. did you guys try a reset? Just remove the batteries, wait for 60 seconds then put them back in.. that should reset the camera.. ... Canon PowerShot A95 Digital Camera
My cannon A570 was working fine. Then all of a sudden it would turn on and turn off right away so I changed the batteries. This did not help. The lens was opening very slowly. Then it wouldn't open again. I received a change battery message which was odd but changed the batteries again. (they were pretty hot) Once I changed them it worked again for a second but now it wont turn on. Any suggestions?
... Canon PowerShot SX100 IS Digital Camera
Every time I change the battery on the coolpix 995 I have to reset date and time and all other settings. I never had to do this with my 990. How do I keep all settings , including film quality , unchanged during battery change?
Your problem is that your camera actually has two batteries. There's the obvious user-accessible one but there's also a tiny rechargeable one hidden inside the camera which recharges from the main battery. The smaller battery is designed to provide h ... Nikon Coolpix 995 Digital Camera
Camera lens My camera lens is out and will not go in and when i change batteries it want do anything. When i change batteries it makes a popping noise and want do anything
The lens motor drive has stalled seemingly due probably to a knock whilst out - they are very fragile and prone to this.Only a return to makers for repair or replacement is an answer. ... Samsung Digimax S630 Digital Camera
I changed the batteries in my S2IS powershot to the re-chargeable canon NiMH and purchased a second set of energizer NiMH batteries. When we changed to the new ones, neither set works! The camera won't turn on.
Use enolop batt white color ... Canon PowerShot S2 IS Digital Camera