Having problems with your Sony Cyber-shot DSC-W110 Digital Camera ?

When power is turned on the lens opens and then shuts repeatedly until telling me to turn off the power and start again but doing this just causes it to do the same thing. How can I get it to open an operate properly. The battery is fine as I can view existing photos etc. on the screen.


Answers :

Fixing a Lens Error on a Digital Camera
\015\012
\015\012This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include “E18 lens error”, or “lens error, restart camera”. Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\015\012The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many Canon's, and NEVER use a case for this very reason.
\015\012A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\015\012Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\015\012The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\015\012Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\015\012Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\015\012Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\015\012Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\015\012Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
\015\012Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\015\012Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\015\012Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Repair Help & Product Troubleshooting for Sony Cyber-shot DSC-W110 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When power is turned on the lens opens and then shuts repeatedly until telling me to turn off the power and start again but doing this just causes it to do the same thing. How can I get it to open an operate properly. The battery is fine as I can view existing photos etc. on the screen.


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Sony Cyber-shot DSC-W110 Digital Camera

Camera shuts down after shutter button is pressed. It shuts down halfway through the shutter operation. Everything else works fine-reviewing pictures, settings in menu, focusing, exposure settings etc. The camera focuses ok when the shutter button is half pressed then when you press the shutter button fully, the mirror goes up, shutter appears to open then the camera shuts down with no power. Only way to get mirror etc back to normal is to remove the battery and refit. When camera is turned b


... Canon EOS 40D Digital Camera

I got this Alba Digital camcorder TDV 521 as a gift from my daughter to india and ever since we brought, we are not able to take any photos or videos. Red light power button will be on soon after we put batteries and press power button. except nothing we could get. we tried to get photos but the camcorder is not opening. can any one suggest me to operate.


... Digital Cameras

Sony DSC-W70 digital camera - Lens attempts to open when pressing the power button but fails with a message to turn off and back on again. Bought a new battery and still does the same thing. Sometimes can get lens to open if tapping it in the palm of your hand while it is attempting to open. Once lens is open camera works normally.


That's a common problem on Cybershot cameras, happened to me twice, the solution is to get it to a camera shop for repair.\012\012The cause could be dirt or a malfunction on the lens extending mechanism. ... Sony Cyber-shot DSC-W70 Digital Camera

When I turn my DSC W230 Sony Camera on the lens opens and closes several times then finally closes and I get a message to turn it off and on again, but it just keeps doing the same thing. I have tired removing the battery for 20 minutes, reinitializing the camera and switching to different batteries that can power up my other camera.


\012Hi, \012\012Error: TURN THE POWER OFF AND ON AGAIN is displayed on the LCD screen when the Lens Mechanism is stuck or when affected by any malfunction. If turning the power on and off again does not resolv ... Sony W230 Digital Camera

Zoom Error Since March 2006 we can not make pictures anymore: Reason is Zoom Error. From one picture to the next this remark shows on the display after we start teh camera. And the lens stays in the camera, the protectionblades does not open, it simply does not do anything anymore and it looks liek the engine does not get power enymore. All other requirements function, like display previous pictures, setting etc. There is also no battery problem, we took them out for 48 hours, but this has no


We have contacted Fujifilm about this problem and they said they'd charge us over $100 US to fix it. There is another thread on this subject \015\012\015\012http://www.fixya.com/support/t143152-fuji_zoom_error_message\015\012\015\012that gives you th ... Fuji FinePix A345 Digital Camera

Yes in my new sx30 IS I opened it new put the battery in it and a chip, and turned it on, powered up ok, then the lense Loudly shakes and after a few seconds the LED readout says lense error, camera will shut down which it does. I restart it again and the same thing happens. Can you help or did I just get a defective camera?


More than likely it sounds like you have a defective camera. ... Canon PowerShot SX30 IS Digital Camera

My camera will not turn on. Just before this happened, I was getting info on the camera that the battery power was low and I had only 10 seconds before it went off. I would put in a new battery and them same thing happened. Finally, the power is off and even when I put in new batteries and check to be sure they are in correctly, I still can't get the power to come on.


Can I have the make and model of the camera? And what type of batteries you are using re-chargable or the regular batteries? ... Digital Cameras

No power I can't get my camera to turn on...yes I've charged, changed, etc. the battery...nothing happens. It's only 9 months old and I had just shot a birthday party the day before. Again I have changed the battery, charged the battery, etc. etc. and when I flip the switch on nothing happens....dead as a door nail!


