Having problems with your Panasonic Lumix DMC-FS3 Digital Camera ?

When I turn on my Lumix DMC-FS3 Camera the lens tries to go out but it does it half way, then it goes in and the action is repeated about three times. Then there is a message on the display that says "Please turn off your camera and then turn it on again". I do that and the process repeats. Thank you.


Answers :

Fixing a Lens Error on a Digital Camera
\012


\012

This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.
\012

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous intreriors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.
\012

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.
\012

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
\012

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:
\012

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.
\012

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.
\012

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particals that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.
\012

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.
\012

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).
\012

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.
\012

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.
\012

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Repair Help & Product Troubleshooting for Panasonic Lumix DMC-FS3 Digital Camera

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I turn on my Lumix DMC-FS3 Camera the lens tries to go out but it does it half way, then it goes in and the action is repeated about three times. Then there is a message on the display that says "Please turn off your camera and then turn it on again". I do that and the process repeats. Thank you.


Fixing a Lens Error on a Digital Camera\012\012This has to be THE most common failure mode for a digi ... Panasonic Lumix DMC-FS3 Digital Camera

Malfunction Hi there,i do have this message displayed when i turn the camera on.It says please turn camera off and then on again.i have tried several times,even removing the battery and memory card for a while.im puzzled and dont know what to do.please help


You guys all have lens faults which can not repaired without any experience on repairs. camera should be sent into a panasonic repair centre. ... Panasonic Lumix DMC-FX3 Digital Camera

My sony cyber-shot dsc-w55 7.2 mega pixel camera turn on but the lens goes in and out many times and i get the word access on the screen then i get a message says turn the power off and on again, I did that many times , but it did not work, and I can't get the menu button to work or display any thing, so I am wondering what is the problem and how to fix it?


... Kodak EasyShare CX6200 Digital Camera

There are several problems with my camera one of them is the fact in that Every time i turn on my Lumix 10x mega pixel camera the lens won't focus it also won't let me take any pictures. When i turn the camera off the lens won't go back into the camera but when i turn it back on the lens gos in and then out again. There is one more problem whenever i go to look at the pictures on play i can look through a few before its says "please turn camera off then on a again" it also says the same message


OK, if there is sand in the camera, the gears will bind or stop causing the error that you described. I think it needs to be taken apart and cleaned by a service center before using again. Or you could buy a spare caemera to use on your family holida ... Digital Cameras

My camera was dropped accidentally while capturing a image. After that i switched off and when I switched on for next snap, display shows access and after few seconds a message appears saying" Turn the power off and on again" I did this several times but no effect and even i removed the battery and inserted back still no use. Please help.


I am a technician who repair any electronic devices, i repair digi cam a few hours ago, foreign object or dust is not the cause of that error, digi cam has 3 lenses, 1 is outside lens, 2 is is the swinging lens and 3 is the retractable lens,... do no ... Sony Cyber-shot DSC-W55 Digital Camera

Optio E10 When I turn my camera on I get an error message that says "memory card error", I purchased a new memory card but still get the same error message...any suggestions? I have the exact same problem with my Pentax Optio S7. I turn on the camera and it displays the message Memory Card Error. I have tried several new cards and get the same message. There is an option on the menu to format a card, but you can't access the menu if you have the card installed. It takes great pictures without t


HelloOK, if the memory card itself is locked, you might \012sometimes get this error code. All you need to do is to take out the \012memory card and switch the lever on the left side to the unlock. ... Pentax Optio S7 Digital Camera

The camera says please turn camera off and then on again every time i turn it on I dropped my camera and now when I turn it on the lens goes back and forth and the display reads "Please turn camera off and then on again"


Hi,\015\012I too have the sam problem but was able to solve it. I called the 1-800-number and was told that this is a very common issue or this camera. They told me to tap the lens when it was extended on a cloth or ... Panasonic Lumix DMC-TZ3 Digital Camera

Hi, I own a Sony Cybershot camera, and it has been giving a few problems as of this week. The lens keep re-adjusting in and out when I turn the camera on to take pictures. It however responds just fine when in picture-view mode. There is a screen prompt that says 'Access' when the camera is turned on, as well as the message 'turn off camera and start again'. I do not think that the camera had fallen at any time, and it is just under a year old. Thanks a lot for your response, Sarah.


