Having problems with your Canon Digital Cameras ?
Lens is stuck out and wont go back in. When the camera is turned on message on back screen says "lens error, restart camera"
This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have a canon ixus 900Ti. I turned it on yesterday and the lens came out as normal. when i went to take a pic the camera shut off but the lense never retracted. when i turned the camera back on the splash screen came on, followed by a series of beeps and then and error message saying "lens error, restart camera". restarting has not solved the problem. its like the lens is stuck out. hope you can help Regards Liam
Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Digital Cameras
Lens is stuck out and wont go back in. When the camera is turned on message on back screen says "lens error, restart camera"
Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Canon Digital Cameras
Lens error, restart camera telephoto lens is stuck in zoom position and won't retract, so when i turn on camera, screens says "lens error, restart camera", but it won't restart...just keep coming up with same error message
Hello mnickoliThis is a fairly common error especially with the A560.This either means that something is jamming the lens , or that the\015\012lens sensor is faulty. This is a very , if not the most common problem\015\012with modern digit ... Canon PowerShot A560 Digital Camera
Lens error my canon IXUS 860 IS is having a lens error problem. firstly, the lens cant retract back and when i try to switch it on, the screen will say 'lens error, restart camera' so how do i restart the camera?? i'm currently overseas and although my camera is within warranty, i cant possibly send my camera back to the original country for repair. is there any DIY method?? i'm an amateur at cameras so i do not wish to try any method that may further make the problem worse. thank you for your h
This is probably THE single most common failure among digital cameras. There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... Canon IXUS V2 Digital Camera
The lens on my sd600 won't open when I turn the camera to picture taking position. Screen goes black and message says ''lens error, restart camera''. I have to go back to view mode and then turn camera off and on again in order for partially opened lens to retract fully and close.
Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Canon PowerShot SD600 Digital Camera
I took my camera to the beach, took a picture and put it back in my bag. I then took the camera back out to take another picture the lens extended but then it went back in again it went to go back out but stopped and a loud beeping noise started and a message saying lens error restart camera. I don't know how to restart the camera and if that means turning it of then on it still doesn't work. What can I do now?
If your camera went into "standby" mode, the lens retracted and you may have thought it was off. You put it into the bag and slight pressure on a button reactivated it and the lens tried to come out but may have been prevented by something in the bag ... Canon PowerShot A480 Digital Camera
Lens error My zoom will not work. I can take pictures if I don't zoom, but as soon as I try to zoom in, the screen goes black, the camera beeps a few times and a message that says "lens error, restart camera". However, upon restarting the camera, nothing changes - it still won't zoom!. Also, when turning on the camera, when the lens first comes out...it sounds funny, like it is puttering. Help?
Powershot S3 IS: lens error message, lens juddering on startup but not \015\012coming out. Tried all tricks on internet without success, so decided to \015\012dismantle camera. Localised fault to optical position encoder on first \015\012transfer gea ... Canon PowerShot S3 IS Digital Camera
Lens Error Hi, When I turn on the camera, it says "Lens Error. Restart Camera." When you restart the camera, it gives you the same message. The Canon zoom lens will not go back into the camera. Help!
If you are sure that your battery is fully charged but still does not do any good, then do this little trick:1. Hold the camera on your right hand with the lens facing the ground.2. As you press the power on button, tap or hit ... Canon PowerShot A550 Digital Camera
I have a cannon camera, my boyfriend dropped it with the lens extended and now whenever I try to turn it on I get a message saying that there is a lens error and the camera will shut down. I have tried a couple of answers on this website, but most have to do with a lens that is stuck out, mine will still retract back and forth if you smack it on your hand. My problem is when you power it off and back on the error shows up and the lens will not extend then. Any suggestions are greatly appreciate
... Canon PowerShot SD1300 IS IXUS 105 Digital Camera
My canon IXUS 860 IS is having a lens error problem. firstly, the lens cant retract back and when i try to switch it on, the screen will say 'lens error, restart camera' so how do i restart the camera??
Here are some troubleshooting steps for your lens error problem. And here's a video summary of those steps: ... Canon IXUS 860 IS Digital Camera
My lens is stuck open and all the way out after zooming on a cold evening. The camera turns on, lights up showing G( window and then beeps and goes dark saying 'lens error, restart camera' at
If any amount of moisture has entered the camera this will not be a user fix, it will require service. ... Canon PowerShot G9 Digital Camera
My lens on my Canon IXUS 105 is stuck open and when I push the on/off button I get an error message which says: Lens Error Will shut down automatically Restart camera I can't view pictures, I can't press any of the buttons... I'm not sure where the restart button is. It's a very new camera, I only got it 2 weeks ago. Please help!