Both your camera and the battery have a warranty, so I would call Canon and they may replace your battery out of goodwill even though it has been more than 30 days, if you provide your proof of purchase, this is always a possibility...to avoid having ... Canon EOS 400D / Rebel XTi Digital Camera

Began with "low battery". Replaced with new ones. took 3 photos, again message "low battery. Replaced batteries again. Same thing. NOW, , AND BIGGEST PROBLEM CAN'T GET POWER . LENS WON'T RETRACT, POWER BUTTON DOESN'T WORK. I WON'T BE ABLE TO TRANSFER PHOTOS TO COMPUTER. WE'VE TRIED 6 BATTERIES OF THE SAME KIND WE USED BEFORE WHICH. WORKED. It is a Samsung S73. We bought it at Fred Meyer store in Grants Pass, Oregon October 20, 2007 for $129.99. I have successfuly transferred photos to my MACB


Hi there. \015\012You may not like this solution, but it's real anyway. Average low-end digital camera life span is approximately 2 years depending on how much you use it. They vary between manufacturer. Low-end cameras ($100. to $200. range) h ... Digital Cameras

Canon Powershot SD450 E18 problem: The camera lense would not open and reported error code E18 on power-up and then would shut down. I followed a procedure on the web for this issue and got the camera lens to open and it was working (able to take pictures for about a minute). When I powered down, the lense did not completely retract. I tried re-powering on but nothing happened. The camera is not getting any power. I figured the battery died so I re-charged it. I put the fully charged batt


... Canon Digital Cameras

Hi , My Fuji S9600 has just refused to power-up using batteries, although it still powers-up and operates correctly when i attach the mains PSU adapter. I wonder if this is a common occurrence on this model and how easy it is to get sorted. I have used rechargeable batteries since the camera was new (approx 3 yrs) and have tested the batteries as V.good. So i'm assuming that the problem is with the camera somewhere. Do you think if i reset the camera in the menu that would cure the problem , or


A few things here may cause the problem you have First the rechargeable batteries don't hold their charge like alkaline and will drop to zero or near zero voltage in just a few weeks. They may tun on a light but won't have enough power to operate a c ... Fuji Finepix S9600 Digital Camera

I have a SVP T-100 camcorder which all of a sudden stopped working. What is happening is it keeps showing a red light indicating there is no power in the battery and when you connect to the mains it turns green but when you try switching on it goes red again and stays this way!! I have tried a new battery in it and the same thing...the fact that it wont even work from the mains indicates something wrong with the powering getting to the battery or camcorder... Please help. Thanks Maxine xx


... Digital Cameras

Camera was on, working fine. When powering off, telescoping lens did not retract so lens remained extended just a bit with lens cover open. Waited a few minutes, turned it back on and I get the "access" display message then the beeps and (turn power off and back on) message. While off, I have removed the battery, replacing it with a fully charged spare and it still does this. The lens tries to telescope a little bit and retracts a touch, but I can't get the camera out of this mode. Can it be res


Your problem may be due to corrosion on the battery contacts inside the camera\015\012which can prevent the full power of the batteries from flowing into the\015\012camera. Try this free fix before you do anything else: remove the batteries and wip ... Sony Cyber-shot DSC-W55 Digital Camera

The cassette cage holding my tape in my Canon ZR65 camcorder will not release the tape. The door is open and the cage tries to move forward or backward (barely) and then stops---won't open up. I dropped my charger for my battery a few days ago---could the battery not be getting enough power to the camera to release the tape? This has never happened before.


You can test the charger using a multimeter (it has +-0.5 volts from voltage written on charger), or go to a local repair shop and have it tested.A more serious problem is if the tape is stuck inside or the release mechanism is broken. In ... Digital Cameras

My daughter got this cheap Vivitar Vivicam25 digital camera. Problem is it did not come with a disc. I've downloaded 2 drivers and neither one work. I cannot get the pics from the stupid thing onto my computer. I want to get the pics onto the computer. When the batteries die or if you accidently open the battery compartment it erases all the pics. So I need an answer ASAP.