... Digital Cameras

The entire zoom lens will not come out when I turn the camera on. It moves a little, makes a sound, and then my camera says turn off camera off and back on. I tried that several times and it is still not working. The battery is charged. I did go to the beach and wondering if sand got into the camera. I also cannot review my pictures as the message comes up about turning it off. What is the best solution?


HelloThe problem is that the lens has become stuck in the barrel\012 after dropping it. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional.Use\012\012\01 ... Panasonic Lumix DMC-TZ3 Digital Camera

When I turn my camera on it says "Access" then a message comes up that tells me to "turn the camera off and then on" I have tried this many times and all the camera does is continue to push the lens in and out and then tells me to "turn camera off then on" Problem will not go away. Fully charged battery, took battery and memory card out for a while and re-inserted both and have same problem. [DSC-W55


This is a firmware problem that is common with many many digital cameras. It will have to be upgraded. The company will do this for $50Otherwise you may be able to find a kit online and do it which would be hard to located ... Sony Cyber-shot DSC-W55 Digital Camera

My cannon rebel will not take picture or go to the menu the only thing it will do is turn on. And when i turn it on a message pops up that says "shooting is not possible. Turn the power switch to off and on again or re-install the battery." I have tried turning the camera on and off and reinstalling the battery multiple times but nothing works. Do i have to take my camera to a camera shop to get fixed or could i do something at home to fix it??


I think either shutter unit or cmos unit faulty. you cant fix at home you have take to canon repaired centre ... Canon EOS Rebel XSi Digital Camera

Access Message Whenever I turn the DSC-W70 on it displays a black screen and the word "Access." At the same time the lens extends and retracts, however unlike some of the other problems people are having, the lens is not getting stuck. Also I also notice a faint clicking/buzzing sound from within the camera when the lens is still and not retracting/extending. After about 10 seconds it begins to beep and displays the message "Turn the power off and on again." I am able to view previously taken ph


Could not believe it but it worked for me as well. First time I see that a good smack makes it work ... Sony Cyber-shot DSC-W70 Digital Camera

Every time i turn the camera on it beeps like 5 times and it says to turn the camera off and on and i do but it is the same message over and over.Thanks


Your camera has a lens error, this\015\012 is such a common fault that I hope you don't mind me pasting my stock \015\012generic a ... Sony Cyber-shot DSC-W55 Digital Camera

Faulty d40x hi i bought a d40x off ebay the other day and couldnt wait to start snapping.... problems: - The error message "initialization error. Turn camera on and off again" appears. Upon turning the camera off and on again, the same message appears. After several times trying it still does not work. Also, the menu screen appears, and just keeps flicking from menu to menu constantly. As well as this, on the playback mode, the picture of the image displayed keeps zooming in as far as


I would start by looking at all of the push buttons on the camera. One may be stuck down. ... Nikon D40x Digital Camera

Hello there, i have had my tz15 for 18 months and have never had a problem it until now. I taking video at the time and then I went to zoom in and the lens started to do so maybe 1x, hesitated then retracted back into the camera as if it had been turned off and a message displayed on the white screen "Please turn camera of then on again". This doesn't work, i can still take photos but when i try to zoom the same thing happens every time. I was taking some shots and video of some electric arc we


I had the same problem. Tried on and off and press every button and it still tells me to "Please turn camera of then on again". I took my SD card out, turn it on in display mode, select menu, go to internal memory, erase all files in the intern ... Panasonic Lumix DMC-TZ15 Digital Camera

Access Message Whenever I turn the DSC-W70 on it displays a black screen and the word "Access." At the same time the lens extends and retracts, however unlike some of the other problems people are having, the lens is not getting stuck. Also I also notice a faint clicking/buzzing sound from within the camera when the lens is still and not retracting/extending. After about 10 seconds it begins to beep and displays the message "Turn the power off and on again." I am able to view previously taken ph


This is a hardware problem. Your simptons is tipical of a lens position sensor being faulty.\015\012\015\012There is however nothing you can do yourself. Contact your nearest Sony dealer and take the camera to a Sony service centre. ... Sony Cyber-shot DSC-W50 Digital Camera

When I turn on the camera (Lumix DMC-FX35) the lens goes in and out a few times and then displays a message telling me to Please turn camera off and then on again I have done this several times and the lens problems persists What should I do?


