Having problems with your Samsung Digimax S800 Digital Camera ?

Telescopic mechanism for lens has jammed flush with the camera body. camera beebs when powered up and shuts down again.


Answers :

Fixing a Lens Error on a Digital Camera
\012
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
I have this problem to Could you please email me if you found a solution thankyou
\015\012
\015\[email protected]
Repair Help & Product Troubleshooting for Samsung Digimax S800 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Telescopic mechanism for lens has jammed flush with the camera body. camera beebs when powered up and shuts down again.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Samsung Digimax S800 Digital Camera

The battery ran out and I was not able to recharge for a couple of days .The camera never shut down the lens still stayed out of camera body even when the battery was taken out. After recharging battery and reinserting it in the camera the camera will not function. When the power button is pushed the light goes on and the camera makes attempts to close lens but then it buzzes and makes beeping sounds and then goes off.


Hi,Unfortunately, this is a common problem on this model. Yet, no resolution other than getting it repaired.There are a number of things you can try:1. Ensure batteries are fully charged2. Look ca ... Olympus FE-200 Digital Camera

Lens error When I first power on my camera, it tells me to retry power on. When I do, it says lens error and shuts down. The lens will extend and then close before the power shuts off, however it does not close fully. The protective shutter on the lens doesn't close completely. I have tried removing the battery and letting the camera sit for awhile hoping that the camera will reset, however this has been of no help.


Maybe the lens is stuck. ... Casio Exilim Zoom EX-Z80 Digital Camera

When I power up the camera the lens opens and immediately retracts and the camera shuts off. I've attempted to push every button while turning on the camera to no avail. I also held onto the lens when it opened. Though the lens remained extended, the camera powered off. When I turned it back on the lens retracted and the camera powered off.


Have you made sure that the batteries are LiIon and fully charged? I had a similar problem with a Kodak Easyshare camera that required the higher voltage LiIon battery pack rather than alkaline AAs which will fit in there but is not exactly right. ... Kodak EASYSHARE M763 Digital Camera

Camera was on, working fine. When powering off, telescoping lens did not retract so lens remained extended just a bit with lens cover open. Waited a few minutes, turned it back on and I get the "access" display message then the beeps and (turn power off and back on) message. While off, I have removed the battery, replacing it with a fully charged spare and it still does this. The lens tries to telescope a little bit and retracts a touch, but I can't get the camera out of this mode. Can it be res


Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Sony Cyber-shot DSC-W55 Digital Camera

Lens error when trying to power on camera. no dirt in lens. lens extends buzzes retracts and turns and then repeats before fully retracting. Can see camera focusing while cycling and retracting. lens error appears on screen at end of cycle. tried tapping camera and lens body to dislodge dirt as well as compressed air on lens body without success. any ideas?


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Nikon Coolpix S210 Digital Camera

Toshiba PDR-M700 When I power up the camera, the lens will not come out and sometimes will come out all the way to maximum zoom. When I power off with the lens out, it clicks as if something is stripped or loose. After shut down, I can push the lens back in. Once in a while the camera will work but eventually the "Lens Error" message comes up. This was a good expensive camera when I bought it but taking it in for service would probably cost more than the price of a new camera today. Can you sugg


It sounds as though the drive gear is slipping... If you give up on trying to repair your camera I may want to purchase it for parts (my sister-in-law broke my LCD display)[email protected] ... Toshiba PDR-M700 Digital Camera

My Panasonic Lumix DMC FS3 is not powering on fully.... When I switch the camera to the on position the green light blinks on and then off and the lens opens but the screen doesnt seem to power on. When I shut the camera in the OFF position, the green light blinks on then off and the lens retracts back into the OFF position. Can I trouble shoot this or do I have to take to a repair shop? Is this camera even worth getting repaired


See if the memory card cover had been open in that moment .However if the problem persist the camera must go to the repair shop. The syscom and associates circuit has faulty .God bless you ... Digital Cameras

I can only turn on my Cybershot DSC-N2 while the camera is in playback mode. I can look at the pictures and videos and change settings with no problem.. but when I try to switch to camera or video record mode the camera turns off by itself. Sometimes the lens will come out and then the camera powers down with the lens stuck out. Other times it just shuts off before the lens even has a chance to come out. The camera has never been dropped or damaged.


First press power button for 15 seconds .Then remove memory card from it may be your memory card has some issue.also press reeset button on camera some camera has reset button.start your camera without memory card. ... Digital Cameras

Canon Powershot SD450 E18 problem: The camera lense would not open and reported error code E18 on power-up and then would shut down. I followed a procedure on the web for this issue and got the camera lens to open and it was working (able to take pictures for about a minute). When I powered down, the lense did not completely retract. I tried re-powering on but nothing happened. The camera is not getting any power. I figured the battery died so I re-charged it. I put the fully charged batt


... Canon Digital Cameras

Lens error Lens is fully retracted. At power on there is motor noise and clicking but the lens does not extend. Screen reports "lens error" and the camera shuts down. Can the camera be partially dismantled to release the lens or is this a full repair job?


