Having problems with your Sony Cyber-shot DSC-S600 Digital Camera ?

I can turn my camera on the lense comes out and goes right back in what could be the problem?

Answers :

Fixing a Lens Error on a Digital Camera
\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Sony Cyber-shot DSC-S600 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I can turn my camera on the lense comes out and goes right back in what could be the problem?

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Sony Cyber-shot DSC-S600 Digital Camera

Canon 1000D Hello there, I'm in China at the Beijing games. my 1000D is giving me a error message 99. can't take picture. I have turn it off and on, take the battery out but the problem still come back after 4 or 5 snaps. please help. I have change lenses and clear the head but not winning. Thanx well i have the similar problem, that i could identify that the camera goes off state after 30 mins, then i found that the display power cannot come, but the camera is working with view finder, if i

Yep set the auto turn off higher and instead of removing the battery, just open and close the battery compartment.This appears to be a problem I have raised with Canon, hopefully they will release a firmware update soon to fix this ... Canon EOS Digital Rebel XS / 1000D IS Digital Camera

When i turn on my camera, the lense comes out, fluxuates in and out, beeps and goes back inside the camera sutting off. Sometimes the shutter sticks and will not close comepletely? Will dut or grit make the shutter do this? How do i fix it? .......Same problem with mine,I can only use the playback mode when I press the on/off & > button simultaneously. Could this be a manufacturers fault? My camera is over 2 years old, so has no warranty

Try the procedures in this tip. ... Pentax Optio M20 Digital Camera

Lense problem When i turn the camera on in picture taking mode the lense does not come out all the way and if i push it again it still does not come out and then when i push the power button a third time it closes the little bit it opened... but not all the way. However if the camera is in play mode and i turn it on, the lense comes out all the way just fine... then goes back in on its own and i can view the pictures. Because of this it appears the mechanism is working fine but there is maybe

Dear jmgrev,\015\012\015\012Whenever you turn your camera on and your lens doesn't go in and out properly you are likely experiencing a lens error of some sort. Look for an error 18 or a "lens error restart camera" message. If either of t ... Canon PowerShot SD630 Digital ELPH / IXUS 65 Digital Camera

When I turn the camera on, the lenses comes comes out but then goes right back in. The screen comes on for just a second, but then turns off when the lense retracts. The camera is a Kodak MX1063. Help!

This could be a lens issue or power issue. Here are two websites that delineate what you can try to fix the problem:\015\012 ... Kodak MX1063 Digital Camera

My camera turns on and then right back off. wen u press the power bottom the screen comes on and shows the Kodak label like its turning on and the lense begins to open but immideatly closes and the camera turns back off. i charged my camera all night but the problem persisted. the only thing i can think of is tht the day this happened i took my camera with me to the beach and it was warm but not extremely hot.

I had the same problem. This is how I fixed mine! Turn on camera grab the lens with two fingers before it can re-tract back into the camera and shut it self down. Use compressed air around the lens housing no more the 80 PSI. Hopefully t ... Kodak EASYSHARE M1063 Digital Camera

Only about 9 months after buying my camera, It wouldn't turn on. I'll plug it in and the light will come on that it's charging, but when I got to turn it on, it turns on for a split second (and the zoom lense comes out) and then it turns itself right back off (and the zoom lense goes in). I thought that it needed a new battery so I bought one and it's still doing the same thing. I emailed Kodak and they said that I should just send it into them for a $60 repair fee...lame. Any suggestions?

If its only been 9 months since you bought it shouldn't it be covered for repair? espically if its a manufactures fault,which it sounds like. ... Kodak EasyShare M863 Digital Camera

I have an olympus digital camera fe-170. when i turn on my camera, the lense come out and the LCD screen is black, when i try to turn it off, it doesnt turn off, but after like 10 seconds it turns off by itself. but when it turns off the lense dont go back in?! then when i try to turn it on, its the same thing. when i plug it into the computer, the lense go back in, but when i unplug it from the computer and try to turn it back on again...SAME PROBLEM. i did drop it before, but can i do anything

The lens is bad, needs to be replaced. Maybe purchase camera on ebay with broken LCD but good lens. Replacement can be time extensive. Will need #00 or #000 phillips screwdriver and solder iron. Remove 6 exterior screws+2 inside battery door. Take of ... Olympus FE-170 Digital Camera

My camm! I have an olympus digital camera fe-170. when i turn on my camera, the lense come out and the LCD screen is black, when i try to turn it off, it doesnt turn off, but after like 10 seconds it turns off by itself. but when it turns off the lense dont go back in?! then when i try to turn it on, its the same thing. when i plug it into the computer, the lense go back in, but when i unplug it from the computer and try to turn it back on again...SAME PROBLEM. i did drop it before, but can i do

I think thy will say you, replace lens unit. but lens is very expensive, so we can buy new one camera. I have the same problem, i found focusing lens wheel teeth slipping, no parts available, so i covered a gum coat on the teeth. ... Olympus FE-170 Digital Camera

The battery is fully charged, when I turn the camera on the lense will come out lights on the camera come on for a second then everything goes off,lense goes back in.If I take the battery out for a minute then put it back in it lets me set the date then shuts off.

Your problem may be due to weak/worn out batteries or corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: r ... Digital Cameras

When i turn the camera on, it immediately shuts down after showing the picture on the screen for about one second. The lense first comes out and then rapidly goes back to the case of the camera. What is the problem here?