... Panasonic Lumix DMC-FX35S Digital Camera

When i turn on my camera it zooms in and out over and over never focusing and then displays the message ''PLEASE TURN CAMERA OFF AND THEN ON AGAIN''. When i do this it repeats the smae thing evey time i turn the camera on. AND IT HAS THE ERRORS SYSTEM ERROR FOCUS


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic Lumix DMC-FX7 Digital Camera

WHEN I TURN ON MY COOL PIX S51 A LENS ERROR MESSAGE COMES ON THE SCREEN AND DOESNT ALLOW AN OTHER FUNCTION WITH THE CAMERA. THE LENS COVER IS STUCK OPEN WHEN THE MASSAGE IS DISPLAYED. IF I TURN THE CAMERA ON AND OFF A FEW TIMES THE COVER WILL CLOSE BUT THE ERROR MASSAGE REMAINS. IM NOT SURE WHY THIS HAPPENS AND IVE NEVER DROPPED MY CAMERA AND ITS ALWAYS STORED IN A FOAM CASE. I CANT AFFORD ANOTHER CAMERA RIGHT NOW, IS THERE ANY SOLUTION TO MY PROBLEM?


HelloThe problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the \012probability is that ... Nikon COOLPIX S51 Digital Camera

I have a panasonic lumix DMC-TZ3 camera and it's not working. When I turn it on, the lenses comes out/goes in like 3 times but it won't focus and stay open. I can't take a picture. A message says to turn it off and turn it back on again, but it doesn't work. I can view my album in the the camera....please help!


Fixing a Lens Error on a Digital Camera\015\012\015\012This has to be THE most common failure mode for a digit ... Panasonic Lumix DMC-TZ3 Digital Camera

When I turn on my panasonic digital camera DMC-LZ7 (with fresh batteries) it attempts to focus but cant then displays a message saying "turn off camera and turn back on again". If i do this, the same problem appears


Looks like a problem with the CCD sensor. Try removing batteries, and SD card for 5 minutes. Replace new batteries and try again.If issue persists, you will have to get the piece serviced. ... Panasonic Digital Cameras

I need some help to repair my Sony Cybershot DSC W50 camera. When you turn the camera on, it displays 'Access' for about 30 seconds, during which time the lens zooms in and out. Then it says 'Turn the power off and on again'. Nothing has happened to the camera - it has not been dropped and this fault just suddenly started. What can I do about this? I have had it just over a year. I’d be really grateful for any support! Thank you! Clare


When the camera is switched on it turns the lense out to a certain position and locks , but if due to any reason if the lense does not reaches to its proper position it retracts back and tries again 2 or 3 times, and then the movement haults and pr ... Digital Cameras

My camera says 'Connecting to PC' all the time when I turn it on even if it is not connected to PC. I think it has got confused as the last time I used the camera was to take photos off it and it may have run out of charge while connected to the PC. I cannot use the camera as it always has this 'Connecting to PC' message on it.


Connect the camera to your PC. Turn it on. Wait till the PC 'acknowledges' the camera. Then disconnect it via 'remove USB-device safely'-function.If this doesn't work. try resetting the camera with the reset button you'll find under the c ... Nikon D40x Digital Camera

My Canon Powershot A560 memory card is locked and it is the camera doing it not the memory stick.And there is nothing in the manual about how to fix it. When I turn on my camera I get an error message"memory card error" then when i press to view pictures it says the memory card is locked and turns itself off. I have had this camera for some time and have never had issues uploading pictures onto my computer or with the memory card.I really would rather not lose the pictures that are on the camer


Remove the memory card from the camera. Note that there is a small slide switch on one of the long edges of the card. Slide the switch to unlock or lock the card. ... Canon PowerShot SD750 / IXUS 75 Digital Camera

I turn on my Panasonic DMC-FX8 camera and it softley buzzes and clicks. Then I get a message on the display saying to turn the camera off then turn it on again. The battery is recharged. Any ideas?


The lens stuck, you need send it for repair. It’ll be a lot of money for replacing the lens. Is it still under warranty? ... Panasonic Lumix DMC-FX8 Digital Camera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.lionebra.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3785 seconds