Try the procedures in this tip before taking the camera in for repairs. ... Canon PowerShot S95 Digital Camera

I have a cannon camera, my boyfriend dropped it with the lens extended and now whenever I try to turn it on I get a message saying that there is a lens error and the camera will shut down. I have tried a couple of answers on this website, but most have to do with a lens that is stuck out, mine will still retract back and forth if you smack it on your hand. My problem is when you power it off and back on the error shows up and the lens will not extend then. Any suggestions are greatly appreciate


... Canon PowerShot SD1300 IS IXUS 105 Digital Camera

When i press the power button to turn on the camera, the lens does not come out as it should - I get a "Lens Error - will shut down automatically - restart camera" appear on the screen - My Camera is the PowerShot SD1400 IS Digital ELPH - I have only had this camera for a few months


See Lens Error ... Canon PowerShot SD1400 IS IXUS 130 Digital Camera

My camera was dropped in the sand awhile ago. I blew some air in it, and got it to work. After about 2 weeks I was able to start the camera but then it shut off on its own and now the silver lens part won't go back in. I have tried everything to get it shut again. And still nothing. When I press the power button, it clicks twice and then it beeps three times. Can you help me with this, when I bought the camera, there was no warranty offered. This is the 3 Samsung camera that has broke in the pas


HelloThe problem is that the lens has become stuck in the barrel\012 after the sand particles have jammed it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Samsung BL103 Digital Camera

When the camera is turned on with the power button the lens comes out and stays out but the camera immediately shuts off and the lens stays open. The only time the camera remains on is when the dial at the top is in the position to view the pictures already on the camera.


Please try Power Resetting the Camera. To Power Reset the Camera, First, please turn OFF the Camera.Then, remove the battery pack from the Camera.Then, press and hold the POWER button on the Camera for 30 seconds.Then, reinser ... Sony Digital Cameras

When I turn the camera on, the lens extends, makes a few noises like it is trying to retract the lens. The viewer shows nothing - like the lens cover is on. When I push the power button to shut it off, it makes the noises again and shuts off but does not retract the lens. The battery is fully charged.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Olympus FE-220 Digital Camera

I have a Ploaroid iS2132 digital Camera. Every time I try and take a picture the screen goes black and the camera shuts off with the lens extended. I have to cycle the power button to get is to powe


... Polaroid I Digital Cameras

DSC-P73 problem Hi, when I turn on the camera, it drives the lens out then shuts off, leaving the lens out. If I try a couple of times with the power button it will eventually draw the lens back, displaying the word "Access" then shuts off. I have replaced the batteries... no difference. Any clues please? Rob from Australia


In this case i think theres a lens error so i would request u to contact the nearest technician because i think the camera is defective ... Sony Cyber-Shot DSC-P73 Digital Camera

EX-S500: * I turn it on and the 'Adjust' screen comes up. *I press the 'Menu' and the lens comes out, the green light flashes for awhile, it beeps a few times, it grinds a few times and shuts off. The lens stays out. *I turn it back on, the lens goes back in and the 'Adjust' screen comes on. * I press the power button and the camera goes off. *I left the camera in the charge gradle all night and the battery did not charge. *Help


You could have a power and lens issue, going on at the same time here. There's a couple of web blogs that delineate things you can try to correct these issues, and here they are:\015\012 ... Casio Exilim EX-S500 Digital Camera

The camera won't turn on. When the power is turned on, the camera lens pops in and out 2 or 3 times before shutting down permanently. The power light does flicker, but the camera is rendered useless. Why??


I charged the battery 3 times, with no results. Then I banged the **** out of it on the counter top. It seemed to work after that! ...? ... Olympus Digital Cameras

Canon SD4000 camera, when hitting the power button, the screen remains black screen, the green light blinks twice, lens zooms out, shutter opens. Screen remains black, and I do not seem to have any control at all; pressing the zoom button doesn't move lens, no notable reaction to anything. Hit the power button again, the lens zooms back into it's original position, shutter closes (occasionally does not shut completely), green light blinks twice, screen remains black. Tried turning on w/o SD card


... Canon SD4000 IS IXUS 300 HS Digital Camera

The camera was dropped while the lens was open. The camera now only opens about half an inch out and then shuts on itself. When it shuts it powers down and will not stay on. I am assuming that the motor is the problem, if so is it fixable? How would I fix it? How much would that cost?


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Kodak EasyShare V1073 Digital Camera

I've canon power shot SX120 IS, when press on/off Button the camera shut ot but lens didn't come in. the lcd says "lens error, restart the camera"


Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. O ... Canon PowerShot SX100 IS Digital Camera

I have this camera and the lens is locked open. When I put new batteries in it, I hit the power button and it will come on, if I touch anything...the camera does a loud 3 beep then shuts off. Lens still open. Is it hopeless?


Try removing the memory card if you have one and see if that make a difference. Some cameras and cards do not get along.If still same thing, try removing the batteries, press and hold power button for 5 full slow seconds, wait 10 minutes, ... Samsung Digimax S500 Digital Camera

Powers off my canon powershot sd600 digital camera keeps powering off after about 30 seconds. I have gotten a new battery and that didn't help. On the left hand side before it shuts down it has the letter and numbers E18 on the bottom. The zoom lens is also sticking out and will not retract. There are no error messages on the camera at all. If anyone has a solution please let me know. Thanks!


E18 is a lens error message, the lens is stuck or bent, and wouldn't come out, that's why camera shuts off after it tries to do so at the start, not much you can do, but replace the whole lens assembly ... Canon PowerShot SD600 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5395 seconds