Hi,This is a common problem on this set. The lens error is common for cameras with telescoping lenses.\015\012\015\012You can help the motor by connecting the AV cable --- this keeps the LCD off and not d ... Canon PowerShot SD1300 IS IXUS 105 Digital Camera
Lens error When camera is turned on the lens will come out and then right away goes back in-an error message says lens error restart camera
Did you try replacing batteries.will it turn on long enough to restore it?if this is a new camera send it back it could be a software issue or mechanical breakage.Also get a can of air and blow the lens off to ensure no debris is ho ... Canon Powershot SX110 IS Digital Camera 9.0MP
My Canon PowerShot SD850 IS has a lens that is stuck in the extended position. I get a screen that says lens error, restart camera, but when I try to connect to the software, I get a screen on the computer telling me the computer cannot detect the camera. Battery is freshly charged, and I get the little yellow bird picture on the camera when I turn it on. It beeps about 4 times, and then turns off. Is there a safe way to get the lens to retract?
Don't play around with that lens, you can do more damage to the camera and focus with some of the stuff people tell you to try. Your camera just needs to be serviced and you'll be working great again. The shop that specializes in service for the powe ... Canon PowerShot SD850 IS Digital Camera
Hi, i dropped my a560 the other day and the end part of the lens bent a little but i managed to put it back in its original form. however when i press the power button the lenses whirrs and tries to open but goes back in and on the screen it says 'lens error restart camera'. Its my friends camera and i dont want to give it back her in two pieces. please help thank you
Sounds like when you dropped it it damage the gears in the camera that make the lens not work properly , you may want to take it and get it fix by the maker of the camera sorry. ... Canon PowerShot A560 Digital Camera
My daughter was using the camera and she said the lens was stuck in the extended position so she pushed the lens back in ... Now when I try to turn it on an error comes up saying 'lens error restart camera
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is t ... Canon PowerShot SX100 IS Digital Camera
Each attempt I ensue to power on my camera and error displays on the screen saying "Lens error, restart camera". How do I do this for it to be successful? The Lens will not retract and is somehow stuck, what am I doing wrong with the item. It is an A480 Canon camera.
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \015\012probability is that yo ... Canon PowerShot A480 Digital Camera
When I turn on the camera, it says "lens error, please restart". The lens doesn't open when you turn on the camera- it is like it is stuck shut. you can manually force it open, but it won't go automatically, and so it keeps on giving the error messages.
HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that you wi ... Canon PowerShot SD600 Digital Camera
I PoweShot SD1300 Is that is less than a year old. The lense is stuck open and I get an error message saying Lens Error Will Shut Down Automatically - Restart Camera. I've tried to restart and even removed the battery but the lense remains stuck. Please advise. Thank you - Paul Murakami
HelloThank you for using FIXYA!!!This\012 is a suggestion. If you do not feel comfortable trying it, ... Canon PowerShot SD1300 IS IXUS 105 Digital Camera
Lens problem The lens on my cannon powershot A1000 will not open. When I try to turn on the camera it makes a buzzing sound like it's trying to open and then a message comes on the screen saying lens error restart camera. This camera is pretty new so I'm not sure why the sudden problem.
You should have dropped your cam down to the floor or you should have forcibly tried to put your lens inside when the servomotor lens tried to bring the lens out..take your camera to the nearest service centre..you should not try to open the cam sinc ... Canon Powershot A1000IS 10MP Digital Camera with 4x Optical Image Stabilized Zoom
My canon powershot a590 camera lens is stuck. When I attempt to start my camera I get a message saying Lens Error Restart Camera then the camera immediately powers off.
Lens errors are fairly common. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or ... Canon PowerShot S2 IS Digital Camera
When I turn on my camera (Canon power shot SD600) it won't come on... I get a series of three beeps then a message on the screen that says "lens error, restart camera." The problem is, I don't know how to restart my camera.
Take it to a proffesional... ull need a new lens and more likely a whole new camera but dont start buying until u ask someone that know ALOT about cameras anyway id have to see it up close to know wat excatly is worng. !!!! try cleaning ur lens !!!! ... Digital Cameras
I dropped my camera today, and since then, I can't power down correctly. The lens will not go back in, and I can't use the camera at all, not even to view pictures already taken. I get a message that says lens error, restart camera. Can you help?
Try wriggling the lens LIGHTLY as you power off and see if you can get it to go in.\015\012If that doesn't work, I hope you have insurance, as it will need to go in for repair.\015\012It is damaged. Sorry for the bad news. ... Canon PowerShot SD600 Digital Camera
Hi! Im Michelle from Dubai UAE, i bought my canon elph series camera last july 09 only and just yesterday after turning on the device the lens was stock up and not turning to its place anymore,.i tried to turn it off and on again but the camera is only blinking and there's a message on the screen says "Lens error, restart camera" ...I would realy appreciate any positive feedback,..Thank you very much for your kind attention Sincerely, Michelle Email:[email protected]
Hello.....\015\012sir it might be a lense problem i guess............the spring with which lense moves may be not proper............. slidin of lense is not aceessble by ur cam...........so better if show it to ur provider.......they replace it ... Canon Elph Jr. APS Point and Shoot Camera
My lens on my camera seems to be stuck. I have a Power Shot SD790 IS. Every time i try to turn my camera on it starts to beep and a message says that there is a lens error, restart the camera. How do i fix this?
Unfortunately, many cameras that fall prey to lens error problems can only be corrected by professional repair. But if the camera is out of warranty or the cost estimate for professional repair approaches the value of the camera, ... Digital Cameras