Low battery ... Casio Exilim EX-S600 Digital Camera

I turn it on and the lense comes out and then goes right back in and turns off. I'm in Thailand and need my camera to document my year abroad! I thought it was not charged so I charged it and it still does the same thing.

Hi! You may have a faulty battery. If the battery is faulty it may indicate that it's fully charged but the truth is it doesn't have enough power for the camera's operation which can cause the lense to come back in. Have the battery replaced and you' ... Digital Cameras

Power doesn't work properly. When I turn off camera with power button, lense stays out. When I turn on, the lense goes in then back out again, but after a few seconds, I get the message: "Please turn camera off then on again." If I don't do anything, the camera will turn off by itself, and the lense will go in. Battery is fully charged, and nothing dramatic happened to start this problem...

HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\ ... Panasonic Lumix DMC-FX8 Digital Camera

Fe-280 Hello. my camera is a FE-280 and when i go to turn it on the lens comes out then goes back in about 4 or 5 times then the light flickers and then shuts off anything you know that i could do to fix that problem or take it someone or something?

I have recently had the same problem. I sent my camera back to Olympus who very efficiently repaired it FOC and sent it back with an extended warranty. I gather this is a very common problem with this camera. ... Olympus FE-280 Digital Camera

Camera lense/power Camera lense is stuck out. When I turn it on the lense goes in and then comes out, a main picture apears, green light comes on and then it powers off with the lense stuck out. It will only stay on if I have it in play back mode. Please help! Phil D. PS - I have the PowerShot SD400

The following blog outlines some repair options for a lens error. They won't work for all cases, but they're worth a try if the camera's no longer under warranty:\015\012\015\012 ... Canon PowerShot A510 Digital Camera

Olympus SP- 550 UZ , Model number Sp -550 UZ, L 08208054 UO 18x optical zoom - 28mm wide, Digital Camera DC 6V As soon as the power button is pressed, the screen lights up the lens comes out with a message "Zoom Error" and the lens immediately goes back into the camera. I can also hear light clicking sound as the lens goes back into the camera. This problem has been going on occasionally and then I could see the object to be photographed. Now for the last few days I am unable to take any pictur

... Olympus SP-550 UZ Digital Camera

Same Problem When I hit the power button, it flashes, the HP logo comes up on the screen the lense retracts and comes back out and the power goes off. That's all it will do. Other times when I turn it on, a little yellow light on the bottom left side in the back flashes once after the blue power light flashes three times and then turns back off. Arggggghhh!

Use never used batries i have the camra it work s better with new batries ... HP Photosmart M525 Digital Camera

Lense will not stay out. When you turn the camera on the lense comes oot then goes straight back in and camera turns off. The battery is fully charged.

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Pentax Optio M60 Digital Camera

When i turn on my camera it turns right back off. the lens will come out as if it is about to take a pic but then it goes right back in. whats the prob?? it stayed on for about 10mins a while ago but it is messing up again. plz help

This is most likely to be a battery or battery contact problem. Are the batteries fully charged? If so I would suggest that you remove the battery - check and clean the contacts - replace and check if this resolves the problem.\015\012\01 ... Sanyo VPC-E7 Digital Camera

When i turn on my camera it turns right back off. The lens will come out as if it is about to take a pic but then it goes right back in. I cleaned the original battery and connections, still didn't work. I got a new battery and it is still doing the same thing, from the 1st time I put the new battery in.

Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Sanyo VPC-E7 Digital Camera

My sony cyber-shot 7.2 mega pixels digital camera is NOT working. When i turn it on, it says acess, then the lense comes out and goes back in over and over. After doning that about four times it says "Please turn camera off and then back on again" However when i do this, it just repeats itself. Any idea of what i should do?

... Sony Cyber-Shot DSC-S40 Digital Camera

I purchased a Sony Mavica cd250 camera in Nov 2002. I had no problems with it until about 4 years ago. I purchased a new battery, and all was fine. Until recently, I had not used my camera for several months. I could not get the camera to hold a charge (after it was plugged in and charged, I could unplug it and it would stay on for a few minutes. When I turned it off, it would not come back on). I tried purchasing another battery from Battery Outfitters, but the battery they sold me was not comp

The battery is definitely your chief suspect. It's nearly 8 years old so is well overdue for replacement. ... Sony Mavica MVC-CD250 Digital Camera

Broken camera My daughter has a FE 140 Olympus Digital Camera. We have had some problems. When you turn it on it beeps, the red light flashes, and the lenses goes in and out. The same thing happens when we try to download pictures, except that the camera will shut off, leaving the lense out. Do you have any idea what could be wrong?

In addition to the one year World Wide Warranty,\015\012issued by Olympus Corporation in Japan, the European warranty, issued by Olympus Imaging Europa GmbH, is\015\012valid for two years from the date of purchase, if purchased after 1st ... Olympus FE-140 Digital Camera

I just set the date stamp in the on position. Then, turned the camera off as I didn't need to take a picture. Now, when I turn it on, the lense comes out and then immediately goes back in flush and the camera is in the off position. The battery is fully charged and the camera even does this when I have it on the charger.

Hi,How long have you owned the camera? If under a year then I would recommend having it serviced by kodak under warranty. If it's over a year old you may want to try a new battery otherwise consider replacement.Thank you,Lee ... Kodak EasyShare V1003 Digital Camera

When i turn the camera on the lens comes out for a second then goes back in and it turns itself off, there are new batteries in the camera, what is the problem?

Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digital camer ... Sanyo VPC-S880 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5822 seconds