Kindly get it here :\012www.opendrivers.com/.../cameras-and-mp3-player-vivitar-free-driver-download ... Vivitar ViviCam 25 Digital Camera

Canon A400 Hi, I have the above camera (canon power shot A400) and have just solved the E18 error by tapping the plastic A/V out cover - THANK YOU ! However, now, although the camera turns on, lense extends and I get full working order - after a few minutes I get the message 'Change batteriers'. and the camera dies. I have now put in several new batteries (including the little(cr1220) but the same message keeps coming up and the screen and the whole thing dies after a few seconds. Is this a furt


Having using standard LR6 batteries in a Canon before you will only get 3 or 4 pics max before it drains the batteries. You really need high power AA's like 2300mAH+ rechargeables for any good performance or Lithium AA's ... Canon PowerShot A400 Digital Camera

Shutter closed I cannot get the shuttle to open on the camera. It did get drop, but there is nothing that look bad. I have removed battery and recharged it everything powers, but the shutter will not open??


Any small distortion to the case will jam the dust shutter mechanism, as will dislodged dust and dirt. Remove the battery and carefuly remove the case screws. DO NOT LOSE. Lift off the front cover, take care with the top control knob and on/off switc ... Fuji MX-1700 Zoom Digital Camera

I swapped out batteries with the power still on. Now it won't operate properly. The power won't turn off unless I remove the battery and then the lens won't retract. I turn it back on and the lens retracts and then reopens but I can't take pictures.


Hello, You may need to remove battery for 24 hours then reload camera firmware from Kodak website as per user manual directions,the directions are also on the website.Hope this solves your problem,if not,it will be a trip to the repair shop.Regar ... Kodak EasyShare DX6490 Digital Camera

Sony DSC-S600 Sorrry! What happens is this:- Turn camera on,Cybershot screen opens up with musical jingle then it will say "Access" then another screen opens up saying "Turn power off and on again". Sometimes you don't get the "Access" and it will go straight into the "Power off and on again" screen. Tried this - no good. Changed batteries for fully charged brand new 2700mAh NIMH - 1.2V Uniross - still no good ! Any advice would be appreciated. Regards


If you have a memory card in the camera, take it out before turning the camera on ... Sony Cyber-shot DSC-S600 Digital Camera

I have a Toshiba PDR-M700. I cannot get the camera to power on in any mode. Batteries are good and inserted correctly. It was working properly but after turning it off, I couldn't get it to power on again.


... Toshiba PDR-M700 Digital Camera

Code 99 I am able to shoot an image, it is recorded, then I get a code 99. I recycle the power off, I can shoot another single, then I get the code 99 again. Any quick things I might check before I ship it off for repairs? I tried different batteries, checked the voltage on the 3V battery, it's OK, removed & reseated the lens after checking contacts. Thanks


... Canon EOS 40D Digital Camera

Twice recently, I ordered an OEM battery model LI-42B on-line, but both times, after fully charging the battery, the camera does not operate properly with the replacement battery. Once the camera would not turn on, the other time I was able to take only 2 pictures, then the camera would not retract the lens. Have other people had similar problems with OEM batteries? How can I be sure to get a battery that will work with the camera? My camera model is Olympus Stylus 7010 12 megapixel.


This doesn't sound like a battery problem. It sounds like a lens problem. Read this article:\015\012Fixing a Lens Error on a D ... Olympus Stylus 7010 Digital Camera

I have a canon SD1100 I just purchased and after a few minutes the camera will not shut off, the power button won't work and I have to open the battery cover to turn it off. Somehow this completely drains the battery too every time even if it was just charged. Also the camera turns itself on by itself about 10 minutes after you put the battery in it and once again you can't turn it off. I got another battery and the same thing happens. Otherwise it works fine.


If this is a new camera, you should be running back to the store to return it. ... Canon PowerShot SD1100 IS Digital Camera

Panasonic Lumix DMC-Z20 took a knock, now lens gets stuck during power on, grinding noise and lens chugs back and forth for a few seconds. screen displays message "please turn power off and on again". the servo obviously still has power but it seems some part of the mechanism is struggling. any ideas/instructions on how i can crack the thing open without causing irreparable damage? (and should i try...) cheers, Ben. 0405124646 [email protected]


... Digital Cameras
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4513 seconds